AiDot M2 Pro 2K Indoor Security Camera User Guide
- June 12, 2024
- AIDOT
Table of Contents
AiDot M2 Pro 2K Indoor Security Camera
IN THE BOX
PRODUCT OVERVIEW
- Magnetic Mount
- Magnet Contact
- Micro SD card slot
- Reset Button
- Light Sensor
- Indicator light
- Lens
- Table Stand
- Wall Mount
- Speaker
- Micro USB Port
- Mic
APP SETUP
- Download the AiDot APP and sign in or create an account.
- Connect the camera to a power outlet and waiting for the green flashing light with ‘Waiting for Wi-Fi configuration· audio.
- lntheAiDot app, press·+·, select M2, and follow the instructions on App.
- Place the camera in the area where you plan to install to test the video quality, ensure that the camera can work normally after the final installation.
INSTALLATION
WALL INSTALLATION
Drill a hole with a 11/64 inch (4.36mm) drill bit, then insert the anchor
into the hole. The anchor is necessary for walls that are made by hard
materials such as concrete, brick or stucco. (3M tape can be used to fix the
position before screw driven in).
LIGHT INDICATIONS
CAUTIONS
To avoid personal injury and/or possible product damage, the following cautions must be followed:
- Please use sorely the provided adapter instead of others in case of any damage to the product.
- Keep out of reach of children. This product contains small magnets and other small parts, which can cause choking or injury if ingested.
- To prevent early failure, the camera should only be installed in operating environments ranging between 0°C ~ 40°C (32°F ~ 104°F).
- Do not install
- in wet locations
- outside the premises (outdoors)
- close to heat source
- near the metal objects and mirrors that cause radio signal attenuation or shading.
- Do not disassemble or reinstall the camera, otherwise it may cause security risks0.
- Unplug the power cord before cleaning. Do not clean it with any liquids, spray cleaner or wet cloth.
- The slot and opening are used for ventilation, not allowed to be blocked or covered
FCC
Note: The grantee is not responsible for any changes or modifications not
expressly approved by the party responsible for compliance. Such modifications
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this f equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance of 20 cm between the radiator and vour bod.
RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance of 20 cm between the radiator and your body.
ISED Statement
This device contains license-exempt transmitter (s) /receiver (s) that comply
with Innovation, Science and Economic Development Canada’s license-exempt RSS
(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. Pour see conformer aux exigences de conformité CNR 102 RF exposition, une distance de séparation d’au moins 20 cm doit être maintenue entre l’antenne de cet appareil ettoutes les personnes.
NEED HELP?
Contact our support team: support@iwinees.com
Linkzone Technology Co., Limited ROOM 20 5/F WAYSON COMMERCIAL BLDG28
CONNAUGHT ROAD WEST SHEUNG WAN, Hong Kong, China.
Phone: 1-855-334-9800
Website: www.iwinees.com
Email: support@iwinees.com
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>