StyleWell HDFP48-54E Plainfield 48 Inch Freestanding Electric Fireplace TV Stand Instruction Manual

Model # HDFP48-54E
# HDFP48-54AE
OMSID # 320084812
# 320084652
ASSEMBLY INSTRUCTIONS
Plainfield 48in Coil Media Electric Fireplace

THANK YOU
We appreciate the trust and confidence you have placed in Stilwell through the purchase of this electric fireplace/heater. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs.
Thank you for choosing Stilwell!

Safety Information

Please read and understand these instructions before assembling and using this console. Save these instructions for future reference.
MAXIMUM RECOMMENDED WEIGHT LOADS
WARNING: This unities not intended for use with CRT TVs. Use only with flat panel TVs and audio/video equipment meeting recommended size and weight limits. Never use with larger/heavier than recommended fiat panel TVs or equipment. To avoid instability, place fiat panel TV in the centre of the unit; the base of the television must be able to rest on the supporting surface of the unit without over-hanging the edges.
Improperly positioned flat panel TVs, or flat panel TVs or other equipment that exceed recommended size and weight limits could fall off or break the unit, causing possible serious injury.

Warranty

We are confident that you will be delighted with this purchase. Should this product be defective in workmanship or materials, or fail under normal use, we will repair or replace it for a period of up to one (1) year from date of purchase.
This warranty gives you specific rights and you may also have other rights which vary from state to state.
Contact the Customer Service Team at 1-877-527-0313 or visit www.HomeDepot.com.

Pre-Assembly

PLANNING ASSEMBLY
Compare all parts with the Hardware Included and Package Contents list. If any part appears missing or damaged, do not assemble this product and contact the Customer Service Team at 1-877-527-0313.
TOOLS REQUIRED
Phillips screwdriver (not provided)
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.

PACKAGE CONTENTS

Assembly

1. Preparing base assembly
   NOTE: Do not fully tighten all bolts until you finish assembling all parts. Once assembled, go back and fully tighten all bolts. This will mak the assembly easier.

2. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a carpeted floor or the empty carton to avoid any scratches.

3. Securely screw the cam bolts (EE) into the designated small holes on the bottom panel (M) and skirtings (N, P and Q) using a Phillips screwdriver.

4. Gluing wood dowels
   NOTE: Refer to the dowel guide drawings in this step for further clarification on how to properly glue in the wooden dowels. Apply this method whenever instructed to install wood dowels.

5. Glue the wood dowels (CC) into the designated holes of the skirtings (N, O, P and Q). It is very important to use a small amount of glue on both ends of dowels and wipe away the excess glue immediately.
   

6. Attaching rear skirting
   NOTE: Refer to the cam lock assembling guide drawings in this step for further clarification on how to properly install cam locks. Apply this method whenever instructed to install cam locks.

7. 1. Attach the rear skirting (0) between the side skirtings (P and Q) by engaging two cam locks (DD).

8. Attaching front skirting

   • Align and attach the front skirting (N) to the side skirtings (P and Q) using two cam locks (DD).

9. Assembling base

10. Using the wood dowels (CC) as a guide, align and attach the previous assembly to the bottom panel (M) by engaging eleven cam locks (DD).

11. Preparing bottom panel, partitions and media shelf assembly

12. Securely screw the cam bolts (EE) into the designated small holes on the top surface of bottom panel (M), media shelf (L) and both partition panels (S and T) using a Phillips screwdriver.

13. Gluing wood dowels

14. Glue the wood dowels (CC) into the inner holes on the side panels (R), partition panels (S and T), middle top crossbar (B1) and middietrims (C1) as shown.

15. Attaching middle trims

16. Attach the middle trims (C1) to the partition panels (S and T) respectively by engaging two cam locks (DD) per stile.

17. Attaching middle crossbar

18. Attach the middle crossbar (B1) to the media shelf (L) by engaging three cam locks (DD).

19. Attaching partition panels

20. Using the wood dowels as a guide, firmly press the assembled partition panels (S and T) to the bottom panel (M) and fasten them in place with four long flat head screws (GG).

21. Attaching side panels

22. Align and attach the side panels (R) to the bottom panel (M) by engaging four cam locks (DD) as shown.

23. Attaching media she

24. Position the media shelf (L) onto the vertical panels properly and fasten it in place by engaging eight cam locks (DD).

25. Preparing top section assembly

26. Ask for assistance to lift the assembly unit upright.

27. Securely screw the cam bolts (EE) into the designated small holes on the top panel (K), media shelf (L) and upper moldings (X, Y and 2) using a Phillips screwdriver.

