PANORAMA ANTENNAS SW3-665 Ultra Wideband MiMo Antenna WMMG Range Instruction Manual
- June 12, 2024
- Panorama Antennas
Table of Contents
PANORAMA ANTENNAS SW3-665 Ultra Wideband MiMo Antenna WMMG Range
Product Information
Product: Ultra Wideband MiMo Antenna
Model: WMMG Range – SW3-665 v2
Contents:
- 1 x Antenna
- 1 x Desk Stand
- 2 x Wall Bracket Plates
- 1 x U-Bolt
- 1 x U-Bolt Plate
- 4 x Screws
- 4 x Plain Washers
- 4 x Spring Washers
- 2 x Nuts
Product Usage Instructions
Selecting a Position
- Check that all the contents are in the box.
- 1 x Antenna
- 1 x Desk Stand
- 2 x Wall Bracket Plates
- 1 x U-Bolt
- 1 x U-Bolt Plate
- 4 x Screws
- 4 x Plain Washers
- 4 x Spring Washers
- 2 x Nuts
- Select a position where the antenna can be directed towards the strongest network signal.
- Connect the antenna to your router or modem using the provided antenna adapter and coaxial cable.
- Ensure that your device is connected to the network and displaying the signal strength indicator.
- Note: Signal strength indication may be displayed either:
- Graphically with bars (where more bars indicate a better signal), or
- As a signal level value in dBm (e.g., -80), where lower negative numbers indicate a better signal (i.e., -71 is a stronger signal than -83).
Mounting the Antenna
- Mounting the antenna internally: To mount the antenna internally, use the supplied desk stand and follow the instructions at 5. DESK MOUNTING INSTRUCTIONS.
- Mounting the antenna externally: Mounting the antenna outside will provide optimum signal strength and data rates. Begin by following the instructions at 1.2 concerning position and orientating the antenna. Then follow 3. MAST
- MOUNTING INSTRUCTIONS or 4. WALL MOUNTING INSTRUCTIONS depending upon the equipment you have available.
Important Information
- RF Safety Note: Ensure that the antenna is mounted in such a way that no person is likely to be within a distance of 30 cm (12 inches) from the antenna during use.
- Electrical Caution: Parts of this antenna are electrical conductors. Contact with power lines can result in death or serious injury. The antenna and supporting mast must not be close to any power lines during installation, use, or removal. If the antenna is elevated and at risk from lightning strikes, it must be ensured that the antenna is mounted and earthed appropriately by a trained professional in accordance with the relevant standards.
- Waste Electrical Products: Waste electrical products should not be disposed of with household waste. All electronic products with the WEEE logo must be collected and sent to approved operators for safe disposal or recycling. Please recycle where facilities exist. Many electrical/electronic equipment retailers facilitate the Distributor TakeBack scheme for household WEEE. Check with your Local Authority or electronic retailers for designated collection facilities where WEEE can be disposed of for free.
- CE Note: RoHS 2 compliance is declared per Directive 2011/65/EU and its subsequent amendments with exemption 6.c applied. This product contains lead as an alloying element in a copper alloy containing up to 4% lead by weight. REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals, EC 1907/2006). This product contains Lead (CAS No. 7439-92-1) which is classified as an SVHC (Substance of Very High Concern) as being toxic to reproduction under Article 57c of REACH.
Selecting a Position
Check that all the contents are in the box
This should include:
- 1 x Antenna
- 1 x Desk Stand
- 2 x Wall Bracket Plates 1 x U-Bolt
- 1 x U-Bolt Plate
- 4 x Screws
- 4 x Plain Washers
- 4 x Spring Washers
- 2 x Nuts
Select Position
- For a good installation the antenna should be directed towards the strongest network signal. In order to achieve this follow the guide below:
- Connect the antenna to your router or modem with the antenna adapter (if applicable) and coaxial cable provided.
- Ensure that your device is connected to the network and displaying the signal strength indicator.
- With the antenna at selected location, rotate it in approximately 45 degree steps – in each position, you may need to wait for up to one minute to allow the signal strength indicator to update.
Note: Signal strength indication may be displayed either:
- a. Graphically with bars, (where more bars is a better signal), or
- b. As a signal level value in dBm (e.g. -80) – in this case, the lower the negative number, the better the signal, (i.e. -71 is stronger signal than -83).
Mounting the Antenna
- Mounting the antenna internally
- To mount the antenna internally use the supplied desk stand and follow the instructions at 5.
- DESK MOUNTING INSTRUCTIONS
- Mounting the antenna externally
- Mounting the antenna outside will provide optimum signal strength and data rates. Begin by following the instructions at 1.2 concerning position and orientating the antenna.
- Then follow 3. MAST MOUNTING INSTRUCTIONS or 4.
- WALL MOUNTING INSTRUCTIONS depending upon the equipment you have available.
Important Information
RF Safety Note – Ensure that the antenna is mounted in such a way that no person is likely to be within a distance of 30cms (12”) from the antenna during use.
RF Safety Note – Ensure that the antenna is used only as supplied the
co-axial cables should not be cut shorter or otherwise modified.
Electrical Caution – Parts of this antenna are an electrical
conductor. Contact with power lines can result in death or serious injury. The
antenna and supporting mast must not be close to any power lines during
installation, use or removal. If the antenna is elevated and at risk from
lightning strike it must be ensured that the antenna is mounted and earthed
appropriately by a trained professional in accordance with the relevant
standards.
