Producer s PRIDE 2015286 PP Chateau Chicken Coop Instruction Manual
- June 12, 2024
- Producer s PRIDE
Table of Contents
Producer s PRIDE 2015286 PP Chateau Chicken Coop Instruction Manual
Tools required for assembly (not included)
Distributed by: TRACTOR SUPPLY COMPANY
5401 VIRGINIA WAY, BRENTWOOD, TN 37027
For customer support, call:
1-888-376-9601
www.TractorSupply.com
MADE IN CHINA
PARTS LIST
ASSEMBLY
Step 1
Attach Coop Bottom Mesh-Back (#8) and 2pcs Coop Bottom Mesh-Side (#9),between the 4 Posts (#1, #2, #3, & #4) by M6x30 Bolt (#48) and M6 Nut (#50).
Note: Please pay attention to the post direction, and also make sure all the panels are in same level.
Step 2
Assemble the Coop Back Frame-Bottom (#10) with 4pcs Self-tapping Screw 4×30 (#54).
Note: Make sure #10 sits on #8 without any gap in between.
Step 3
-
Take 2pcs Coop Back Panel – Top (#11) and 4pcs of Roof Support Connector 3 (#47). Fix 1pc of Roof Support Connector 3 (#47) on each side of the Peak position of Coop Back Panel – Top (#11) by Self-tapping Screw 3.5×20 (#55).
Noted: Make sure the bottom of #47 is aligned with the square wood frame of11.
-
Assemble 1pc #11 board on top of #10 frame with 4pcs Self-tapping Screw 4×30 (#54).
Step 4
Assemble Coop Right Panel (#12) between Posts #1 and #3 by 6pcs Self-tapping Screw 4×30 (#54).
Step 5
Same as Step 4, assemble Coop Left Panel (#13) between Posts #2 and #4 by 6pcs Self-tapping Screw 4×30 (#54). 13 54
Step 6
Put Coop Bottom Floor (#14) on top of the two bottom bars of Panels #12 and
13. Then put the PVC Board (#15) on top of #14.
Step 7
Assemble Coop Front Panel – Bottom (#16) by 4pcs Self-tapping Screw 4×30 (#54) from inside of the coop.
Step 8
Fix the 2nd Coop Back Panel – Top (#11) board on top of board #16.
Step 9
Put the 4pcs Roosting Bar (#42) between the 8 blocks as below.
Step 10
Assemble Nesting Box Right Panel (#17) and Nesting Box Left Panel (#18) to the two sides of Coop Back Frame (#10) with Self-tapping Screw 4×50 (#52).
Step 11
Slide the Nesting Box Floor (#20) into the two U-channels on the bottom of Nesting Box Right Panel (#17) and Nesting Box Left Panel (#18). Push the floor all the way inside.
Step 12
Assemble the Nesting Box Back Panel (#19) with 4pcs Self-tapping screw 4×50 (#52).
Step 13
Insert the 3pcs Nesting Box Divider (#21) into the Nesting Box Floor (#20).
Step 14
Attach the Nesting Box Roof (#22) by Self-tapping screw 4×40 (#53).
Step 15
Fix the 2pcs Pen Mesh Panel (#23) on Posts #3 and #4 , each panel with 4pcs M6x30 Bolt (#48) and 4pcs M6 Nut (#50).
Step 16
Fix the Sliding Door Helper (#46) with M4x20 Bolt (#49) and the Ramp (#41) with M6x30 Bolt (#48) and M6 Nut (#50).
Step 17
Following below diagram, fix 2pcs Post 5 (#5) , 2pcs Pen Mesh Panel (#23) and Post 6 (#6), Post 7 (#7) in turn. Requires totally 24pcs M6x30 Bolt (#48) and 24pcs M6 Nut (#50)
Step 18
Now fix the Pen Front Right Panel (#24) on Post 6 (#6), and the Pen Front Left Panel (#25) on Post 7 (#7), each by 4pcs M6x30 Bolt (#48) and 4pcs M6 Nut (#50).
Step 19
Assemble the Pen Door Panel (#26) between above two side panels, by 4pcs M6x30 Bolt (#48) and 4pcs M6 Nut (#50) on each side. The flange for the door frame needs to be at the top.
Step 20
Put the Pen Top Triangle Panel (#27) on top of the Door Panel (#26), fix by M6x30 Bolt (#48) and M6 Nut (#50).
Step 21
From the top end of Post 7 (#7) and Post 5 (#5) assemble the Left Shoulder Brace 1 (#29) by Self-tapping Screw 4×60 (#51). Then continue to assemble Left Shoulder Brace 2 (#31) on top of Post 2 (#2) and Post 4 (#4) by Self-tapping Screw 4×60 (#51). Make sure the two braces (#29 & #31) in same line, and no gap. Then use the Shoulder Brace Connector (#45) connect the two braces together by Self-tapping Screw 4×30 (#54).
Step 22
Same as Step 21, assemble the Right Shoulder 1 (#28), the Right Shoulder Brace 2 (#30) on top of the other 4 posts (#1, #3, #5, #6). And connect the 2 braces together with Shoulder Brace Connector (#45).
Step 23
Take 2pcs Roof Support 1 (#32), 1pc Roof Support Connector 1 (#43), 1pc Roof Support Connector 2 (#44),follow below diagram (1) assemble them together by Self-tapping Screw 3.5×20 (#55).
Take 2pcs Roof Support 2 (#33), 2pcs Roof Support Connector 2 (#44), follow below diagram (2) assemble them together by Self-tapping Screw 3.5×20 (#55).
Take 2pcs Roof Support 3 (#34), 1pc Roof Support Connector 1 (#43), 1pc Roof Support Connector 2 (#44),follow below right diagram (3) assemble them together by Self-tapping Screw 3.5×20 (#55).
Step 24
Assemble above 3 sets of roof support combination by Self-tapping Screw 4×60 (#51).
Step 25
Put Roof Ridge 1 (#35), Roof Ridge 2 (#36), Roof Ridge 3 (#37), Roof Ridge 4 (#38) in below diagram position. Fix them on to Roof Support Connector 1 (#43), Roof Support Connector 2 (#44), and Roof Support Connector 3 (#47),by Self-tapping Screw 3.5×20 (#55).
Step 26
Put the 6pcs Roof Panel (#39) evenly spaced on two sides of the roof, and fix them on the Roof Supports by Self-tapping Screw 4×19 (#56). 39 39 39
Step 27
Put the 3pcs Roof Ridge Metal Cover (#40) on the peak of the roof, fix by Self-tapping Screw 4×19 (#56).
Step 28
Assemble 1pc Lock (#57) on the Coop Left Panel (#10) as below diagram, using Self-tapping Screw 3.5×20 (#55).
Step 29
Assemble 1pc Door Latch (#58) on the Pen Door Panel (#26), using M6x30 Bolt (#48) and M6 Nut (#50).
Step 30
Follow below door lock assembly instruction assemble T-Handle Lock (#59, with longer tongue) on Coop Door (#10), and T-Handle Lock (#60, with short tongue) on Nesting Box Back Panel (#19).
T-Handle Lock Assembly:
- Insert T-handle shaft into the pre-drilled hole on the wood panel, leaving 1/4″space outside. Then from the back of the panel, tighten the M10 nut (not the Locknut) first, then put the tongue in, make sure the tongue is in the same direction of the T-handle, fix the washer and M10 Locknut and tighten them.
- When using the lock, please remember that you need to push in the 1/4″ gap first before you turn the T-handle. Clockwise is close, counter clockwise is open.
Now the assembly is finished.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>