BOSCH SMS44DW01T Dishwasher Instruction Manual

BOSCH SMS44DW01T Dishwasher

Product Information

The product being referred to in the user manual is a dishwasher. It is a convenient and efficient appliance for cleaning tableware. The manual provides information on water hardness settings, special salt usage, rinse aid usage, detergent usage, program data, and maintenance instructions.

Water Hardness Settings
The dishwasher has a water softening system that can be adjusted based on the hardness of the water supply. The manual provides a table with different water hardness ranges and their corresponding setting values. Users can select the appropriate setting based on the water hardness in their area.

Special Salt Usage
To prevent damage to the dishwasher, special salt needs to be added to the dispenser before starting a program. The manual provides step-by-step instructions on how to add the special salt, including unscrewing the dispenser lid, filling it with water, and setting the desired water hardness value using the program buttons.

Rinse Aid Usage
Rinse aid is another additive that enhances the performance of the dishwasher. The manual explains how to add rinse aid to the dispenser, including pressing the catch on the dispenser lid, filling it up to the max mark, and closing the lid securely.

Detergent Usage
The manual instructs users to add detergent to the designated detergent dispenser in the dishwasher. It provides specific measurements for different types of detergents and emphasizes the importance of closing the lid properly.

Program Data
The manual includes a table with program data measured according to European standard EN 60436. This data includes the duration of each program, energy consumption in kWh, and water consumption in liters. It also mentions that these figures may vary depending on
the selected program and additional functions, as well as the use of rinse aid.

Product Usage Instructions

1. Load the tableware into the dishwasher, ensuring it is suitable for dishwasher use and removing large food remnants.
2. Add the appropriate amount of detergent to the dry detergent dispenser.
3. Switch on the dishwasher.
4. Select the desired program.
5. Start the program.
6. At the end of the program, remove the clean tableware from the dishwasher.
7. To cancel a program, press and hold the cancel button for approximately 3 seconds. The program will be cancelled and end after about 1 minute.
8. After each wash, check the filters for residue.
9. To clean the filters, turn the coarse filter anticlockwise and remove it. Pull down the micro filter to remove it. Clean the filter elements under running water. Reassemble the filter system and insert it back into the dishwasher.
10. Clean the spray arms by unscrewing the upper spray arm and pulling it down. Rinse it under running water and reattach it.

Short and handy…
… everything your dishwasher needs.
Before using for the first time, make sure you read both the operating and the installation instructions.

Overview of water hardness settings

You can find an overview of the water hardness values that can be selected here.
A table of country-specific units can be found in the instruction manual.

Setting the water softening system

1. Press  ⁠.
2. To open the basic settings, press  for approx. 3 seconds.
   • The display shows Hxx.
   • The display shows Set ⁠.
3. Press Start repeatedly until the right water hardness has been set.
4. To save the settings, press   for 3 seconds.

Programmed

The programme data has been measured in the laboratory according to European standard EN 60436.
The consumption figures depend on the programme and additional function selected.
The running time will change if the rinse aid system is switched off or rinse aid needs to be added.

1. half standard load

Adding special salt
To avoid damage to the appliance, only add special salt to the dispenser for special salt just before the programmed starts.

1. Unscrew the lid of the dispenser for special salt and remove.
2. On initial start-up: Fill the dispenser right up with water.
3. Add the special salt to the dispenser. The water in the dispenser is displaced and forced out. Never add detergent.
4. Place the lid back on the dispenser and turn to close.

Adding rinse aid

1. Press the catch on the lid of the dispenser for rinse aid and lift ⁠.

2. Add rinse aid up to the max mark.

3. Close the lid of the dispenser for rinse aid.
   The lid clicks into position.

Adding detergent

1. Add the detergent to the dry detergent dispenser.

2. Close the lid of the detergent dispenser.
   The lid clicks into position.

How to use your appliance

1. Load the tableware.
   Only clean tableware that is suitable for dish-washers.
   Remove large remnants of food from the tableware.
   Check that the spray arms can rotate freely.

2. Add detergent.

3. Switch on the appliance ⁠.

4. Select the programmed.

5. Start the programmed

6. Remove the tableware at the end of the programmed.

7. To cancel the programmed, press for approx. 4 seconds.
   The programmed is cancelled and ends after approx. 1 minute.

Cleaning filters

1. After each wash check the filters for residue.

2. Rotate the spray arm to the side to make room for filter cleaning.

3. Turn the coarse filter anticlockwise and remove the filter system ⁠.
   

4. Pull down the micro filter to re-move.

5. Press the locking catches together and lift the coarse filter out ⁠.

6. Clean the filter elements under running water.

7. Re-assemble the filter system.

8. Insert the filter system into the appliance and turn the coarse filter clockwise.
   Make sure that the arrow markings match up.
   The spray arm will automatically return to the correct position when starting, so it is not necessary to reposition the spray arm to the front.

Cleaning the spray arms

1. Unscrew the upper spray arm and pull down to remove ⁠.

2. Position the lower spray arm as shown , grip in the middle and pull up to remove

3. Check the outlet nozzles on the spray arms for blockages under running water and remove any foreign bodies.

4. Insert the lower spray arm.

   • The spray arm clicks into position.

5. Insert the upper spray arms and screw firmly in place.

Clean wastewater pump

1. Disconnect the appliance from the power supply.

2. Remove the filter system.

3. Scoop out any water.

4. Prize off the pump cover using a spoon and grip it by the crosspiece.

5. Lift the pump cover inwards at an angle and remove.

6. Remove any remnants of food and foreign bodies in the area of the impeller.

7. Insert the pump cover and press down ⁠.
   The pump cover clicks into position.

8. Install the filter system.

Troubleshooting

Fault
E:3-200 or indicator for water supply lights up.

Cause and troubleshooting
Supply hose is kinked.

• Install the supply hose without kinks.

Water tap is turned off.

• Turn on the water tap.

Water tap is jammed or furred up.

• Turn on the water tap.
  The flow rate must be at least 10 l/min when the water supply is open.

The filters in the water connection of the supply or Aqua Stop hose are blocked.

1. Switch off the appliance.

2. Pull out the mains plug.

3. Turn off the water tap.

4. Unscrew the water connection.

5. Remove the filter from the sup-ply hose

6. Clean the filter.

7. Re-insert the filter in the supply hose.

8. Screw the water connection back on.

9. Check the water connection for leaks.

10. Restore the power supply.

11. Switch the appliance on.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>