metabo SSD 18 LT 200 BL Cordless Impact Driver Instruction Manual

metabo SSD 18 LT 200 BL Cordless Impact Driver

Product Information

• Model: SSD 18 LT 200 BL
• Serial Number: 02397…
• Voltage: 18 V
• No-load Speed: 0 – 3050 rpm
• Impact Rate: 3750 bpm
• Chuck Size: 1/4″ (6.35 mm)
• Max Torque (M1): 1.6 Nm (3.5 in-lbs)
• Max Torque (M2): 40 Nm (354 in-lbs)
• Max Torque (M3): 150 Nm (1328 in-lbs)
• Weight: 1.5 kg (3.3 lbs)
• Vibration Level (ah / Kh): 14.0 m/s2
• Sound Pressure Level (LpA / KpA): 97 dB(A)
• Sound Power Level (LWA / KWA): 108 dB(A)

  ---

Product Usage Instructions

1. Before fitting the battery pack, make sure that the tool is switched off.
2. Ensure that the work area is clear of power cables, gas lines, or water pipes using a metal detector.
3. Secure the workpiece to prevent slipping or rotation, such as by using screw clamps.
4. Use only screwdriving bits suitable for the impact driver.
5. When driving in long screws, be careful to avoid slipping.
6. Mount the machine on the screw only when it is switched off.
7. Wear ear protectors when working for long periods of time to protect your hearing.
8. In case of battery fluid leakage, rinse your skin immediately with plenty of water. If it comes into contact with your eyes, wash them with clean water and seek medical attention.
9. If the machine is defective, remove the battery pack from the machine.
10. Protect battery packs from water, moisture, and fire.
11. Do not use faulty or deformed battery packs, open battery packs, or touch/short circuit battery pack contacts.
12. Be aware that slightly acidic, flammable fluid may leak from defective Li-Ion battery packs.
    Please refer to the user manual for more detailed instructions and safety information.

Declaration of Conformity

We hereby declare under our sole responsibility that these cordless impact drivers, identified by type and serial number 1), meet all relevant requirements of directives 2) and standards 3). Technical documents for 4) – see page 3.
For UK only:
We as manufacturer and authorized person to compile the technical file, see 4) on page 3, hereby declare under sole responsibility that these cordless impact wrench, identified by type and serial number 1) on page 3, fulfill all relevant provisions of following UK Regulations S.I. 2016/ 1091, S.I. 2008/1597, S.I. 2012/3032 and Designated Standards EN 62841-1:2015, EN 62841-2-2:2014, EN IEC 63000:2018.

1. 2014/30/EU, 2006/42/EC, 2011/65/EU

2. EN 62841-1:2015, EN 62841-2-2:2014, EN IEC 63000:2018 2021-04-21, Bernd Fleischmann
   Direktor Produktentstehung & Qualität (Vice President Product Engineering & Quality)

3. Metabowerke GmbH – Metabo-Allee 1 – 72622 Nuertingen, Germany

Specified Conditions of Use

• The impact driver is suitable for driving in and removing screws.
• The user bears sole responsibility for any damage caused by inappropriate use.
• Generally accepted accident prevention regulations and the enclosed safety information must be observed.

General Safety Information

• For your own protection and for the protection of your power tool, pay attention to all parts of the text that are marked with this symbol!
• WARNING – Read the operating instructions to reduce the risk of injury.
• WARNING – Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
• Keep all safety instructions and information for future reference.
• Always include these documents when passing on your power tool.

