HEXAERO HX406253 Cube ID-CAN Remote Controller Instruction Manual
- June 12, 2024
- HEXAERO
Table of Contents
HEXAERO HX406253 Cube ID-CAN Remote Controller
Overview
Cube ID_CAN is small size (25mm 13.75mm 3.5mm ) Remote ID which broadcasting information about UAVs in flight through a Bluetooth 5.2 dual- mode unit, supports both CAN and serial protocols. Users can write different codes with one Cube ID only, to adapt to multiple UAVs based on their needs.
Hardware Specification
Operation instruction
- Connect the Cube ID_CAN to the CAN1 Connector of flight control, and view the transmission data in the mobile phone software Drones.
Installation
Connect the CAN or Serial port on module and flight controller with the
suitable cable(we provide 4 Pin CAN cable,6 Pin and 8 pin Serial cable) .
Stick the module to UAV with a regular sticker or soft sticker (with slight
vibration isolation).
Keep the antenna away from the propeller.
Settings
Remark: Cube ID has not been ready on standard APM firmware. Must create
OpenDroneID firmware. Please check the following web to build the firmware :
https://ardupilot.org/dev/docs/opendroneid.html#opendroneid
https://www.youtube.com/watch?v=Az8v4Kx4hS0
-
Connect the flight controller to computer via a USB cable. Open Mission Planner （latest version）. Install the OpenDroneID firmware by “Load custom firmware”.
-
Go to “Full Parameter List” and find “DID_ENABLE”. Change it to “1” to enable ODID.
-
Go to “Full Parameter List” and find “CAN_P1_DRIVER”. Change it to “1” to enable CAN.
（or if you use serial port ,find Serialx_PROTOCAL and change it to mavlink ）
-
Go to MissionPlanner homepage select Drone ID to set (1)UAS ID* (2)UAD ID Type and (3)UA Type
to set (1)UAS ID (2)UAD ID Type and (3)UA Type
Go to Operation to set (1)Operator ID , (2)Oper ID Type , (3)Self ID DESC and (4)Self ID Type
Testing
Download DroneScanner for IOS，OpenDroneID or DroneScanner for Android to
detect and monitor nearby UAVs.
Warning
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Second label must be place on the outside of the final device that contains the following text: “Contains FCC ID: 2A7W3-HX406253” The FCC ID can be used only when all FCC compliance requirements are met.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>