HAT Design Works Innovative One Touch Freestand Instruction Manual
- June 12, 2024
- HAT Design Works
Table of Contents
HAT Innovative One Touch Freestand
Product Information
The One Touch Freestand is a standing desk unit designed for use with monitors. It features a sturdy base unit with adjustable legs,an upper and lower worksurface, a power box with cord, and optional monitor arms. The unit is equipped with Human Active Technology for easy adjustment and ergonomic positioning.
Included Parts
- A: 4, 5, 6mm Allen Keys
- B: Lower Worksurface Screws
- C: Power Box w/Cord
- D: Legs
- E: Base Unit/Lift Assembly
- F: Upper Worksurface
- G: Switch
- H: Switch Screws
- I: L Brackets
- J: Monitor Arms (included with Dual Bundle only)
- K: Pivots (included with Dual Bundle only)
- L: Upper Worksurface (included with Dual Bundle only)
- M: Right & Left Monitor Arms (included with Dual Bundle only)
Additional Parts Included with Dual Bundle ONLY:
Product Usage Instructions
-
Step 1: Lay unit down face up on a solid, sturdy hard surface. Use provided allen key (A) to loosen the four 6mm allen screws that come pre-assembled on the underside of the lift assembly.
-
Step 2: Slide the legs (E) on the lift assembly (D), making sure rubber pads are on the underside of the legs and the base of the lift assembly, where they will be touching the desk in the upright position.Use the provided Allen key (A) to loosen the four 6mm fallen screws on the underside of the lift assembly (D).
-
Step 3: Re-tighten the screws at the base of the unit to secure the legs to the base.Slide the legs (E) onto the lift assembly (D), ensuring that the rubber pads are on the underside of the legs and the base of the lift assembly.
-
Step 4: Loosen the screws in the middle of the worksurface support brackets as shown here. These screws may be loosened with the included #5 allen key or by hand based on preference.Tighten the screws at the base of the unit to secure the legs to the base.
-
Step 5: Slide the upper worksurface (F) into the support brackets as shown:Loosen the screws in the middle of the worksurface support brackets.
PLEASE NOTE:
Make sure to fully insert into brackets into the slots as far as they can go. There are small screw stops in place that will stop the worksurface once it has reached its correct position.
-
Hand tighten the thumb screws to secure the worksurface into place.
-
Step 7: Turn unit upright to standing position on desk or hard surface for the remaining installation steps.
-
Step 8: Align t-nuts to parallel on L bracket (J) parallel to each other.
-
Step 9: Slide L bracket onto base unit, allow L brackets to drop down to worksurface.
-
Step 10: Tighten bolts with 5mm hex key.
-
Step 11: Route the cables from the switch (G) through the opening in the upper worksurface.
-
Step 12: Attach the switch to the upper worksurface with the two Phillips head screws (H).
-
Step 13: Plug the connector from the switch located on the top worksurface to the port on the left side of the actuator motor as shown below.
-
Step 14: Route the power cable (C) coming from the actuator motor out the back of the unit through the notch in the back cover and attach the power cord extension.
-
Step 15: With the unit placed securely on the desk, lower work surface (I) over brackets.
-
Step 16: Screw the lower worksurface on to the right angle brackets with the flat head screws (B) and the supplied 4mm allen key.
This concludes installation instructions for the One Touch Freestand unit! Enjoy!
If you have purchased a Freestand Bundle, please continue to follow the remaining installation steps: -
Step 17: Slide the monitor arms (K) into the vertical post from the top and use the plastic knobs to secure in place. Leave them flush with the top of the post for a neutral monitor position. Note that these are adjustable to allow a larger range of monitor positions.
-
Step 18: Attach monitor to pivot (L) using provided Phillips head screws (M).
-
Step 19: One attached, slide monitor pivot into the pivot pocket located on each arm.
-
Step 20: Enjoy your new One Touch Freestand Bundle!
If you have purchased a Freestand Bundle, please follow the additional installation steps:
- Slide the monitor arms (K) into the vertical post from the top and use the plastic knobs to secure them in place.
- Leave the monitor arms flush with the top of the post for a neutral monitor position.
- Note that the monitor arms are adjustable to allow for a larger range of monitor positions.
These are the complete installation instructions for the One Touch Freestand unit. Enjoy using your standing desk!
WARNING : Never operate unit with more than two monitors without securing the unit to the desk. The unit could possibly tip over causing bodily injury or product damage.
Slatwall units (model numbers containing -S and -SFCG) must be installed on a slatwall or in front of a wall/panel, not on an open desk.
Human Active Technology
- 800 524 2744
- customerservice@team-hat.com
- team-hat.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>