BESIGN BTH01 Wireless Headphones and Transmitter Set User Guide
- June 12, 2024
- BESIGN
Table of Contents
BESIGN BTH01 Wireless Headphones and Transmitter Set
Overview
Headphones
Transmitter:
LED Indicators
Turn on BTH01
Power up the transmitter /charging dock
Connect the transmitter/charging dock to a compatible power source using AC
adapter. Slide ON/OFF switch to “ON” position, POWER LED indicator lights up
BLUE.
Charge and turn on the headphone
Charge headphone for 2.5 hours prior to the initial use: Place the headphone
on transmitter/charging dock, the charging begins automatically, the CHARGE
LED on the transmitter/charging dock lights up RED. When the charging is
complete, the CHARGE LED on the transmitter/charging dock will turn off.
Turn on the headphone:
The headphones turn on automatically when you take it away from the
transmitter/charging dock or wear them on your ears. You could also press and
hold the multifunction button for 3 seconds to turn on the headphones
manually. Then the headphones will auto connect to the transmitter and the
transmitter LED indicator will turn SOLID blue. The auto-connection will take
around 1-2 minutes. If the headphones volume is too low, please insure both
Headphones & TV volume and make them both at the right level.
Adjust Volume on Headphone:
Short press “+”or “_” to raise or lower the volume. One will hear “beep” when
the volume reaches maximum.
Note: when using the transmitter connection, the headphones play, pause,
and previous / next track button operation functions are not workable.
Pair and connect the transmitter with the headphones again after auto-
connection failed.
Option 1:
A.Put the headphones back on the charging dock.
B.Switch off the transmitter with ON/OFF switch button, then switch it on
again.
C.Take the headphones away from the charging dock or wear on your head, then
the auto-connection will be completed in minutes. If it is not workable, you
could try it again as above solution later.
Option 2:
Clear the pair history / Restore factory default settings
Transmitter:
When the transmitter is powered on and the headphone has been taken out, press
and hold the “PAIR” button for 8 seconds, you will see the red LED on for 1
seconds, then the blue LED on 1 seconds. Make the transmitter power on again,
now the factory reset is completed.
Headphones:
When the headphones are powered on, press and hold both Volume + and Volume –
button for 5 seconds. Then switch off the headphones and power on again. After
the Factory defalt settings, you need to make both transmitter and headphones
into pairing mode for the re-connection.
Transmitter Pairing mode: blue and red LED light flashing alternately. When the transmitter is powered on and the headphone has been taken out, press and hold the “Blue LED Pair” button for 2 seconds.
Headphones Pairing mode: blue and red led light flashing alternately. When the headphones is powered on, it will enter into pairing mode automatically. When the headphones is powered off, press and hold the multifunction button for 3 seconds.
Auto-connection: keep the transmitter and headphones close to each other and wait. Once connected, the transmitter LED light will turn SOLID Blue.
Use BTH01 with your TV
Check your TVs output options before the set up BTH01 works with optical
output, AUX 3.5mm output, and RCA (labeled “Audio OUT”) output.
TVs with OPTICAL audio out
After turning on BTH01 and connecting cables, you should be able to hear sound from your headphones; if not
- Ensure your TV Speaker is set to “External Speaker”.
- Ensure TV Audio Format is set to “PCM” or “DOLBY/DTS” is off (This is IMPORTANT).
Note: Setting menu may be different depending on different TV brands and model.
To ensure the TV audio out signal is valid, you can contact TV manufacture support with your TV model number and ask
- how to set TV audio out to Optical;
- how to set Audio Out Format to PCM.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>