BERNINI FOUNTAINS 001354 Marcelli Fountain Instruction Manual
- June 12, 2024
- BERNINI FOUNTAINS
Table of Contents
BERNINI FOUNTAINS 001354 Marcelli Fountain
Assembly Instructions
WARNING
Read instructions carefully and DO NOT plug in the fountain until assembly is
complete.
Notes:
- Choose an appropriate location for the fountain.
- Excessive weight or pressure on any of the fountain sections may cause it to fall. Keep pets, children, or anyone from sitting, leaning, or climbing on any of the fountain components.
- While the fountain is designed to operate as splash-free as possible, some water splashing out of the fountain is inevitable. Place the fountain in a location where any splashing will not cause damage.
- The National Electric Code requires that a ground fault circuit interrupter (GFCI) be used in the branch circuit supplying the fountain pump and other pond equipment. Seek your electrical supplies dealer for this device.
- Keep the fountain always working with sufficient water and clean of debris and dirt to ensure the proper functioning of the pump.
- Clean your fountain with a soft cloth and change the water when necessary. Due to water evaporation, you may see a buildup of white residue on the fountain surface from the mineral content in the water supply. To prevent such buildup, clean your fountain with damp cloth. Do not use any abrasive or chemicals to clean as they may ruin the finish.
- See the pump instructions for pump safety, maintenance, and warranty information.
- Keep this manual for future reference.
Installation & Assembly
- Place the fountain on a level surface, away from areas where it is likely to get clogged with leaves, and make sure that the cable will reach the socket.
- Follow the steps to assemble as below illustration marks.
Figure’1-5’
Step (1) Connect the big plate and pedestal tightly as the arrowheads
indicate.
Figure’2-5’
Step (2) Get the wire of the pump through a plastic pipe of big plate center.
Make sure the wire is put into the pedestal’s cavity. Step (3) Connect the
pillar and big plate tightly as the arrowheads indicate.
Figure’3-5’
Step (4) Connect the medium plate and pillar tightly as the arrowheads
indicate.
Figure’4-5’
Step (5) Put a plastic hose into the plastic pipe of the medium plate center
then connect the top part and medium plate tightly as arrowheads indicate.
Figure’5-5’
- Step (6) Connect the plastic hose to the pump outlet.
- Step (7) Please close the small door to the pillar of big plate center.
- Steps (8) and (9) Fill the big plate with enough clean water to assure the pump works properly. Plug the pump, water will start to flow in a few minutes.
- Adjust the pump flow rate to achieve the desired effect and minimize any splashing. Splashing can occur if the flow rate is too high or the reservoir is too full. The flow rate can be increased or decreased by moving the flow rate control slider on the pump body. Moving the switch towards ‘+/ Max.’ will increase the flow rate and moving it towards ‘-/Min’ will decrease it. On some type of pumps, the flow regulator may be turned clockwise or anticlockwise to adjust.
Troubleshooting
UNPLUG FROM POWER SOURCE BEFORE YOU CHECK THE FOLLOWING ** If pump does not run:
- Check the circuit breaker, try another outlet.
- Check the water level in the fountain. Running the pump without sufficient water can damage the pump.
- Check the setting of the flow control on the pump and adjust the flow.
- Check the pump discharge and intake for dirt and debris.
- Check the fountain feature tubing for kinks and obstructions.
- The pump might be “air locked”. Plug and unplug the pump several times to release the air inside the pump.
- Check and reconnect all the cords and try again.
LIMITED ONE-YEAR WARRANTY
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. This product has a one-year limited warranty on all materials and workmanship. Bernini® warrants the original purchaser of this product that the product will be free from manufacturing defects in workmanship and material for a period of one (1) year from the date of the original purchase. If within one (1) year this product fails due to defect in material or workmanship, Bernini® will repair, replace or supply any defective part at their discretion. The purchaser must contact Bernini® and provide a description of the defective part, including digital pictures if requested, with this original purchase documentation as validation of warranty coverage. This warranty does not cover or apply to: (a) damage to the product due to misuse, mishandling, and abuse, (b) products not used in accordance with instructions, (c) product not assembled or installed according to instructions, and (d) normal wear and tear. Call us for assistance at +1 619-449-2392 or you can email or mail us at: 9545 Pathway Street, Santee, CA 92071, [email protected], Our Customer Care Department is available: Monday – Friday 8:30 am to 4:00 pm PST / 11:30am – 7:00pm EST
Please read first before returning:
Please call us for assistance at
1-619-449-2392 or email us at
[email protected]. Our Customer Care Department is available:
Monday – Friday 8:30 am to 4:00pm PST, and 11:30am to 7:00 pm EST. If you have
any questions regarding assembly, parts, or operation, please visit our
website at www.berninifountains.com. You will find instructional videos on how
to assemble and operate your fountain and keeps you up to date on our newest
products. You can also email us with any questions you have. This product
comes with a one-year limited warranty against materials and workmanship.
- January 2023 © Yeiser Research & Development LLC and Bernini Fountains® Trade names, product names, and logos used in this document are the trademarks or registered trademarks of Yeiser Research & Development LLC, Santee, CA 92071
Santee, California 92071 | World Wide Patents Pending | Email: [email protected] | On the web: www.berninifountains.com Facebook & Pinterest: Bernini Fountain Company | Instagram: @berninifountains Twitter: @yrdllc © Yeiser Research & Development, LLC; 2023. All rights reserved.
Scan this QR code for the latest version of these instructions