Yueqing City Full Imp Exp WFU236 Smart Wi-Fi USB Wall Outlet User Manual

Yueqing City Full Imp Exp WFU236 Smart Wi-Fi USB Wall Outlet

PRODUCT OUTLINE

INDICATOR LIGHT STATUS

MANUAL OPERATION OF THE WALL OUTLET

Pairing Setup
Press and hold the ON/OFF switch for 5s until the Wi-Fi indicator light blinks orange quickly to initiate default configuration; press and hold the switch for 5s again until the Wi-Fi indicator light blinks orange slowly to initiate AP configuration.

SAFETY INFORMATION

WARNINGS AND CAUTIONS

• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF THE POWER AT THE CIRCUIT BREAKER OR FUSE AND TEST THAT THE POWER IS OFF BEFORE WIRING!
• To be installed and/or used in accordance with appropriate electrical codes and regulations. If you are not sure about any part of these instructions, consult an electrician. This device CANNOT be used for separate feed applications. I the outlet you are replacing has the top and bottom outlets controlled by separate circuit breakers, you cannot use this device. Use this device with copper or copper-clad wire only.

INSTALLATION

Tools You’ll Need

• Screwdriver
• Pliers
• Electrical tester

Caution

• Make sure that the power at the circuit breaker is off before wiring.
• A neutral Wire is required. Confirm the wall box contains a Neutral Wire (typically white):
• The wire colors indicated in this manual are the usual colors and may differ in some homes.
• Ensure the wire conductors are securely fastened to each wire. Tum OFF the circuit breaker and test the power going to the switch Is off before wiring.
• This device is to be installed in a Wii box measuring at least 3″ x 2″ × 2-1/2″ (standard single gang electrical wall box) and wired in acco- dance with NEC article 314 box fill requirements.

STEP 1
Tum OFF the circuit breaker and test the power going to the outlet is off before wiring.

STEP 2
Remove the existing wall plate, tum on the power at the circuit breaker and use an electrical tester to check which wire is live wire; the tester will flash and/or chirp when it comes close to a Live Wire.

STEP 3
Tum off the power at the circuit breaker and use the electric taster to test if the power Is off, and then pull the existing switch out; label the Live Wire and other wires; disconnect the wires from the existing Outlet with pliers.

STEP 4
Follow the wiring diagram to connect the wires of the Outlet to the wires in the wall box using the wire conductors.

STEP 5
Mount the outlet with screws and snap the wall plate on it.

STEP 6
Tum on the power at the circuit breaker and outiet on.

ADD DEVICES

Download Smart Life APP

Please scan the QR code or download Smart Life on APP Store or Google Pley.

Registration or Log In

• Download the “Smart Life” Application
• Enter the Register/Login interface; tap ‘Register to* create an account by entering your phone number to get the verification code and “Set password”. Choose “Log in” if you already have a Smart Life account.

Configure the APP to the Outlet
Preparation: Ensure the switch has connected with electricity; ensure your phone has connected to WiFi router and is able to connect to the internet.

Note: this switch only supports 2.4G network. If you have connected 5G network, please disconnect 5G network firstly.

• Tap the icon “+” on the top right comer to add device; choose “Power Strip (Wi-Fi)”

Default Configuration Mode

• Press and hold the manual switch for 5 seconds until the orange indicator light blinks quickly (2 times per second
• Tap “Confirm indicator rapidly blink”; enter WiFI Password; wait for completing the connection.
• Devices have been added successfully.

AP Mode

• If you cannot configure successfully with the default mode, please try to connect with AP Mode.
• Tap “AP Mode”on the top right comer.
• Press and hold the manual outlet for 5 seconds, you can see the red indicator light blinks quickly. Then press and hold for 5s agal until the indicator light blinks slowly (once every 3 seconds).
• Tap “Confirm indicator slowly blink”
• Enter Wi-FI Password.
• Open WLAN settings and connect with “SmartLife-xxxx”.
• Back to the App and continue to add the device and wait for completing the connection®

Link “Smart Life” to Alexa / Google Assistant /

Go to Smart Life > »More for instructions to link Alexa/Google Assistant. Note: Please log in with your Smart Life account.

SPECIFICATION

TROUBLESHOOTING GUIDE

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These Ilmits are designed to provide reasonable protection agalnst harmful Interference in a residential instellation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular If installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the Interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the recelver is connected.
• Consult the dealer or an experienced radio / TV technician for help.

Please take attention that changes or modification-not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authonty to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant Is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

THANK YOU

If you have any questions, please feel free to contact us first. We are always here for you

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>