Special safety instructions

• Hold the power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
• Remove the battery pack from the machine before making any adjustments, changing tools, maintaining or cleaning.
• Make sure that the tool is switched off before fitting the battery pack.
• Ensure that the spot where you wish to work is free of power cables, gas lines or water pipes (e.g. using a metal detector).
• Secure the workpiece to prevent slipping or rotation (e.g. by securing with screw clamps).
• Protect battery packs from water and moisture!
• Do not expose battery packs to fire!
• Do not use faulty or deformed battery packs!Do not open battery packs!
• Do not touch or short circuit battery pack contacts! A slightly acidic, flammable fluid may leak from defective Li-Ion battery packs!
• If battery fluid leaks out and comes into contact with your skin, rinse immediately with plenty of water. If battery fluid leaks out and comes into contact with your eyes, wash them with clean water and seek medical attention immediately!
• If the machine is defective, remove the battery pack from the machine.
• Only screwdriving bits suitable for the impact drivers must be used.
• Take care when driving in long screws – risk of slipping.
• Mount the machine on the screw only when it is switched off.
• Wear ear protectors when working for long periods of time. High noise levels over a prolonged period of time may affect your hearing.
• LED light (7): do not observe the LED radiation directly with optical instruments.
• Transport of Li-Ion battery packs:
• The shipping of Li-Ion battery packs is subject to laws related to the carriage of hazardous goods (UN 3480 and UN 3481). Inform yourself of the currently valid specifications when shipping Li-Ion battery packs. If necessary, consult your freight forwarder.
• Certified packaging is available from Metabo.
• Only send the battery pack if the housing is intact and no fluid is leaking. Remove the battery pack from the machine for sending. Prevent the contacts from short-circuiting (e.g. by protecting them with adhesive tape).

Reducing dust exposure:

WARNING – Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and – arsenic and chromium from chemically treated

lumber.

• Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks that are specially
• designed to filter out microscopic particles.
• This also applies to dust from other materials, such as some timber types (like oak or beech dust), metals, asbestos. Other known diseases are e.g. allergic reactions, respiratory diseases. Do not let dust enter the body.
• Observe the relevant guidelines and national regulations for your material, staff, application and place of application (e.g. occupational health and safety regulations, disposal).
• Collect the particles generated at the source, avoid deposits in the surrounding area.
• Use suitable accessories for special work. In this way, fewer particles enter the environment in an uncontrolled manner.
• Use a suitable extraction unit.

Reduce dust exposure with the following measures:

1. Square attachment for 1/2“ tools *
2. Hexagon socket attachment for hexagon screwdriving bits*
3. Locking sleeve*
4. Rotation selector switch / Transporting safety device
5. Trigger
6. Handle (gripping surface)
7. LED light For working in badly lit areas. The LED light lights up when the machine is switched on.
8. Button for speed and tightening torqueselection
9. Battery pack *
10. Battery pack release button
11. Capacity indicator button *
12. Capacity and signal indicator *
13. Belt hook (attach as shown) *

depending on the features / model

Initial Operation/Setting

Remove the battery pack from the machine
before any adjustment or maintenance is
carried out. Make sure that the tool is switched off
before fitting the battery pack.
6.1 Battery pack
Charge the battery pack (9) before use. Recharge
the battery pack if performance diminishes.
Instructions on charging the battery pack can be
found in the operating instructions of the Metabo
charger.
Ion battery packs “Li-Power, LiHD“ have a capacity and signal indicator (12):

• Press the button (11), the LEDs indicate the charge level.
• The battery pack is almost empty and must be recharged if one LED is flashing. Removing:

Press the battery pack release button (10) and pull the battery pack (9) forwards.

Inserting:

• Slide in the battery pack (9) until it engages.
• Setting the direction of rotation, engaging the transporting safety device (switch-on lock) Only operate the rotation selector switch / transporting safety device (4) when the motor is at standstill!

Actuate the rotation selector switch / Engage the transportation lock (4).

• R = Clockwise setting (drive in screws)
• L = Anti-clockwise setting (undo screws)
• 0 = middle position: transportation safety device (Switch-on lock) set

Switching on and off

• Switching on: press the trigger switch (5).
• Switching off: Release the trigger (5).

Speed / tightening torque

The speed and tightening torque are connected directly. The lower the speed, the lower the tightening torque.
The tightening torque is influenced in two ways:

Select maximum tightening torque.
You can select one of three tightening torque settings by pressing the button (8). The maximum tightening torques can be found in the table on page 3 (M1, M2, M3).
The lights indicate which setting is selected.

• 1 = min. tightening torque
• 2 = medium tightening torque
• 3 = max. tightening torque

Stepless adjustment of the tightening torque:

The speed and tightening torque can be adjusted steplessly in any torque setting by pressing the trigger (5) firmly or lightly, thus adapting to working conditions.
Recommendation: determine the correct setting by carrying out trial screwdriving.

