sistemamt SMARTB12IP 20w Battery Powered Ellipsodial Led User Manual

SMARTB12IP
20W BATTERY POWERED ELLIPSODIAL LED

USER MANUAL

PRODUCT S PECIFICATIONS

TECHNICAL SPECIFICATIONS
LEDMODULE

1.2 SIZE CHART

1.3 SAFETY WARNING
IMPORTANT
[ALWAYS READ THE USER MANUAL BEFORE OPERATION. ] [PLEASE CONFIRM THAT THE POWER SUPPLY STATED ON THE PRODUCT IS THE SAME AS THE MAINS POWER SUPPLY IN YOUR AREA.]

• This product must be installed by a qualified professional.
• Always operate the equipment as described in the user manual.
• A minimum distance of 0.5m must be maintained between the equipment and combustible surface.
• The product must always be placed in a well ventilated area.
•  Always make sure that the equipment s installed securely.
• DO NOT stand close to the equipment and stare directly into the LED light source
• Always disconnect the power supply before attempting maintenance.
• Always make sure that the supporting structure is solid and can support the combined weight of the products.
• The earth wire must always be connected to the ground.
• Do not touch the power cables if your hands are wet.

ATTENTION

• Do not operate in a sealed enclosure with insufficient air flow
• Do not operate in an environment with temperatures in excess of 45deg. C
• Do not operate store in close proximity to source of fire.
• Always charge with supplied charger
•  Do not charge for more than 24 hours
• Always turn off battery storage switch when storing for longer than 7 days
• Always store with full load
• Always charge with flightcase open
• Always carry out one full discharge and charge cycle every 3 months
• Always store in a dry environment away from direct sunlight

GETTING STARTED

2.1 OPERATING POSITION

2.2 GENERAL OPERATION

1.  When charging, power light is red, when finish charging, power light s green
2.  When turn on fixture, it” s static mode, red light is off.
3.  If no DMX signal when turn on fixture, green light is flickering
4.   If there is DMX signal when turn on fixture, green light is always on
5.  Whenit’ sunder infrared mode and there is infrared signal, red light is flickering

DISPLAY PANEL OPERATION

3.1 DISPLAY OPERATION
◆MENU: BACK;
◆ENTER: ENTER OR SAVE;
◆ DOWN: DOWN;
◆Up: Up 3.2 MENU MAP

3.3 EDITSTATIC COLOUR

• Combine [RED], [GREEN], [BLUE], [WHITE], [AMBER] , [CYAN] and [UV] to create an infinite range of colors (0-255)
• Set the value of the [Strobe] (0-20Hz)

3.4 DMX512 SETTINGS

• Enter the [ ADDRESS] mode to set the DMX ADDRESS.

3.5 ACTIVATING AUTO PROGRAMS

• Select the target [AUTO PROGRAM] program and press [ENTER] .
• Programs [AUTO0.01] to [AUTO.10] are fully pre-programmed and will not bealtered by changes in [EDIT ] mode.
• Programs [PR.01] to [PR.10] are fully pre-programmed and can be edited in [EDIT ] mode.

3.6 PERSONALITY

• Enter the [PERSONALITY] mode to select DMX mode: [HSIC] [SSP] [TOUR] . [TR16].

3.7 EDITING CUSTOM PROGRAMS

• Enter the [EDIT 1 mode to edit the custom programs [PR.011to [PR.10]
• Each custom program has 30 steps that can be edited.
• Each step allows the creation of a scene using [RED], [GREEN], [BLUE], [WHITE], [AMBER], [CYAN]. [UV], [STRBI, [TIME] & [FADE]

3.8 SPECIALSETTINGS

• [SETTING]…this menu allows the user to adjust key operation settings for this fixture.
• In order to reset custom modes to default values select [RESET].
• [COLOR] is for activate/unactivate the color calibration functions. When [RGBW] is selected, on RGB = 255,255,255, the color is displayed as calibrated in CALIB.C – RGBW. When[COLOR] is set[OFF], on RGB = 255,255,255, the RGB values are not adjusted and the output is most powerful. When [UC] is selected, the RGB output are adjusted to a standard preset universal color which balances fixtures from different generations
• Select [DIM1], [DIM2], [DIM3] or [DIM4] for different dimming speeds. ([DIM4]is the slowest dimming speed)
• [DMX ERROR] Choose[SAVE] in order to save the last DMX data incase of DMX signal error. Choose[BLACK] in order to blackout in case of DMX signal error.

3.9 ACTIVATE THE PASSWORD

• Enter the [KEY] mode to select whether the access password is on or off.
• When the fixture is setas PASS [ON1 , after 30 seconds or turn on the fixture next time, the fixture will need an access password to enter the display menu control.

Note: The factory access password is [UP] + [DOWN] + [UP] + [DOWN], then press [ENTER] to confirm the access.

3.10 BALANCE PARAMETERS AND CORRECTION MENU DISPLAY
Press [MENU 1 button to enter the password confirmation, to enter the correct password < UP + DOWN + UP + DOWN > Key, press the [MENU 1 in, the correct password will enter show submenu

• Enter the [CALIBRATION] to select white color of different color temperature.

• There are 12 pre-programmed White colors can be edited by using [RED], [GREEN], [BLUE] & [WHITE].
  Note: if CCT data is changed in [WHITE] from WT.01 to WT.12, CCT of according channel will be changed also

• Enter the [RGB to W] to adjust the RGB parameter to make different whites.

