AUX 63993221 Split Air Conditioner Instruction Manual
- June 12, 2024
- AUX
Table of Contents
63993221 Split Air Conditioner
Product Information
The product is an air conditioning system consisting of indoor
and outdoor units. It requires proper installation and connection
before operation. The user manual provides detailed instructions on
the steps to be followed for successful installation and checks to
ensure safe and efficient operation.
Product Usage Instructions
Step 1: Air Evacuation (Page 6.1)
-
Ensure that the indoor and outdoor units are securely
installed. -
Check for any fall, vibration, or noise issues.
-
Verify that there are no refrigerant gas leaks.
-
Ensure proper thermal insulation of the refrigerant gas and
liquid pipes, as well as the indoor drain hose extension. -
Check for any water leakage and ensure that the draining line
is properly installed. -
Ensure that the system is properly grounded to prevent
electrical leakage.
Step 2: Electrical and Gas Leak Checks (Page 6.2)
-
Use only specified wires for all wiring and ensure correct
connection of all wires. -
Check for any operation or burn damage.
-
Ensure that the air inlet and outlet of both the indoor and
outdoor units are unobstructed. -
Verify that the stop valves are opened.
-
Check if the indoor unit properly receives remote controller
commands. -
Measure the voltage between L and N (115V) or between L1 and L2
(220V). -
Ensure that the pipes and wires are connected to the
corresponding terminal blocks/connection ports for the connected
unit.
Step 3: Test Run (Page 6.3)
Perform the following checks to ensure proper cooling/heating
function:
-
Verify that both the indoor and outdoor units are installed
securely. -
Check for any refrigerant gas leaks.
-
Ensure that the refrigerant gas and liquid pipes, as well as
the indoor drain hose extension, are thermally insulated. -
Inspect for any water leakage and ensure the proper
installation of the draining line. -
Check if the system is properly grounded.
-
Confirm that only specified wires are used for all wiring and
are connected correctly. -
Ensure that there is no operation or burn damage.
-
Verify that the air inlet and outlet of both the indoor and
outdoor units are unobstructed. -
Check if the stop valves are opened.
-
Ensure that the indoor unit properly receives remote controller
commands. -
Measure the voltage between L and N (115V) or between L1 and L2
(220V). -
Make sure that the pipes and wires are connected to the
corresponding terminal blocks/connection ports for the connected
unit.
Note: It is important to follow all the steps and checks
mentioned in the user manual for safe and efficient operation of
the air conditioning system.
1.6
AFTER CONNECTION, BEFORE OPERATION…………………………6 Step 1: Air
Evacuation…………………………………………………….6.1 Step 2: Electrical and Gas Leak
Checks………………………………6.2 Step 3: Test Run……………………………………………………………6.3
Step 2:Install drain joint
Step 3:Anchor Outdoor Unit
6 After Connection, before operation
Step 1: Air Evacuation
Page 6.1
6 After Connection, before operation
Step 2: Electrical and Gas Leak Checks
Page 6.2
6 After Connection, before operation
Step 3: Test Run
Test Items
Indoor and Outdoor units are isntalled securely
Symptom
Check
Fall, Vibration, Noise
No refrigerant gas leaks
Incomplete cooling/ heating function
Refrigent gas and liquid pipes and indoor drain hose extension are thermally insulated
Water leakage
Draining line is properly installed
Water leakage
System is properly grounded
Electrical leakage
Only specified wires are used for all wiring, and all wires are connected correctly.
No operation or burn damage
Indoor or outdoor unit’s air inlet or air outlet are unobstructed.
Incomplete cooling/ heating function
Stop valves are opened.
Incomplete cooling/ heating function
Indoor unit properly receives remote controller commands
No operation
Voltage between L and N is 115v; or between L1 and L2 is 220V
Pipes and wires are connected to the corresponding terminal bloks/connection
ports for the connected unit.
No operation No cooling / heating
Page 6.3