BOSS SDE-3000EVH Dual Digital Delay Pedal User Guide

BOSS SDE-3000EVH Dual Digital Delay Pedal

Product Information

The SDE-3000EVH is a stereo digital delay unit featuring two digital delays (SDE-3000) that have been extended to stereo specifications. It offers various input and output options, including direct output, stereo output, and MIDI connectivity. The unit also has a setup menu where you can configure system parameters.

Connecting Your Equipment (Rear Panel/Side Panel)
To prevent malfunction and equipment failure, always turn down the volume and turn off all the units before making any connections. For detailed cabling methods and diagrams, please refer to the SDE-3000EVH Player’s Guide.

Play Mode
The unit enters play mode after turning on the power. The display shows the TIME/FEEDBACK/OUT/RATE/DEPTH values for the delay, and the indicators light up to indicate the selected bank and memory number.

Configuring the Settings of This Unit (SETUP)
The setup menu allows you to set system parameters. Here’s an example of how to change the IN/OUT settings:

1. Press the [SETUP] button.
2. Use the display to navigate and select the desired parameter.
3. Press the [SETUP] (ENTER) button to confirm the selection.

Connecting MIDI and USB
Use TRS/TRS or TRS/MIDI connecting cables to connect the unit to an external MIDI device. To connect a computer, use a USB cable that supports USB 2.0. Avoid using USB cables designed only for charging as they cannot transmit data.

Product Usage Instructions

Turning the Power On

1. Connect the AC adaptor to the DC IN jack to turn on the power.
2. Turn on any connected devices first, followed by your guitar amp and related equipment.
3. To turn off the power, follow the same order in reverse. Note that unsaved data will be lost when the power turns off, so save any important data before turning off the unit.

Remember to always turn down the volume before turning the unit on/off to avoid any sudden loud sound.

Note:
The user manual contains additional important information about using the unit safely and other important notes. Please refer to those sections for a complete understanding of the product usage.

Startup Guide
EVH, the EVH logo, and the Stripe Design © used under license from EVH Brands, LLC.

The SDE-3000EVH features two digital delays (SDE-3000) that have been extended to stereo specifications. DIGITAL DELAY 1 (DDL1)/DIGITAL DELAY 2 (DDL2)

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet). After reading, keep the document(s) where it will be available for immediate reference.

Connecting Your Equipment

Connecting Your Equipment (Rear Panel/Side Panel)

• To prevent malfunction and equipment failure, always turn down the volume, and turn off all the units before making any connections.
• For a comprehensive group of all potential cabling methods and diagrams, please refer to the “SDE-3000EVH Players Guide”.

DIRECT OUT + STEREO OUT (factory settings)
The direct sound without delay applied is output from the DIRECT jack, and the effect sound is output in stereo from the EFX L and R jacks.

STEREO IN/OUT
The sound is input in stereo, and the direct sound and the effect sound are mixed and output.

• Refer to “Configuring the Settings of This Unit (SETUP)”for how to edit the input/output settings.
• Use only the specified expression pedal. By connecting any other expression pedals, you risk causing malfunction and/or damage to the unit.
• Connect this to an external earth or ground if necessary.
• Do not use a USB cable that is designed only for charging a device. Chargeonly cables cannot transmit data.

Turning the Power On

Before turning the unit on/off, always be sure to turn the volume down. Even with the volume turned down, you might hear some sound when switching the unit on/off. However, this is normal and does not indicate a malfunction.

1. Connect the AC adaptor to the DC IN jack. This turns the power on.
2. Turn on any connected devices first, and then your guitar amp and related equipment.
   • Do this in reverse order when turning off the power.
   • Unsaved data is lost when the power turns off. Before turning the power off, save the data that you want to keep.
   • The bank and memory number that you were using when you turned the power off are stored in memory, and are recalled when you turn the unit back on.

Play Mode

The unit enters “play mode” after you turn on the power and the unit is ready to be played. The TIME/FEEDBACK/OUT/RATE/DEPTH values for the delay are shown in the display, and the indicators light to show which bank and memory number is selected.

You can switch between display modes by pressing the [ ] [ ] buttons while in play mode.

When you switch between banks/memories, the bank and memory number is shown momentarily.

Bank/Memory

| Shows the bank and memory number.
|

Basic Operations

Top Panel

Configuring the Settings of This Unit

SETUP
Here’s where you set the system parameters. As an example, the following shows how to change the IN/OUT settings.

1. Press the [SETUP] button.
   The parameter to set is shown in the display.

2. Press the [SETUP] (ENTER) button.
   The display indicates “in”.
   MEMO

   • Press the [TIME] button to select other parameters.
   • For details, refer to “Reference Manual” (Roland website).

3. Use the [DEPTH] buttons to change the value.
   MEMO
   When “in” (Input Setting) is set to “Nono” (MONO), the send/return circuit is enabled.

4. To exit the settings, press the [ ] (EXIT) button several times to return to play mode.

Saving to Memory

WRITE

1. Long-press the [BANK A/B] (WRITE) button.
   The write menu appears.

2. Press the [SETUP] (ENTER) button.

3. To change the write destination, use the [DEPTH] button to select a memory number.
   Press the [ ] (EXIT) button if you want to cancel and return to the write menu.

4. Press the [BANK A/B] (WRITE) button to save the memory.
   When the memory is finished saving, the unit switches to the write destination memory and returns to play mode.

Attaching the Rubber Feet

You can attach the rubber feet (included) if necessary. Attach them in the locations shown in the illustration.

• Using the unit without rubber feet may damage the floor.
• When turning the unit over, be careful so as to protect the buttons and knobs from damage. Also, handle the unit carefully; do not drop it.

Reference Manual / Players Guide (Roland Website)
Refer to the website listed below for detailed documentation on how to operate this unit. https://roland.cm/sde3000evh_om.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>