28. Gluing wood dowels

29. Glue the wood dowels (CC) into the designated holes on the panels (V and W) and moldings (A1, X and Y) as shown.

30. Attaching upper side front moldings

31. Orient and attach the upper left front molding (X) to one upper side panel (V) with two cam locks (DD) as shown.

32. Repeat the same process to combine the upper right front molding (Y) and the other upper side panel (V) together.

33. Attaching upper partition molding

34. Attach the upper partition molding (Z) to the upper partition panel (W) by engaging two cam locks (DD).

35. Attaching top front stretcher

36. Attach the top front stretcher (A1) to the top panel (K) by engaging three cam locks (DD).

37. Attaching side panel and partition panel assembly

38. Align and attach both assembled side panels (V) and partition panel (W) to the top panel (K) by engaging six cam locks (DD).

39. Fasten top front stretcher

40. Insert four medium flat head screws (RR) through the countersunk holes on the top front stretcher (A1) and securely screw into the upper front moldings (X and Y) using a Phillips screwdriver.

41. Attaching top assembly

42. Using the wood dowels as a guide, place the assembled top onto the media shelf (L) properly and fasten it in place by engaging six cam locks (DD).

43. Installing back panels

44. Now, go back and securely tighten all the cam locks and screws. Make sure all the parts are tight and there are no gaps between the parts. This will help keep the unit square.

45. Ask for assistance to flip around the previous assembly at its front edges. Pick up the upper back panel (F1) and align the pre-drilled holes against the upper long edge with the pilot holes on the back of top panel (K). Fasten it in place with the provided washer head screw (HH).

46. Using the pilot holes as a guide, align and attach the side back panels (E1) to the mantel frame with the washer head screws (HH).
    NOTE: We recommend attaching back panel with the screws at the corners first.

47. Attaching mending plate

48. With the pilot holes as a guide, fasten the middle crossbar (B1) to both middle trims (C1) by attaching two mending plates (JJ) at the joints, using two short flat head screws (FF) per plate.

49. Installing door hinges and handles

50. Extend two door hinges (PP) and rest the hinge cups onto the cutouts of each door (U). Secure the door hinges (PP) in place by using two nickel screws (QQ) in each.

51. Attach one handle (MM) to the front side of each door (U) with two handle bolts (NN).

52. Attaching door panels

53. Ask for assistance to lift the assembly unit upright and position it near the final location.

54. Pick up the one door (U) and fasten the hinge bases onto the left side panel (R) with four nickel screws (QQ) in each, using the pilot holes as a guide.

55. Repeat the same process to attach the other door (U) to the right side panel (R).

56. Open and close the doors to make sure they are aligned and shut correctly. If necessary, adjust the screws for a good fit. Refer to the hinge sticker on door for adjustment.

57. Attaching adjustable shelves

58. Open the doors and insert four shelf supports (KK) in the holes at the desired height inside each side compartment. Make sure you place the four shelf supports at the same level to make the shelf level. Tilt and rest the adjustable shelves (G1) onto the  shelf supports.

59. Putting cam covers and bumpers

60. Plug the cam lock covers (00) onto the visible cam locks to conceal the cams.

61. Stick the rubber bumpers (1l) on the outer corners of doors where the partition panels (S and T) are in contact with.

62. Attaching upright arms
    IMPORTANT NOTE: Use hand screwdriver, not power driver to assemble fireplace insert. See BILT for video instructions.

63. See figure A: Fasten upper 2 screws (AA) through the upright arm (C) into the heater (A) until tight.

64. See figure B: Fasten lower 2 screws (AA) into the upright arm (C) until tight.

65. Fully tighten all 4 screws (AA) one final time.

66. Repeat the same process with upright arm (B).
    WARNING: Do not it or ranspor the heater by using the upright arms.

67. Attaching logs to ember bed
    IMPORTANT: Carefully follow the 2 steps below for inserting each log.

68. Install left log (F) into left hole of ember bed (E) by inserting front edge of base of the log into front notches of ember bed hole.

69. Then tilt the log back to insert the rear edge of the log base into rear notches of ember bed hole (press down log firmly to lock into position).

70.  Repeat the above process for the right log (G).

71. Positioning ember bed

72. Seethe ember bed (E) onto the heater (A) as shown.

73. Push ember bed forward against the front flange of heater.

74. Position the USB cable as shown below.

75. Attaching wall panel

76. Fold the wall panel (H) as shown. Then position yourself at back side of heater (A).

77. Hold wall panel (H) at the angle shown below and insert lower back edge into metal slots on back of heater (A).

78. Tilt wall panel (H) forward until bottom corner inserts into lower U-channels on both upright arms (B and C).

79. Continue to tilt wall panel (H) forward until the top corner inserts into upper U-channels on both upright arms (B and C).