Waste electrical products should not be disposed of with household waste. All
electronic products with the WEEE logo must be collected and sent to approved
operators for safe disposal or recycling. Please recycle where facilities
exist. Many electrical/electronic equipment retailers facilitate a
“Distributor Take- Back scheme”for household WEEE. Check with your Local
Authority or electronic retailers for designated collection facilities where
WEEE can be disposed of for free.
CE Note RoHS 2 compliance is declared per Directive 2011/65/EU and its
subsequent amendments with exemption 6.c applied. This product contains lead
as an alloying element in a copper alloy containing up to 4% lead by weight.
REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals,
EC 1907/2006). This product contains Lead (CAS No. 7439-92-1) which is
classified as an SVHC (Substance of Very High Concern) as being toxic to
reproductionunder Article 57c. of REACH.
Mast Mounting Instructions
- To Mast Mount this antenna you will need:
- 1 x Antenna
- 1 x U-Bolt
- 1 x U-Bolt Plate
- 2 x Washers
- 2 x Spring Washers
- 2 x Nuts
- Mast Mounting the antenna externally
- Ensure that the selected mounting location can be safely accessed with the equipment that you have available and mount the antenna so that it has at least 1 metre (3.3’) of clearance from all obstructions if possible. The antenna should not be mounted directly on to metal masts or poles. If the antenna must be mounted to such a surface it must be mounted at the lip of the roof or the very top of the pole such that the body of the antenna is elevated clear of the metal surface.
- Ensure a safe connection
- Secure the antenna in place and waterproof the exposed connections. Fully tighten the mounting hardware. If exposed the RF connector joint should be waterproofed with a weatherproof electrical tape (self amalgamating type is recommended) allowing a significant overlap of each turn and ensuring that the overlap is in the opposite direction to predicted water fall.
Wall Mounting Instructions
- To Wall Mount this antenna you will need:
- 1 x Antenna
- 2 x Wall Bracket Plates
- 4 x Screws
- 4 x Washers
- 4 x Spring Washers
- 2 x Nuts
- Fix the mounting bracket to the external wall or other flat surface using suitable screws and wall plugs (not supplied).
- Fix the mounting bracket to the antenna using the washers and screws supplied.
- Fix the antenna to the wall mounting bracket
- Secure the antenna in place and waterproof the exposed connections. Fully tighten the mounting hardware. If exposed the RF connector joint should be waterproofed with weatherproof electrical tape (self-amalgamating type is recommended) allowing a significant overlap of each turn and ensuring that the overlap is in the opposite direction to the predicted waterfall.
Desk Mounting Instructions
- To Desk Mount this antenna you will need
- 1 x Antenna
- 1 x Desk Mount
- Using the Antenna Internally
- When using the antenna internally, take care to ensure that the antenna or cables do not cause a trip hazard. The antenna can be fitted to the supplied desk stand for internal use. Optimum performance will be achieved with the antenna facing a window in the direction of best network signal strength.
- Mounting and dismounting the antenna to the desk stand
- Once you have determined the desired mounting location and orientation you can mount and dismount the antenna to the supplied desk stand following the steps below.
- Mounting the Antenna
- Hold the antenna cable securely upwards against the back of the antenna. Push the mounting foot of the antenna down into the groove in the base so that the mounting holes sit flush with the pegs in the base as shown.
- Holding the antenna and base securely push the antenna back into the base until the pegs locate.
- Dismounting the Antenna
- Grip the base securely from below and the antenna at the top edge.
- Pull the top of the antenna away from the base stand whilst lightly squeezing the base in order to pivot the foot of the antenna out of the trough in the desk stand as shown.
- Once the foot of the antenna is unlocked from the desk stand pull the antenna forwards and upwards from the base freeing
Contact Information
Panorama Antennas Ltd
- Head Office – United Kingdom
- 61 Frogmore, Wandsworth, London, SW18 1 HF
- sales@panorama-antennas.com
- +44 (0)20 8877 4444
Panorama Antennas Inc
- USA
- 1551 Heritage Parkway, Suite 101, Mansfield, TX, 76063
- sales.nam@panorama-antennas.com
- +1 817-539-1888
- Panorama Antennas Pty Ltd
Australia
- Unit 1, 5 Jaggs Way, Kardinya, WA 6163
- sales.apac@panorama-antennas.com
- +61 406 812 364
Panorama Antennas SAS
- France
- 16 Allée des Acacias, 33700 Mérignac
- fr.sales@panorama-antennas.com
- +33 554 070 436
Panorama Antennas Pte Ltd
- Singapore
- Space@ Tampines, 18 Tampines Industrial Crescent, 528605
- sales.sea@panorama-antennas.com
- +65 9155 4194
Panorama Antennas Ltd
- Germany
- de.sales@panorama-antennas.com
- +49 2303 902 88 00
- www.panorama-antennas.com
Documents / Resources
|
PANORAMA ANTENNAS SW3-665 Ultra Wideband MiMo Antenna WMMG
Range
[pdf] Instruction Manual
SW3-665 Ultra Wideband MiMo Antenna WMMG Range, SW3-665, Ultra Wideband MiMo
Antenna WMMG Range, Wideband MiMo Antenna WMMG Range, MiMo Antenna WMMG Range,
Antenna WMMG Range, WMMG Range, Range
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>