MIYOTA FS10 Chronograph 3 Eyes Quartz Watch Instruction Manual
- June 12, 2024
- MIYOTA
Table of Contents
MIYOTA FS10 Chronograph 3 Eyes Quartz Watch
Product Information
The product is a watch with chronograph functionality. It has three different models: Cal. FS10, Cal. FS11, and Cal. FS13. The watch can measure time up to 59 minutes and 59 seconds with a timing accuracy of 1/1 second. It has multiple displays and buttons, including hour hand, minute hand, second hand, chronograph minute hand, chronograph second hand, button A, button B, and a crown. The watch also has a date display.
Product Usage Instructions
Displays and Buttons
The watch has the following displays and buttons: – Hour hand – Chronograph minute hand – Second hand – Chronograph second hand – Button A – 24-hour hand – Minute hand – Crown – Button B – Date
Setting the Time
If the crown is of the screw-lock type, follow these steps: 1. Loosen the screw by turning the crown to the left before operating it. 2. After performing the desired operation, return the crown to its normal position. 3. While pushing in the crown, turn it to the right to securely retighten the screw.
Setting the Date
To set the date, follow these steps: 1. Pull the crown out tothe time correction position when the second hand is at the 0 seconds position. 2. Turn the crown to set the time. The 24-hour hand moves along with the hour hand, so pay attention to AM and PM. 3. Securely return the crown to its normal position in synchronization with a telephone or other time service.
Using the Chronograph
The chronograph function of the watch can measure and display elapsed time up to 59 minutes and 59 seconds with a timing accuracy of 1 second. After reaching 59 minutes and 59 seconds, it resumes timing from 0 seconds. The chronograph minute hand continues tomove even after 55 minutes and 59 seconds have elapsed. To use the chronograph, follow these steps: 1. Start timing by pressing button A. 2. Press button A to stop the chronograph. 3. To reset the chronograph to 0 seconds, press button B.
Chronograph Reset (including after replacing the battery)
If the chronograph second-hand does not return to the 0 seconds position or has shifted out of position due to a strong impact o after replacing the battery, perform the zero positioning of the chronograph hands according to the following procedure: 1. Starttiming by pressing the button A. 2. Press button B to reset the chronograph to 0 seconds.
CHRONOGRAPH FUNCTION
CENTER SECOND HAND CHRONOGRAPH 1/1 sec.
Timing up to 59 minutes 59 seconds
- A) DISPLAYS AND BUTTONS
- B) SETTING THE TIME
- C) SETTING THE DATE
- D) USING THE CHRONOGRAPH
- E) CHRONOGRAPH RESET (INCL. AFTER REPLACING BATTERY)
DISPLAYS AND BUTTONS
SETTING THE TIME
In the case the crown is of the screw-lock type.loosen the screw by turning the crown to the left before operating crown,and after having returned the crown to the normal positionfollowing operation,turn the crown to the right while push-ing it in to securely retighten it.
SETTING THE DATE
-
Pull the Crown out to the time correction position when the second hand has reached the O seconds position.
-
Turn the crown to set the time.
The 24-hour hand moves in conjunction with the hour hand. pay attention to AM and PM when setting the time. -
Securely return the crown to the normal position in synchronization with a telephone or other time service.
Hint for Accurately Setting the Time
After stopping the second hand at the O seconds position. turn the minute hand 4-5 minutes past the conect time and then turn it back to the correct time. The time on the watch can then be set to the correct time by pushing in the crown insynchromzation with a time service tone.
USING THE CHRONOGRAPH
- The chronograph function of this watch is able to measure and display elapsed time up to 59 minutes 59 seconds in I second units. After the chronograph dis plays elapsed time for 59minutes 59 seconds. It resumes timing from 0 seconds.
- The chronograph minute hand continucs to move until the chronograph is stopped by pressing button(A)even after 55 minutes 59 seconds have elapsed.
-
pull the crown out to the date correction position.
-
Turn the crown to the right to set the date.
The crown turns freely and the date does not change if the crown is turned to The left.
If the date is set while the time on the watch is between the hours of about 9:00PM and 1:00AM, the date may not change on the followind day/
If this happens,set the date after temporarily moving the hands to a time other than between the above times.
The date is based on a 31 -day Calendar.
The date must be changed from the last day Of the month to the first day of the following month for those months not having 31 days (months having 30 days and February). -
Once the date has finished being set, return the Crown to the normal position.
CHRONOGRAPH RESET (INCL. AFTER REPLACING BATTERY)
When resetting the chronograph after replacing the battery, if the chronographsecond hand does not return to the 0 seconds position or if the chronograph second hans has shifted Out of position due to a strong impact,perfornl zero positioning of the chronograph hands according to the procedure described below.
Chronograph Timing
-
Start timing by pressing button (A).
The chronograph is repeatedly stalled and Stopped by pressing button (A). -
Pressing button (B) resets the chronograph to O seconds
Chronograph Hand Zero Positioning]
- pull the crown out to the time correction position.
- press button (A) to position the chronograph second at the 0 position. The chronograph second hand can be advanced rapidly by depressing button (A) continuously.
- Once the chronograph second hand has been positioned at the O position, reset the time and return the crown to the normal position.
- press button (B) to check that each of the chronograph hands has been reset to the O position.
These specifications might be changed without prior notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>