The Home Depot W117349883 12FT and 14FT Trampoline with Enclosure Instruction Manual

The Home Depot W117349883 12FT and 14FT Trampoline with Enclosure

Product Information

This product is a trampoline with an enclosure that comes in two sizes, 12FT and 14FT. It includes a jumping mat, spring cover pad, safety enclosure net, top rail, T-shaped connector, base leg, leg extension, top frame tube, board support tube, bottom frame tube, blue foam, spring, loading spring tool, ladder, net pole cap, long rope, black gap spacer, wind stake & band, lock nut, pole sleeves, and basketball hoop set. The product is designed to provide entertainment and exercise for people of all ages.

Product Usage Instructions

Before assembly, ensure that all parts required to assemble the product are present. If any part is missing, contact the seller for assistance. At least two people are required to assemble the trampoline.

Step 1 – Frame Assembly

1. Insert the top rail into the left and right ends of the T-shaped connector and ensure they are fixed well.
2. Repeat step 1 for the remaining top rails and ensure they are connected well with the T-shaped connectors.
3. Connect the bottom end of the leg extension to the base leg with the short screws.
4. Connect the upper end of the leg extension to the bottom end of the T-shaped connector with long screws while not tightening them yet.
5. Ensure the screw holes on all tubes are aligned and face outwards consistently. Put all long screws in the hole where the T-shaped connecting tube and the leg extension tube overlap. Maintain the main frame assembled stable enough to support 72/80 springs in step 3.

Step 2 – Jumping Mat Assembly

1. Place the jumping mat on the top rail frame assembled.
2. Select a starting point on the top rails frame and name it 1st Point.
3. To assemble the jumping mat, take out the loading spring tool included in the package.

Step 3 – Trampoline Spring Assembly

Please be careful where you place hands and other body parts during spring assembly, or the connection point may pinch you!

1. Place one end of the spring in the triangular ring of the jumping mat edge.
2. Attach the other end of the spring to the top rail frame with the loading spring tool.
3. Repeat step 1 and 2 until all springs are attached.

Step 4 – Spring Cover Pad Assembly

1. Place the spring cover pad on top of the trampoline springs and ensure it covers all springs evenly.
2. Attach the spring cover pad to the trampoline frame with elastic straps that are included in the package.

Step 5 – Enclosure Net Assembly

1. Slide the safety enclosure net over the top rail frame and secure it with pole sleeves and lock nuts.
2. Connect the bottom end of the T-shaped connector with long screws to the bottom frame tube while tightening the screws on the upper end of the leg extension (#7) with long screws (#16).
3. Attach the net pole cap to each pole of the safety enclosure net.
4. Fix the bottom of the safety enclosure net with the long ropes that are included in the package.

Step 6 – Ladder and Basketball Hoop Assembly

1. Assemble the ladder according to the instructions included in the package.
2. Assemble the basketball hoop according to the instructions included in the package.

After assembly, ensure that the trampoline is placed on a flatand stable surface. Regularly inspect and maintain the product to ensure safety during use.

Assembly Instructions

Before Assembly
Before assembly, please make sure you have all the parts required to assemble the product. If a part is missing, please contact the seller to get more help.

Note: At least two people are required to assemble the trampoline.

Step 1 – Frame Assembly

1. Insert the top rail (#4) into the left and right ends of the T-shaped connector (#5), (the thick end of one top rail matches the thin end of another top rail) and have them fixed well.
2. Repeat this operation for the remaining top rails (#4) and make sure top rails (#4) are connected well with the T-shaped connectors (#5).
3. Connect the bottom end of the leg extension to the base leg (#6) with the short screws (#17).
4. Connect the upper end of the leg extension (#7) to the bottom end of the T-shaped connector (#5) with long screws (#16) while do not tighten the screws for now, the screws (#16) here will be tightened with the bottom frame tube (#9) in step 5. As the picture shows below:
5. NOTE:
6. Please ensure the screw holes on all tubes are aligned and face outwards consistently.
7. Please make sure to put all long screws (#16) in the hole where the T-shaped connecting tube and the leg extension tube overlap. Maintain the main frame assembled stable enough to support 72/80 springs in step 3.

Step 2 – Jumping Mat Assembly

Place the jumping mat (#1) on the top rail frame assembled. Select a starting point on the top rails frame and name it “1 st Point”. To assemble the jumping mat, please take out the loading spring tool (#12) included in the package .

Step 3 – Trampoline Spring Assembly

Please be careful where you place hands and other body parts during spring assembly, or the connection point may pinch you!

1. STEP I: Place one end of the spring in the triangular ring of the jumping mat edge (1st Point).
   • STEP II: Use the loading spring tool (#12) to link up the other end of the spring to the other 1st point on the top rails frame. As the picture shows below:
2. To keep the tension on the mat balanced, install the second spring on the opposite side of the frame.