Changing SSD screwdriving bits

Inserting screwdriving bit: Slide locking sleeve (3) forward and insert screwdriving bit as far as the stop. Release locking sleeve (3) . Pull on the screwdriver bit to check that it is correctly seated. Removing screwdriving bit: Slide locking sleeve (3) forward and remove screwdriving bit. Only use screwdriving bits with such plug-in ends:

The screwdriving bit used must match the
screw.
Damaged screwdriving bits must not be used.
Change screwdriving bit for SSW

• Inserting screwdriving bit: Fit the tool on the square attachment (1) until the limit stop.
• Removing screwdriving bit: Pull the tool from the square attachment (1).
• The screwdriving bit used must match thescrew.
• Damaged screwdriving bits must not be used

Use

• Mount the machine on the screw, ensuring it is aligned straight.

• The screwdriving process consists of 2 parts: insert screw and tighten screw with the impact mechanism.

• The tightening torque depends on the impact duration.

• With an impact duration of approx. 5 seconds, the maximum tightening torque has been reached.

• The torque curve depends on the type of application:

• With a hard screwdriving application (screw couplings in a hard material such as metal), maximum tightening torque is already reached after a short impact duration (a).

• With a soft screwdriving application (screwcouplings in a soft material such as wood), a longer impact duration (b) is required.

• Recommendation: determine the correct impact duration by carrying out trial screwdriving.
  Caution! For small screws the maximum torque can be reached already after 0.5 seconds impact duration.

• This is why the duration of the screwdriving process must be monitored exactly.

• Set a (8) suitable tightening torque using the button (see chapter 6.4).

• Adjust the tightening torque by pressing firmly or lightly on the trigger (5), ensuring that the screw is not damaged or that the screw head does not tear off.

Accessories

Use only original Metabo or CAS (Cordless Alliance System) battery packs and accessories. Use only accessories that fulfil the requirements and specifications listed in these operating instructions.
See page 4.

• A Chargers
• B Battery packs with different capacities Use only battery packs with voltage suitable for your power tool.
• C Screwdriving bits

For a complete range of accessories, see www.metabo.com or the catalogue.

Repairs

Repairs to electrical tools must ONLY be carried out by qualified electricians! Contact your local Metabo representative if you have Metabo power tools requiring repairs. For addresses see www.metabo.com. You can download a list of spare parts from www.metabo.co

Environmental Protection

Observe national regulations on environmentally compatible disposal and on the recycling of disused machines, packaging and accessories. Battery packs may not be disposed of with regular waste. Return faulty or used battery packs to your Metabo dealer!
Do not allow battery packs to come into contact with water!
Only for EU countries: never dispose of power tools in your household waste! According to European Directive 2012/19/EU on Waste from Electric and Electronic Equipment and implementation in national law, used power tools must be collected separately and recycled in an environmentally-friendly manner. Discharge the battery pack in the power tool before disposal. Prevent the contacts from short-circuiting (e.g. by protecting them with adhesive tape).

Technical Specifications

Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.

• U =Voltage of battery pack
• n0 =No-load speed
• S =impact frequency
• H =machine tool holder
• m =weight (with the smallest battery pack)
• M1 = min. tightening torque
• M2 = medium tightening torque
• M3 = max. tightening torque

Measured values determined in conformity with EN 62841.
Permitted ambient temperature during operation: -20 °C to 50 °C (limited performance with temperatures below 0 °C). Permitted ambient temperature for storage: 0 °C to 30 °C direct current
The technical specifications quoted are subject to tolerances (in compliance with relevant valid standards).

Emission values

These values make it possible to assess the emissions from the power tool and to compare different power tools. The actual load may be higher or lower depending on operating conditions, the condition of the power tool or the accessories used. Please allow for breaks and periods when the load is lower for assessment purposes. Arrange protective measures for the user, such as organisational measures based on the adjusted estimates.
Vibration total value (vector sum of three directions) determined in accordance with EN 62841:

• ah = Vibration emission value (screwdriving with impact)
• Kh = uncertainty (vibration)
• Typical A-weighted sound levels:
• LpA = sound-pressure level
• LWA = acoustic power level
• KpA, KWA = Uncertainty (noise level)
• Wear ear protectors

www.metabo.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>