Jane Wooddy Evolutionary Highchair Instruction Manual

Jane Wooddy Evolutionary Highchair

Safety Instructions

IMPORTANT! READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
WARNING

• Never leave the child unattended.
• Always use the restraint system.
• Always position the 5 safety harnesses over your child, checking that they are fastened correctly in the central clasp.
• Ensure that they are correctly fastened and adjusted to the size of your child.
• Falling hazard: Prevent your child from climbing on the product.
• Do not use the product unless all components are correctly fitted and adjusted.
• Be aware of the risk of open fire and other sources of strong heat in the vicinity of the product.
• Be aware of the risk of tilting when your child can push its feet against a table or any other structure.
• Keep children away when unfolding and folding the product to avoid injury.
• The Baby high chair is not suitable for children that cannot sit unaided.
• Do not use the high chair if any of the parts are broken or missing.
• DO NOT place this product near a window where cords from blinds or curtains could strangle a child.

ASSEMBLING THE BASE OF THE HIGH CHAIR (STOOL)

• Fit the 2 front legs (A and B)
  Place the seat upside down on a clean, flat surface.
  Insert each leg into the front supports of the seat, press the unlocking button and press the legs inside until the button slots into place (you will hear the safety click when it is in place)
  Fit each of the 2 end covers on the end of each leg, press the unlocking button and press them on as far as they will go (they will click into place).

• Fit the 2 rear legs (C and D)
  Insert each leg into the rear supports of the seat, press the unlocking button and press the legs inside until the button slots into place (you will hear the safety click when it is in place).
  Fit the 2 end covers with the metal bar on the end of each leg, press the unlocking button and press them on as far as they will go (they will click into place).

• Fit the side supports
  Position each plastic side support with the smooth part facing outwards, fit and tighten the 2 screws with the Allen key supplied, regularly check that the screws remain tightly fastened.

• Fit the footrest
  Position the footrest between the 2 front legs and on each side slot the 2 lateral guides of the plastic support into the inner wooden runners on the leg.
  Underneath the footrest on each side fit and tighten the plastic side screws A and B.
  Set the other 2 screws that support the footrest underneath to position 1.

• FIT THE SEAT
  Fit the 4 plastic supports underneath the seat into the 4 large holes in the stool.
  Once the 4 supports have been slotted into place, hold the seat with bo push it firmly backwards until it clicks into place.
  Check that the locking button is activated.

  • Check that the pin is visible and activated and the seat is firmly locked in place
  • Fit and make sure the safety lock is ALWAYS tightly fastened, check this regularly.

• FIT THE TRAY
  Open the 2 catches found on the bottom of the tray and insert it into the 2 side supports of the seat, release the catches in the required position (2 positions).

• FIT THE SAFETY HARNESS

  • First insert the plastic anchor of the shoulder strap into the side clasp of the harness, then insert these 2 parts together into the central clasp until you hear it click into place.
  • Always position the 5 safety harnesses over your child, checking that they are fastened correctly in the central clasp.
  • To fit the harness to the baby slide the strap through the rectangular clasps.
  • Ensure that they are correctly fastened and adjusted to the size of your child.
  • Temporarily remove the belt, harness, crotch strap and the tray and then fit them again at the end of this stage.
  • Fit the footrest in the lowest position.

• REMOVE THE SEAT:
  Un screw the safety screw found underneath the seat.
  Keep the seat unlocking button pressed down and simultaneously push the seat forwards to fully release it. Put the stool cushion on by fitting the 2 Velcro straps through the 2 slots and fasten them under the seat.

MAINTAINING

Cleaning Clean the plastic and wooden parts with a damp cloth with soap and water.
Washing the cover Remove the cover, wash it by hand and leave it to dry at room temperature. To install the cover again, do the same as before, but in reverse order.

GUARANTEE INFORMATION

• This item is guaranteed against manufacturing defects as stipulated in the legal Directives and/or regulations in force on guarantees for consumer goods applicable to the European Union and those of the country in which it is marketed.
• It is essential to present the purchase invoice or receipt in order to process the guarantee through the seller of the Item (I, failing that through the manufacturer.
• The guarantee excludes anomalies or faults caused by misuse, non-compliance with the safety regulations and instructions for use and maintenance provided, or due to wear and tear caused by normal use and regular handling of the item.
• The label containing the serial number of your model must not be torn off under any circumstances as It contains infonmation relevant to the guarantee.

JANE, S.A.
Pol. Industrial Riera de Ca Ides
C/. Mercaders, 34
08184 Palau Solita i Plegamans -BARCELONA
Tel. +34 93 703 18 00
Fax. +34 93 703 18 04
(www.janeworld.com)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>