FOR 12FT TRAMPOLINE:

After having fixed two ends of the spring in the two “1st Point”, count to 37th point. (There are also two 37th points. One is on the top rail frame and the other one is on the triangular ring of the jumping mat edge.) and place the spring to connect the jumping mat with the top rail frame. The springs should be placed on opposite sides of the main frame alternatively, for example, 1st and then 37th; 18th and then 54th; 9th and then 45th; 27th and then 63rd. After finishing the installation of the springs above, now you should install springs on the 5th, 14th, 23rd, 32nd, 41st, 50th, 59th, and 68th.

FOR 14FT TRAMPOLINE:

After having fixed two ends of the spring in the two “1st Point”, count to 41st point. (There are also two 41st points. One is on the top rail frame and the other one is on the triangular ring of the jumping mat edge.) and place the spring to connect the jumping mat with the top rail frame. The springs should be placed on opposite sides of the main frame alternatively, for example, 1st and then 41st; 20th and then 60th; 10th and then 50th; 30th and then 70th. After finishing the installation of the springs above, now you should install springs on the 5th, 15th, 25th, 35th, 45th, 55th, 65th and 75th.

Tip: The number of triangular rings is equal to the number of points on the top rail frame. Please note that if you miscount a triangular ring of the jumping mat or point on the top rail frame, please remove the springs and reinstall them on the correct points.
BE CAREFUL: YOU MUST MAINTAIN A UNIFORM DISTRIBUTION OF THE SPRINGS TO AVOID UNEVEN TENSION DESTROYING THE TOP RAILS FRAME. Continue to place the remaining 56 / 64 springs in the same way as the above step

1. Note Again: All springs should be installed in a diagonal pattern to ensure the main frame is evenly stressed and the jumping mat is completely taut.
2. IMPORTANT: YOU MUST MAKE SURE THE SPRINGS ARE PLACED ON CORRECT POINTS AS THE INSTRUCTIONS.

Step 4 – Spring Cover Pad Assembly

1. Never use the trampoline without the springs cover pad (#2). The pad will reduce the risk of injury from impacting the metal structure. Make sure the frame and springs (#11) are completely covered by the spring cover pad (#2) before each use.
2. Place the spring cover pad (#2) on the frame assembled in step 3 and ensure it fully cover the springs (#11) and frame. Tie the elastic straps beneath the spring cover pad to the nearby spring (#11). Repeat this operation for the elastic straps beneath the spring cover pad. Note again: Make sure elastic straps beneath the spring cover pad (#2) are tightened and the spring cover pad (#2) completely covers the frame and all springs (#11) before using the trampoline. Don’t use the trampoline if the triangular ring connecting the jumping mat (#1) to the spring is damaged. Conduct a thorough inspection of the trampoline to ensure that all parts are assembled correctly. Read this manual and make sure you fully understand all warnings in the various warning signs.

Step 5 – Trampoline Poles Assembly

Align the 2 bottom holes of the bottom frame tube (#9) with the 2 upper holes of the leg extension (#7) and have them fixed with the long screw (#16), black gap spacer (#19), washer (#18) and locknut (#21). As shown in the below picture: Repeat this step for the remaining bottom frame tubes (#9).
Note: Please check all screws carefully and make sure all of them are tightened well to ensure safety

Step 6 – Trampoline Basketball Hoop Assembly
Please note that there is an #8B and #9B specially used for the basketball hoop. #8B has 1 hole in the end. #9B has 1 hole on the top, 2 holes on the end. Please make sure you use the right poles of the basketball hoop. First, fix the basketball hoop ring(#23) in the basketball hoop board(#24) with board fix pin A(#26), board fix pin B(#27), and 4 short screws(#32). Second, fix the basketball hoop board(#24) on the top of the board support tube(#8B) with board fix pin B(#27), board fix pin C(#28), and 4 long screws(#33).

Step 7 – Trampoline Upper Poles Assembly

Insert top frame tube (#8A) into bottom frame tube (#9A). Repeat this operation for the remaining top frame tubes. Insert the board support tube (#8B) into the bottom frame tube (#9B) and fix itself by the springs snap within the board support tube (#8B). Please make sure the basketball board faces toward the trampoline. For the 12FT&14FT trampoline, after finishing the installation of the poles, cover the pole sleeves (#22) which can protect the trampoline poles. Then place net pole caps (#14) on the remaining top frame tubes (#8A). Please keep all blue foams (#10) cover the frame tubes before connecting the bottom frame tubes with the top frame tubes.

