BICYCLE GLASS 767 Semi Flush Light Instruction Manual

BICYCLE GLASS 767 Semi Flush Light

Product Information

The Bicycle Glass Co. Semi-Flush Assembly and Wiring Instructions are designed to guide users on how to install and wire the hardware. The instructions are subject to revision, and the hardware is meant to install into a standard ceiling electrical box/junction box. The hardware comes with a parts list that includes a canopy plate, mounting strap, canopy screws, mounting screws, wire connectors, socket set, shade ring, and glass shade. The wire designation chart identifies the physical description and electrical designation of the wires for brushed nickel, polished brass, and antique bronze hardware.

Product Usage Instructions:

Before installing the hardware, it is recommended to consult a certified electrician. Follow these instructions:

1. Turn OFF the power at the breaker box.
2. Remove the existing light fixture from the ceiling electrical box.
3. Remove the mounting strap from the canopy plate by removing the two canopy screws from the sides of the canopy plate. Save mounting strap and canopy screws for later use.
4. Attach the mounting strap to the ceiling box with tabs facing downward using the two mounting screws provided. Make sure the canopy plate can be mounted snugly to the ceiling after the mounting strap is attached to the ceiling electrical box when wiring is complete.
5. Connect the black wire of the fixture to the black wire of the ceiling electrical box using an orange wire connector provided. See WARNING #2 and WARNING #3.
6. Connect the white wire of the fixture to the white wire of the ceiling electrical box using an orange wire connector provided. See WARNING #2.
7. Connect the bare ground wire from the mounting strap to the green/bare wire of the ceiling electrical box and the green wire from the fixture using an orange wire connector provided. See WARNING #1 and WARNING #3.
8. Carefully arrange any excess wiring and orange wire connectors within the canopy plate and the ceiling electrical box.
9.  Align holes in the side of the canopy plate to the holes at the ends of the mounting strap while pushing it snugly to the ceiling. Insert the two canopy screws and tighten them.
10. Remove the shade ring from the E26 socket set on the fixture.

PLEASE CONSULT A CERTIFIED ELECTRICIAN BEFORE INSTALLING THE HARDWARE. DRAW- INGS ARE NOT TO SCALE AND ARE FOR REFERENCE ONLY. THESE INSTRUCTIONS ARE SUBJECT TO REVISION. THIS HARDWARE IS MEANT TO INSTALL INTO A STANDARD CEILING ELECTRICAL BOX/ JUNCTION BOX.

PARTS LIST

The illustrated figure is Model 767: 7-inch inside diameter, 5 1/8 inch opening, 6 3/4 inch high. Your selected shade may be different.

WIRE DESIGNATION CHART

BRUSHED NICKEL HARDWARE:

BLACK/ POLISHED BRASS/ ANTIQUE BRONZE HARDWARE:

Instructions

1. Turn OFF Power at Breaker Box.
2. Remove the Existing Light Fixture from the Ceiling Electrical Box.
3. Remove the Mounting Strap (E) from Canopy Plate (A) by removing the two Canopy Screws (B) from the sides of the Canopy Plate (A). (Save Mounting Strap (E) and Canopy Screws (B) for later use.)
4. Attach the Mounting Strap (E) to the ceiling box with the tabs facing downward, using the two 8-32 Mounting Screws (F) provided. Make sure that Canopy Plate (A) can be mounted snug to the ceiling after the Mounting Strap (E) is attached to the Ceiling Electrical Box when wiring is complete.
   PRO TIP : Take a photo of the existing wiring on your phone to use as a reference before removing it.

5. Connect the BLACK Wire of the fixture to the BLACK Wire of the Ceiling Electrical Box using an Orange Wire Connector (I) provided. (See: WARNING #2 and WARNING #3)
6. Connect the WHITE Wire of the fixture to the WHITE Wire of the Ceiling Electrical Box using an Orange Wire Connector (I) provided. (See: WARNING #2)
7. Connect the BARE Ground Wire from Mounting Strap (E) to the GREEN/BARE Wire of the Ceiling Electrical Box and the GREEN Wire from the fixture, using an Orange Wire Connector (I) provided. (See: WARNING #1 and WARNING #3)
8. Carefully arrange any excess wiring and Orange Wire Connectors (I) within Canopy Plate (A) and the Ceiling Electrical Box.
9. Align holes in the side of the Canopy Plate (A) to the holes at the ends of the Mounting Strap (E), while pushing it snug to the ceiling, insert the two Canopy Screws (B) and tighten.
10. Remove the Shade Ring (V) from the E26 Socket Set (U) on the fixture.
11. Attach the Glass Shade (W) to the E26 Socket Set (U) through the hole at the top of the Glass Shade (W). Use the Shade Ring (V) to tighten the Glass Shade (W) to the hardware. (See: NOTICE #1 and WARNING #4)
12. Install one medium E26 base light bulb into the E26 Socket Set (U). (See: WARNING #5)
13. Turn ON Power at Breaker Box to test the fixture.

WARNINGS:

• WARNING # 1: Never connect Ground Wire (GREEN or BARE) to WHITE/Neutral or BLACK/Hot Wire.

• WARNING # 2: Never connect the BLACK/Hot Wire to the WHITE/Neutral Wire.

• WARNING # 3: Orange Wire Connectors (I) provided are designed to connect TWO to FOUR 18-gage wires and may be appropriate for your wiring situation. All wiring should be snugly and securely fastened with correctly sized wire connectors. If your wiring differs from this most simple example, you should con-sult a qualified electrician to be sure that the wiring is done safely and correctly with appropriately sized connectors for your unique wiring situation.

• WARNING #4: Do NOT over-tighten the Shade Ring (V) as the Glass Shade (W) may crack or break.

• WARNING # 5: The hardware has a 60-watt INCANDESCENT MAX rating. Do NOT exceed this rating.
  For California residents, it is recommended to not go beyond a 10-watt LED MAX rating.

• NOTICE # 1: Brushed Nickel fixtures come with clear cord. The clear cord comes with distinct heat-shrink-colored labels instead of fully colored wires. Other finishes come with either black or brown cord and the individual wires are BLACK/Hot, WHITE/Neutral and GREEN/Ground.
  (SEE: ‘WIRE DESIGNATION’ CHART AT THE BEGINNING OF INSTRUCTIONS).

• NOTICE #2: Make sure the power is OFF before attempting to adjust the Glass Shade (W). The flange of the Shade Ring (V) (wide and flat side of the ring) screws around the E26 Socket Set (U) against the Glass Shade (W) to affix it to the lighting fixture. The hole at the top of the shade is slightly larger than the E26 Socket Set (U). If the shade hangs slightly crooked then hold Glass Shade (W) while unscrewing the Shade Ring (V) a few turns. Once the Glass Shade (W) is loose, recenter the Glass Shade (W) to hang straight and then re-tighten the Shade Ring (V) to set Glass Shade (W) in place.

© Bicycle Glass Co. v8 January 2022

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>