• When the new setting is activated, the DMX controller choose RGB = 255,255,255 the white color will be made by the actual RGB values onthe [RGBtoW]

• under [UC ] menu, press [ ENTER ] for color correction

• Press [ENTER] and choose [RED]. [GREN] [BLUE] [WHITE]. [AMBER] [CYAN]and [UV] for correction.

• Press [ MENU ] and return to menu, and keep value automatically.

3.13 INFO

• Press [ENTER ] and goto [ INFOJ ,you can check [ VERSION] .

3.12 WIRELESS

• Press [ENTER ] and enter [ WIRELESS ] ,choose [NO ] means no reset, choose [YES] means reset

USINGADMX512 CONTROLLER

4.1 CHANNELASSIGNMENT

• Note: This product have four DMX512 channel configuration: [HSIC], [SSP], [TOUR], [TR16].

HSIC

SSP

TOUR

251 255

| 6000K
10| | SPECIAL STROBE
0 9| NO FUNCTION
10 50| STROBE FROM (SLOD TO FAST. 0-25Hz )
61 100| NO FUNCTION
101 150| LIGHTNING STROBE
151 200| NO FUNCTION
201 255| RANDOM SROBE
CHANNEL| VALUE| FUNCTION
---|---|---
11| | AUTO
o ao| NO FUNCTION
41 50| ATUO1
51 60| ATUO2
81 70| ATUO3
71 80| ATUO4
81 90| ATUO5
91 100| ATUO6
101 110| ATUO7
111 120| An/08
121 130| ATUO9
131 140| ATU010
141 150| PROGRAMI
151 160| PROGRAM2
161 170| PROGRAM3
171 180| PROGRAM4
181 190| PROGRAMS
191 200| PROGRAMS
201 210| PROGRAM7
211 220| PROGRAMS
221 230| PROGRAM9
231 255| PROGRAM10
12| 0 255| AUTO SPEED ADJUSTMENT
13| | DIMMER SPEED
o 9| NO FUNCTION
10 29| OFF
30 69| DIM1
70 129| DIM2
130 189| DIM3
190 255| DIM4

TOUR

EASYPLAY REMOTE CONTROL

5.1 KEY FUNCTIONS

5.2 STATIC MODE

•  It can be static dimmer, choose static mode and enter into static dimmer
•  As instruction, it includes R+ R-,G+,G-,B+,B- W+ W- A+ A-,C+,C-,U+,U-, S+,8-,and [R+, R-1isforreddimmer, [G+, G-]is for green dimmer, [B+, B-1is forblue dimmer, [W+, W-1 is for white dimmer, [A+, A-1is for amber dimmer, [C+, C-1is forcyandimmer, [U+, U-]isfor UV dimmer, please refertoabove [RED] , [GREEN] , [BLUE] , [WHITE] , [AMBR] , [CYANI and [UV] to adjust

5.3 EFFECT CONTROLS

• Selectfrom [EFFECTKEY 011 to [EFFECTKEY 08] to play required play function (see section 2.3.3 for further information on how to patch [EFFECTKEYT )
• Select [SPEED (+)] or [SPEED (-)] toadjust speed play function.
• 1tis not possible to adjust the light level of the EFFECT programs using the [DIMMER] keys.

5.4 DIMMER

• There is a bottom for all color [RGBWACU] dimmer, lower right corner is a on/off bottom for fixture on/off operation.

OPERATION WITH WIRELESS DMX

6.1 When using this lighting fixture with W-DMX receiver installed inside, the fixture may be placed at a range of 200m from W-DMX transmitter

6.2 Select DMX from the menu.
6.3 Select ACTI from the menu and proceed to turn ON the WDMX If the WDMX receiver card is already paired with a WDMX transmitter then the fixture is ready for receiving DMX signal.
If the WDMX receiver card needs to be paired with a new WDMX transmitter, select YES from the / menu. The green signal indicator LED will not show which confirms that WDMX receiver card is unpaired and ready for new pairing..

6.4 By pressing the RESET button on W-DMX transmitter, transmitter will search for RESET lighting fixtures. During search transmitter green SIGNAL indicator will flash. After pairing with lighting fixture green SIGNAL indicator will display.

6.5 Once a lighting fixture has been paired with a W-DMX transmitter, the green SIGNAL indicator will display. Once a lighting fixture has been paired with a W-DMX transmitter, the lighting  fixture cannot be paired with another W-DMX transmitter.

If a lighting fixture requires pairing  with a new W-DMX transmitter, steps 5.3 and 5.4 must be repeated.

BATTERY CHARGING

7.1 FLIGHTCASE SPECIFICATIONS
Voltage: AC100-240V, 50,60Hz
Rated Power: 150W
Weight:9.8KG
Dimensions: 572x350x240mm

7.2:FLIGHTCASE WITH CHARGER

7.3 CHARGER SPECIFICATIONS

Voltage: AC100-240V, 50/60Hz
Output: DC24V, 1A
LED: <200mA

7.4: THEFLIGHTCASE MUST HAVE THE HOOD OPEN WHEN CHARGING.

7.5 IMPORTANT FACTS:
HOW TO CARE FOR YOUR BATTERY!

CHARGING

• DO NOT CHARGE FOR MORE THAN 24HRS
• RECHARGE WITHIN 3 DAYS OF USE
• CHARGE WITH FLIGHTCASE OPEN

STORING

• STORE WITH FULLLOAD
• TURN OFF AT BASE WHEN STORING FOR MORE THAN 7 DAYS
• STORE IN AN UPRIGHT POSITION

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>