Step 8 – Trampoline Enclosure Net Assembly

1. Insert the strap on the safety enclosure net (#3) through its buckle and lock the buckle, adjust the tightness of the strap as needed, and place it on the net pole cap (#14). Repeat this operation for the remaining straps on the safety enclosure net (#3). PS: For the strap putting on the board support tube (#26), please make the strap and its buckle go around below the board support tube and loop it by locking the buckle.
2. Pull one end of the long rope (#15) through the lower hole of the safety enclosure net (#3) and the triangular ring on the jumping mat (#1) successively, until it meets its other end, and tie the two ends of the long rope (#15) together beneath the spring cover pad (#2) to fix the bottom of the safety enclosure net (#3). Please note there are several holes on the lower edge of the safety enclosure net (#3) designed to let the long rope (#15) pass to fix the bottom of the safety enclosure net (#3).

Congratulations! You’re ready to jump!

The trampoline load capacity is up to 1500LBS after the factory’
NOTE: WHEN A PERSON USES THE TRAMPOLINE ALONE, THE RECOMMENDED MAXIMUM WEIGHT IS 330 LBS/150 KG TO AVOID INJURIES CAUSED BY A SINGLE-POINT FORCE.
WARNING: Ladder helps children climb onto the trampoline. This trampoline is not recommended for children under 6 years old. Please remove the ladder when you don’t use the trampoline.
DANGER:

1. Do not attempt or allow somersaults on the trampoline. It may 　cause serious injury, paresis, or death when landing on the head or 　neck, even when landing in the middle of the bed.
2. Trampolines should not be used for more than 3 adults 　 weighing more than 330lbs at a time, there is an increased 　 likelihood of injury.
3. Children 0-6 years old need to use the trampoline under 　 supervision.
4. Do not use the trampoline in strong wind conditions as wind will cause unexpected movement of the trampoline. The product must be properly stored or disassembled completely in severe windy conditions.

SAFETY INSTRUCTIONS FOR TRAMPOLINE ENCLOSURE NET

A NOTICE TO THE SUPERVISOR

1. The supervisor is strictly to enforce the safety rules and be familiar with all the information provided on the trampoline.

2. No trampoline user shall use the trampoline without mature adult supervision, regardless of the skill or age of the trampoline user. Secure the trampoline against any unauthorized use. Keep objects away from the jumper and the trampoline that may interfere with the jumper or could be potentially hazardous.

3. The trampoline enclosure system is not recommended for use by children under the age of 6 or anyone weighing more than 330 LBS (150kg).

4. Use only when the trampoline jumping mat is clean and dry. Inspect the trampoline and enclosure before using and replacing any parts. Use only when the enclosure has no holes, pole clamps are tightly secured to the poles and the frame and the barrier is properly suspended.

5. Children must never be left unattended in the enclosure at any time.
   B. NOTICE TO JUMPER

6. Do not use the trampoline and the enclosure net when one is under the influence of drugs or alcohol. Do not smoke while using the trampoline and the enclosure.

7. Avoid jumping too high or too long on the trampoline. Always control your jumping. Do not try to jump over the barrier.

8. Always have someone watch you when using the trampoline. Do not jump alone.

   • WARNING: MAKE SURE ALL INSTRUCTIONS ABOVE FOLLOWED

9. Do not climb on trampoline frames that are not equipped with a spring cover pad.

10. Do not wear clothing drawstrings, hooks, loops, or anything that could get caught while using the trampoline/net, or it may result in entanglement or strangulation.

11. Only climb on and off the trampoline at the net door opening. Do not crawl under the trampoline frame. Do not use the trampoline as a springboard to other objects.

12. Do not jump from other objects, buildings or surfaces onto the trampoline or into the trampoline net

WARNING

Do not jump into the enclosure netting deliberately. Do not jump and try to hang onto the top of the netting or the enclosure pole. Misuse of the enclosure as stated above may result in serious injury or death. Users may become entangled in or strangled by loose cords or in gaps between trampoline and enclosure keep enclosure tightly fastened to the trampoline in accordance with the manufacturer’s instructions. Failure to properly assemble and maintain a tight, secure trampoline/enclosure boundary may result in serious injury, strangulation or death.

WARNING

Your trampoline enclosure netting is manufactured with UV-resistant material. The netting is exposed to outdoor elements including sunlight, wind, rain and wildfire for a long time, so the enclosure netting must be checked before each use for wear or tear by pinching a section of fabric between fingers and pulling, stretching. Please see the diagram below.

If it produces a tear or if it produces a continuous ripping sound, then the net is unsafe and must be taken down immediately. STOP USING THE TRAMPOLINE IF YOU FIND ANY SIGNS OF WEAKNESS. RESTRICT ACCESS BY USERS UNTIL A NEW AUTHORIZED REPLACEMENT NETTING IS INSTALLED OR STORE THE TRAMPOLINE.

100% Customer Satisfaction Guaranteed
Tel: +17607909599 (Mon-Fri 18:00 PM-3:00 AM, PDT Time)
Email: WeAreHere-Service@outlook.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>