COSTCO 5125179 Animated Witch with Lights and Sound User Manual
- June 12, 2024
- Costco
Table of Contents
COSTCO 5125179 Animated Witch with Lights and Sound
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
CARE AND STORAGE INSTRUCTIONS
When not in use, store this product in its original packing. Keep away from
heat and moisture.
Please read all instructions carefully before assembling. Save this
instruction sheet for future reference.
For decorative indoor and outdoor use.
WARNING
This item is not a toy and should be used for decoration only. This item contains small parts that can be a choking hazard. Keep all plastic and wire parts away from children.
- Please use the adapter supplied by manufacturer.
- Please assemble item according to instructions. Connect all wires according to matching color.
- Children should be supervised by adults. Item should not be grabbed, as it becomes a tipping hazard.
- Keep all flammable objects away from the adapter, as it heats up during operation.
PARTS LIST
- A. Base Front x 1
- B. Base Back x 1
- C. Lower Poles x 2
- D. Upper Poles x 2
- E. Support Struts x 2
- F. Lower Body Frame x 1
- G. Costume x 1
- H. Hip Hoop x 1
- I. Upper Body Frame x 1
- J. Left Arm x 1
- K. Left Hand x 1
- L. Sleeve Cuffs x 2
- M. Right Arm x 1
- N. Right Hand x 1
- O. Head x 1
- P. Hat x 1
- Q. Stakes x 4
- R. Adapter x 2
PLEASE REMOVE AND LAY OUT ALL PARTS FROM THE BOX PRIOR TO ASSEMBLY. IF PARTS ARE MISSING, DO NOT ATTEMPT TO ASSEMBLE THE PRODUCT AND CONTACT CUSTOMER SERVICE (SEE LAST PAGE FOR CUSTOMER SERVICE CONTACT INFORMATION).
ASSEMBLY INSTRUCTIONS
STEP 1
Attach the Base Front (A) to the Base Back (B) by using the available quick connect push buttons and pre-drilled holes as shown in Figure 1.1. Attach the Lower Poles (C) to the Base Back (B) using the available quick connect push buttons and pre-drilled holes as shown in Figure 1.2. Attach the Upper Poles (D) to the Lower Poles (C) using the available quick connect push buttons and pre-drilled holes as shown in Figure 1.3. Slide the Struts (E) into the housings available on the Base Front (A) and in the housings available on the Upper Poles (D) as shown in Figure 1.4.
STEP 2
Attach the Lower Body Frame (F) to the Upper Poles (D) using the available quick connect push buttons and pre-drilled holes as shown in Figure 2.
STEP 3
Slide the Costume (G) over the assembly so that the opening of the Costume (G) is aimed towards the back as shown in Figure 3.1. Slide the prongs of the Hip Hoop (H) into the housings available on the Lower Body Frame (F) as shown in Figure 3.2.
STEP 4
Attach the Upper Body Frame (I) to the Lower Body Frame (F) using the available quick connect push buttons and pre-drilled holes as shown in Figure 4.1. Bring the Costume (G) up over the shoulder area of the Upper Body Frame (I) as shown in Figure 4.2.
STEP 5
Slide the Left Arm (J) up the left sleeve of the Costume (G) as shown in Figure 5.1. Remove the cotter pin from the forked hook of the Left Arm (J) and then set. Set the forked hook of the Left Arm (J) into the housing available on the left side of the Upper Body Frame (I) and then slide the available cotter pin into the hole at the bottom of the forked hook on the Left Arm (J) as shown in Figure 5.2.
STEP 6
Slide one of the Sleeve Cuffs (L) over the end of the Left Arm (J) as shown in Figure 6.1. Remove the cotter pin from the forked hook of the Left Hand (K) and then slide the forked hook of the (K) Left Hand into the housing available at the end of the Left Arm (J). Then put the cotter pin back into the hole available on the forked hook of the Left Hand (K) as shown in Figure 6.2. Then fit the elastic of the Sleeve Cuff (L) over the wrist of the Left Hand (K) as shown in Figure 6.3. Attach the sleeve of the Costume (G) to the Left Hand (K) by using the available hook & loop closure as shown in Figure 6.4.
STEP 7
Slide the Right Arm (M) into the right sleeve of the Costume (G) as shown in Figure 7.1. Remove the cotter pin from the Right Arm (M) and then set the forked hook of the Right Arm (M) into the housing available on the right side of Upper Body Frame (I). Then slide the cotter pin into the hole available at the bottom of the forked hook on the Right Arm (M) as shown in Figure 7.2.
STEP 8
Slide the remaining Sleeve Cuff (L) onto the end of the Right Arm (M) as shown in Figure 8.1. Remove the cotter pin from the forked hook of the Right Hand (N) and then slide the forked hook of the Right Hand (N) into the housing available at the end of the Right Arm (M). Then slide the cotter pin into the hole available at the bottom of the forked hook on the Right Arm (M) as shown in Figure 8.2. Connect the cable available from the Right Arm (M) to the corresponding cable available from the (M) Right Arm. Then fit the elastic of the Sleeve Cuff (L) onto the wrist of the Right Hand (N) as shown in Figure 8.3. Attach the sleeve of the Costume (G) to the Right Hand (N) by using the available hook & loop closure as shown in Figure 8.4.
