BOSS SDE-3000D Dual Digital Delay Pedal User Guide

BOSS SDE-3000D Dual Digital Delay Pedal

Product Information

The SDE-3000D is a stereo digital delay unit that features two digital delays, namely DIGITAL DELAY 1 (DDL1) and DIGITAL DELAY 2 (DDL2). It is designed to provide high-quality delay effects for audio signals. The unit has various input and output options, including mono and stereo configurations, as well as support for external MIDI devices.

Product Usage Instructions

Connecting Your Equipment:

• To prevent malfunction and equipment failure, always turn down the volume and turn off all units before making any connections.
• For mono delay, use the MONO IN/OUT configuration with L/MONO input and L/MONO output.
• The INPUT L/MONO, CTL 4, and 5 jacks are only for use with the GA-FC foot controller.
• The STEREO IN/OUT configuration allows for stereo input and output, with the direct sound and effect sound mixed.
• Use only the specified expression pedal to avoid malfunction and damage to the unit.
• If necessary, connect an external earth or ground.
• Use TRS/TRS or TRS/MIDI connecting cables to connect the unit to an external MIDI device.
• Connect your computer using a commercially available USB cable that supports USB 2.0. Do not use a cable designed only for charging.

Turning the Power On:

• Before turning the unit on/off, always turn the volume down to avoid any sudden loud sound.
• Connect the AC adaptor to the DC IN jack to turn on the power.
• Turn on any connected devices first, followed by your guitar amp and related equipment.
• When turning off the power, do it in reverse order.
• Unsaved data is lost when the power turns off, so make sure to save any important data before turning off the unit.

For more detailed information, refer to the Reference Manual available on the Roland website.

The SDE-3000D features two digital delays (SDE-3000) that have been extended to stereo specifications.
DIGITAL DELAY 1 (DDL1)/DIGITAL DELAY 2 (DDL2)

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).
After reading, keep the document(s) where it will be available for immediate reference.

Connecting Your Equipment

(Rear Panel/Side Panel)

To prevent malfunction and equipment failure, always turn down the volume, and turn off all the units before making any connections.

MONO IN/OUT

This produces mono delay with L/MONO input and L/MONO output.

STEREO IN/OUT

The sound is input in stereo, and the direct sound and the effect sound are mixed and output.

Refer to “Configuring the Settings of This Unit (SETUP)”for how to edit the input/output settings.

• Use only the specified expression pedal. By connecting any other expression pedals, you risk causing malfunction and/or damage to the unit.

• Connect this to an external earth or ground if necessary.
  MIDI (OUT/IN) jacks
  Use TRS/TRS connecting cables (BCC-1-3535 or BCC-2-3535, sold separately) or TRS/MIDI connecting cables (BMIDI-5-35, BMIDI-1-35 or BMIDI-2-35, sold separately) to connect this unit to an external MIDI device.
  USB port (USB Type-C®)
  Connect your computer using a commercially available USB cable that supports USB 2.0.

• Do not use a USB cable that is designed only for charging a device. Chargeonly cables cannot transmit data.

Turning the Power On

• Before turning the unit on/off, always be sure to turn the volume down. Even with the volume turned down, you might hear some sound when switching the unit on/off. However, this is normal and does not indicate a malfunction.

1. Connect the AC adaptor to the DC IN jack.
   This turns the power on.

2. Turn on any connected devices first, and then your guitar amp and related equipment.

   • Do this in reverse order when turning off the power.
   • Unsaved data is lost when the power turns off. Before turning the power off, save the data that you want to keep.
   • The bank and memory number that you were using when you turned the power off are stored in memory, and are recalled when you turn the unit back on.

Play Mode

The unit enters “play mode” after you turn on the power and the unit is ready to be played.
The TIME/FEEDBACK/OUT/RATE/DEPTH values for the delay are shown in the display, and the indicators light to show which bank and memory number is selected.

You can switch between display modes by pressing the [ ] [ ] buttons while in play mode.

Basic Operations

(Top Panel)

Area Controller/Explanation

1

Control

| [TIME] button: Adjusts the delay time.

[FEEDBACK] button: Adjusts the delay feedback level. A setting of zero produces a single delay.

[OUT] button: Adjusts the output level for the delay sound.

[RATE] button: Adjusts the cycle of the delay modulation.

[DEPTH] button: Adjusts the depth of the delay modulation. A setting of zero turns the modulation off.

MEMO

Long-press a button to make its value change rapidly.

---|---
2

Memory

| [1]–[4] buttons: Selects the memories.

[BANK A] button / [BANK B] button: Switches between memory bank A and B.

3

Delay settings

| [FILTER] button: Delay filter. If this is on, a natural- sounding effect is obtained when you’re using the delay as an echo.

[TIME x 2] button: Switches between delay ranges.

Delay time

Off ( x 1) 0–1500 ms

On ( x 2) 0–3000 ms

[DELAY PHASE] button: Inverts the phase of the delay sound.

[MOD] button: Turns the modulation on/off.

[FEEDBACK PHASE] button: Inverts the phase of the delay sound’s feedback.

[DIGITAL DELAY  1] button (DDL1) / [DIGITAL DELAY

2] button (DDL2): Switches between DDL1 and DDL2

parameter view.

[SETUP] button: Configures the system parameters. Long-press the button to turn the lock on/off. Other button operations are disabled when the lock feature is enabled.

4

Switches

| [DDL 1] switch / [DDL 2] switch: Switches the DIGITAL DELAY 1/2 on and off.

Press the [DDL 1] and [DDL 2] switches together to select the previous memory.

[TAP/CTL 1] switch: Press this switch in specific intervals to set the delay time. You can also use the functions assigned in SETUP.

Press the [DDL 2] and [TAP/CTL 1] switches together to select the next memory.

Configuring the Settings of This Unit

(SETUP)

Here’s where you set the system parameters.
As an example, the following shows how to change the IN/OUT settings.

1. Press the [SETUP] button.
   The parameter to set is shown in the display.

2. Press the [SETUP] (ENTER) button.
   The display indicates “ .
   MEMO
   Press the [TIME] button to select other parameters.
   For details, refer to “Reference Manual” (Roland website).

3. Use the [DEPTH] buttons to change the value.

4. To exit the settings, press the [â] (EXIT) button several times to return to play mode.

Saving to Memory

(WRITE)

1. Long-press the [BANK A] (WRITE) button.
   The write menu appears.

2. Press the [SETUP] (ENTER) button.

3. To change the write destination, use the [DEPTH] button to select a memory number.
   Press the [â] (EXIT) button if you want to cancel and return to the write menu.

4. Press the [BANK A] (WRITE) button to save the memory.
   When the memory is finished saving, the unit switches to the write destination memory and returns to play mode.

Attaching the Rubber Feet

You can attach the rubber feet (included) if necessary.
Attach them in the locations shown in the illustration.

• Using the unit without rubber feet may damage the floor.
• When turning the unit over, be careful so as to protect the buttons and knobs from damage. Also, handle the unit carefully; do not drop it.

Reference Manual (Roland Website)
Refer to the website listed below for detailed documentation on how to operate this unit.
https://roland.cm/sde3000d_om

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>