Tymor 33-D5030BL Centinel 3 Bluetooth Digital Deadbolt Instruction Manual
- June 12, 2024
- Tymor
Table of Contents
Tymor 33-D5030BL Centinel 3 Bluetooth Digital Deadbolt
Safety Information
Read the precautions and instructions in this manual before installing and using this lock. Save this manual for future reference. Lisez les consignes et instructions contenues dans le présent manuel avant d’installer et d’utiliser cette serrure. Conservez le présent manuel pour consultation ultérieure.
A. Do not attempt to disassemble any internal components of the lockset. Doing
so will void the limited warranty.
B. Do not drop or hit the lockset. Too much shock may result in permanent
damage.
C. Do not use pins or sharp objects to press the keypad.
D. Always create a backup of information you want to keep (such as the admin
code and entry codes). Please use the last page of this booklet as your
reference.
E. The lockset comes WITHOUT the default Admin Code. Please follow the
instructions to set up the Admin Code.
CARE AND MAINTENANCE
The following instructions should be followed to properly protect and maintain your lockset: Les instructions d’entretien suivantes doivent être respectées afin de garantir un fini durable:
A. Remove locks, or do not install locks, prior to painting your door.
B. Periodically clean with mild soap and a soft cloth only.
C. Do not use any abrasives or chemical products containing alcohol, benzene,
acids, and avoid using sharp or abrasive objects to clean this lockset.
D. Do not allow any water or liquids into the lockset during installation.
Pre-installation – Tools Required
WARNING
If the door needs to be drilled, be familiar with how to use your drill
safely, and understand all the door preparation steps before proceeding.
| Part | Description | Quantity |
|---|---|---|
| AA | 2-1/16″ (52 mm) Mounting Bolt | 2 |
| BB | 1-1/4″ (31.7 mm) Screw ［The correct hole sizes. Ø 2-1/8″ (54 mm) ］ | 1 |
| CC | 3/4″ (19 mm) Screw | 2 |
| DD | 3/4″ (19 mm) Wood Screw | 4 |
| DD-1 | 1-1/4″ (31.7 mm) Wood Screw | 2 |
| EE | 3″ (76 mm) Wood Screw | 2 |
| Part | Description | Quantity |
|---|---|---|
| A | Key | 2 |
| B | Exterior Assembly | 1 |
| C | Cylinder | 1 |
| D | Torque Blade | 1 |
| E | Power Cable | 1 |
| F | Mounting Plate | 1 |
| G | Interior Assembly | 1 |
| H | Battery Cover | 1 |
| I | Latch | 1 |
| J | Bottom Plate (Optional) | 1 |
| K | Square or Radius Faceplate (Optional) | 1 |
| L | Drive-in Collar (Optional) | 1 |
| M | Drive-in Collar (Optional) | 1 |
| N | Strike Plate | 1 |
Door Preparation
NOTE: If your door is pre-drilled, check the hole sizes to make sure they are the proper size. If they are the proper size, skip to the INSTALLATION section.
Using the template, mark the door and drill the holes, and chisel out a
mortise.
NOTE: Drill from both sides of the door to prevent wood splitting.
Prepare the door jamb – use the strike plate as a template to drill the latch and screw holes and chisel out the mortise. The strike plate must fit flush with the surface of the door jamb.
Door jamb hole dimension
a. 1-1/8″ (28 mm)
b. 1″ (25 mm)
c. 1″ (25 mm)
Strike dimentions
d. 3/32″ (2.5 mm)
e. 2-3/4″ (70 mm)
f. 1-1/8″ (28 mm)
TEMPLATE
NOTE: Double check your product for the correct hole sizes.
Installation
INSTALLING THE LOCK ASSEMBLIES
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>