STEP 9
Note: If the Hat (P) elastic is not adjusted properly, it may impact the witch’s mouth movement. Place the Hat (P) onto the Head (0) onto the (0) Head so that the hair of the Hat (P) is not covering the face. Bring the elastic of the Hat (P) far under the chin of the Head (0) as shown in Figure 9.1. Further attach the Hat (P) to the Head (0) by using the available hook & loop closures available at the front and back of the Head (0) as shown in Figures 9.2 and 9.3.
STEP 10
Flip the witch so that the back of the assembly is aimed upwards as shown in Figure 10.1. Remove the cotter pin from the forked hook of the Head (0). Slide the forked hook of the Head (0) into the housing available at the top of the Upper Body Frame (I) then slide the cotter pin into the hole available at the bottom of the forked hook of the Head (0) as shown in Figure 10.2.
STEP 11
Connect all cables from the Function Control Box available on the Lower Body Frame (F) to their corresponding cables by shape and color as shown in Figure 11.1. Attach the Sensor to the inner front surface of the Costume (G) using the available hook & loop closure as shown in Figure 11.2.
STEP 12
Close the back of the Costume (G) by using the available hook & loop closures as shown in Figure 12.1. Flip the witch so that the front is aimed upwards and then lift the witch up so that it stands on the Base (A, B). At least 2 people are needed for this step, one person holds the Base (A, B) firmly in place and the other lifts as shown in Figure 12.2.
STEP 13
If the witch is being displayed outdoors, plunge the Stakes (Q) through the holes on the Base (A, B) and into the ground as shown in Figure 13.
Your 10 FT Animated Witch is now fully assembled. Plug in and turn on to let the fun begin!
OPERATION INSTRUCTIONS
- Plug the Adapter into a standard power outlet and adjust the settings on the Function Control Box, located on Lower Body Frame (F), as desired.
- Settings:
Timer: This setting activates the sound, light, and animation each time the Infra-red (IR) sensor is triggered within a 6 hour period. The item will then deactivate for 18 hours and then reactivate for 6 in a continuous cycle. 6H ON/18H OFF. The Infra-red (IR) sensor has a range of up to 2 m I 6.5 ft I 6.5 pi.
Sensor: This switch mode will only activate lights, sound, and animation when the Infra-red (IR) sensor is triggered. The item will operate tor 1 audio-cycle with each sensor activation. The Infra-red (IR) sensor will activate when someone comes within an 80-degree angle from left-to-right, as well as from above and below. The Infra-red (IR) sensor has a range of up to 2 m / 6.5 ft/ 6.5 pi.
OFF/Try me : This switch mode will turn the lights, sounds, and animation off. If item is used with a Try Me accessory (not included), this setting will only activate lights, sound, and animation for one audio-cycle when the Try Me accessory (not included) is activated. To use a Try Me accessory (not included}, remove the rubber cap from the Try Me jack receiver and insert the Try Me jack. When not using a Try Me accessory (not included), firmly plug the Try Me receiver with the rubber cap.
| ON: This setting continually operates the lights and the LCD screens without animation or sound.
Multi-lingual Sounds: This is a 4-toggle switch mode with the following adjustable sound settings.
EN – English vocals with background sounds
ES – Spanish vocals with background sounds
FR – French vocals with background sounds
Non-Linguistic Vocals, background sounds only
Raise or lower the volume using the volume control turn dial, turn all the way down to turn the volume off.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate
the receiving antenna, Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. Consult the dealer or experienced
radio/TV technician for help.
CAN ICES-003(8) / NMB-003(8)
CUSTOMER SUPPORT
Distributed by:
Costco Wholesale Corporation
P.O. Box 34535
Seattle, WA 98124-1535
USA
1-800-774-2678
www.costco.com
MADE IN CHINA
FOR CUSTOMER SERVICE ASSISTANCE, CALL:
US toll-free 855-428-3921, English
Only. (Calls from outside the US incur fees at the normal rates by country),
9:00 am to 5:00 pm, Monday – Friday, Pacific Time, North America.
Seasonal Visions International Inc.
Berkeley, CA 94710 USA
customerservice@svius.com
Please use the adapter supplied by manufacturer.
Manufacturer: YINGJIAO ELECTRICAL CO.,LTD.
Commercial registration number: 9133O22671335284XG
Address: Cuijia, Xidian Town, Ningbo, China 315613
Model: YSC2O-O593OOO
Input: 1OO-24OVAC, 5O/6OHz
Output Voltage: 5.9V
Output Current: 3.OA
Maximum output power: 17.?W
Average active efficiency (%): 82.39%
Efficiency at low load (1O%): 85.56%
No-load power consumption: O.O82W
CAUTION
Do not connect the chain to the supply while in packaging. For decoration
purposes only. The light source is not intended for use in other applications.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>