CANNABIS HARDWARE Tegridy 20 Ton Rosin Press User Manual
- October 30, 2023
- CANNABIS HARDWARE
Table of Contents
HARDWARE Tegridy 20 Ton Rosin Press
User Manual
Rosin Press
Tegridy and BVA lines of Rosin Presses
Introduction
First, I would personally like to extend my thanks for choosing Cannabis
Hardware as your source for all things Rosin Press. We are very proud of how
far we have come in evolving our products and are extremely excited to share
it with you. The design of the Rosin Press is the culmination of 25 years of
engineering and machining experience which started in the Orthopedic and
Dental fields. Nowadays, I am extremely grateful to merge my two passions in
life, machining and cannabis, and now I get to share my contribution with our
ever-growing industry.
I hope your new Rosin Press brings you a lifetime of production and fun!
Edwin Pyron
Owner and
About your Packaging
When you purchase a Rosin Press from New Vape, you will receive two boxes with
all the contents. These contain everything you need to get started.
– (1) Assembled Tegridy 20 Rosin Press body
– (4) Gravity drip enabling feet
– (1) Custom Engraved Wooden Handle
– (2) Brackets for the Wooden Handle
– (1) PID Controller with 4 heaters and two thermocouplers
– (1) Upgraded Pump Handle
– (1) Tool Bag (4 (+1) Allen screws for handle and 8 (+1) for feet and 2 Allen
wrenches)
Assembling the “Gravity Drip” Feet
These are the parts you will need (included):
– 4 Gravity Drip Feet
– 8 Short Allen Screws
– 1 Allen Wrench
Install each foot by finger tightening the Allen screws first, then use the
Allen wrench to tighten them. This is what your press should look like with
the “Gravity Drip Feet” installed.
Assembling the Custom Engraved Wooden Handle
You will need these parts (included):
– 4 Long Allen Screws
– 2 Handle Brackets
– 1 Allen Wrench
Align the holes in the bracket with the holes on the top of the press and run the onfallen screws until it catches the bracket.
Use Allen Wrench to tighten in place, then hold the second bracket in place
with the handle installed. 
Use remaining long Allen Screws to tighten
the second bracket in place.
Assembling the Custom Pump Handle
Align hole in handle with the pump insert hole
Tighten the Pump Handle in place.
This is what it should look like.
Assembling the PID Controller to the Press
It does not matter which set of heaters you decide to assign to the top and
bottom plates. However, it is a good idea to label them so as to remain
consistent. Once you have decided which set of heaters to assign to each
place, go ahead and insert them. Each set of heaters goes into one
plate.
There is a thermocouple that tags along with each set of heaters. These help
in giving an accurate temperature reading back to the controller. The need to
be threaded into the middle hole on each plate. 
On each side of each
plate there are recessed screws which will tighten onto the heating rod from
the inside and keep them in place. Check that you have done it correctly by
lightly pulling on the heater rods. If they do not come out of the plate, you
are set.
This is what it should look like with the heating rods and thermocouple
installed correctly.
How to adjust temperature on PID controller
Here are some temperature recommendations to get you started
Times, Temps, and Mesh Sizes
| Material | Mesh Size | Temp | Time |
|---|---|---|---|
| Flower | 90.120 | 190E-220F | 15-60 Seconds |
| Sift & Bubble | 25-37 | 150E-190F | 20-60 Seconds |
The 2×3″ bags can hold 1/4 oz. of flower
The 3×6″ bags hold 1 oz of flower
The prepress make filling the bags to max capacity much easier.
Presses Rosin Presses
Tegridy and BVA Rosin
- Aluminum and Stainless Construction with gravity drip detachable legs
- Adjustable opening
- Bronze, self-lubricating bushings
- Easy pump replacement
- Plates heat evenly
- Rated at 20 tons.
Packing Dimensions and Weight
Number of Boxes: 2
Box Dimensions: (1) 18″x18″x8″ and (2) 12″x12″x6″
Combined Weight: 72 lbs.
Specifications
PID TEMP CONTROLLERS BOX – TCO4R115
Model No.: dp-tc04r115
Voltage: 110V & 1,000
Watts – American Standard
Temp Range: 0-400°F
INSTRUCTIONS:
1# Turn on Main Switch, Start Reading Temp of Plates;
2# Turn on Two Sub-switches, Plates Start Heating up;
3# Turn off Two Sub-switches, Plates Stop Heating, But Still Read Temp;
4# Turn off Main Switch When Plates’ Temp Under 90F.
MADE IN CHINA
Documents / Resources
|
CANNABIS HARDWARE Tegridy 20 Ton Rosin
Press
[pdf] User Manual
Tegridy 20, DP-TC04R115, TC04R115, Tegridy 20 Ton Rosin Press, Tegridy, 20 Ton
Rosin Press, Rosin Press, Press
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>