80. Connecting ember bed cable to heater

81. Fully plug the USB connector of the ember bed (E) into the back port of heater (A).

82. Inserting the glass

83. Slide the glass (1) into the inner U-channels on both upright arms (B and C) until the glass sits onto the heater (A). If needed, push top of upright arms in or out to accommodate glass. Make sure the top of the glass (1) is flush with the top of both upright arms (B and C).

84. Positioning connector strap

85. Position top connector strap (D) over the glass (1) and upright arms (B and C). Follow orientation shown below.

86. Attaching connector strap

87. Fasten connector strap (D) to both upright arms (B and C) using two screws (AA) as show below. Holes must be in line for screw to pass through.

88. Finishing fireplace insert assembly

89. The firebox is now ready for the next assemble step.

90. Installing fireplace insert

91. Lift the fireplace insert carefully into the back of the assembled mantel and center it on the bottom panel (M) in the opening.

92. Using the pilot holes as a guide, fasten two L-shaped brackets (LL) onto the firebox holder (D1) with four pan head screws (BB), Make sure that the right-angle side is flush with the short edge of firebox holder (D1).

93. Using the pilot holes as a guide, fasten the firebox holder (D1) between the partition panels (S and T) with four pan head screws (BB).

94. Installing acrylic stopper

95. Remove the paper backing of acrylic stopper (SS), then properly align the acrylic stopper into the cutout on the acrylic stopper template on the front of the top panel (K). Press down on the acrylic stopper to help adhesion.
    NOTE: To prevent your TV from tipping, you must install the acrylic TV stopper if you place a flat panel television on the top panel. Otherwise, skip to next step.

96. At the back of top panel (K), grip the heads of plastic tacks with pliers, with twisting motion pull tacks loose to remove the acrylic stopper template.

97. Installing tipping restraint hardware
    WARNING: Young children can be seriously injured by tipping furniture. You must install the tipping restraint hardware with the unit to prevent the unit from tipping, causing any accidents or damage. The tipping restraints are intended only as a deterrent, they are not a substitute for proper adult supervision. The tipping restraints are not earthquake restraints. If you wish to add the extra security of earthquake restraints, they must be purchased and installed separately.

98. With assistance, position the assembled fireplace at the desired location against a wall. If necessary, adjust the pre-attached floor levelers by hand to correct tilting and level the doors, until the unit is level.

99. Follow the instructions printed on the plastic bag containing the tipping restraint hardware to attach the tip-over restraints to the unit and the wall.

100. Connect the fireplace to the power transformer. Follow the operating manual for the electric fireplace insert to control your fireplace.

WARNING

• Unit must be placed on a level surface or leveled with included hardware (when applicable).
• Do not sit or stand on or allow children to climb, sit or stand on the assembled product.
• For safety reasons, it is imperative that this unit be mounted to the wall or floor.
• Unit can tip over causing severe injury or death.
• Never open more than one drawer at a time.
• Do not exceed the recommended weight limits.
• Before cutting, drilling or hammering into any wall or floor surface, verify the location of electrical, plumbing and gas lines. Cutting may cause serious injury.

Care and Maintenance

A touch-up pen has been provided to minimize the small nicks or scratches that may occur during assembly or shipping.
To clean and care for your furniture:

• Use a soft, clean cloth that will not scratch the surface when dusting.
• Use of furniture polishes is not necessary. Should you choose to use polishes, test first in an inconspicuous area.
• Using solvents of any kind on your furniture may damage the finish.
• Never use water to clean your furniture as it may cause damage to the finish.
• Always use coasters under beverage glasses and flowerpots.
• Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing.
• Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create spotting within the furniture finish.
• In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a professional to repair your furniture.
• Check bolts/screws periodically and tighten them if necessary.

CARING FOR WOOD FURNITURE

It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful tips will enhance your furniture as it ages.

CLEANING THE FIREPLACE TRIM

Clean the metal trim using a soft cloth, slightly dampened with citrus oil based product and buff with a clean soft cloth. DO NOT use brass polish or household cleaners as these products will damage the metal trim. Citrus oil based products can be obtained at supermarkets or hardware stores.

Questions, problems, missing parts? Before returning to the store,
call Style Well Customer Service
8 a.m. – 7 p.m., EST, Monday-Friday, 9 a.m. – 6 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM
Retain this manual for future use.

Documents / Resources

| StyleWell HDFP48-54E Plainfield 48 Inch Freestanding Electric Fireplace TV Stand [pdf] Instruction Manual
HDFP48-54E, HDFP48-54AE, HDFP48-54E Plainfield 48 Inch Freestanding Electric Fireplace TV Stand, Plainfield 48 Inch Freestanding Electric Fireplace TV Stand, 48 Inch Freestanding Electric Fireplace TV Stand, Freestanding Electric Fireplace TV Stand, Electric Fireplace TV Stand, Fireplace TV Stand, TV Stand, Stand
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>