Afoxsos HDMX1620S Aluminum Folding Electric Bike Ebike Bicycle Instruction Manual

Afoxsos HDMX1620S Aluminum Folding Electric Bike Ebike Bicycle

Product Description

Safety Notice

To Ensure Your Safety, Make the Following Functional Checks Before Driving:

1. Test brake system, throttle, and power system.
2. Tire pressure should be at 30 psi.
3. Check front wheel lug nuts, securely tighten before every ride.
4. Battery charge level- found on side of battery.
5. Braking system adjustment and free operation.

Installation Instructions

1. Open your package.

2. Take out the toolbox.

3. Take out the bicycle from the package and put it on a soft surface to avoid scratches. Cut the tie that secures the front wheel to the side

4. Remove the protective foam.

5. Open the accessory kit and remove the tool kit

6. Invert the bicycle.

7. Remove the large fixing bolt on the front fork.

8. Put the front wheel on the front fork and place the disc brake pad on the front wheel in the middle of the disc brake caliper Figure 1).

9. Use the supplied 15mm flat tool to tighten the two bolts.

10. Tie the key to the handlebar clamp, cut the zipper, and then use the Allen wrench in the tool kit to remove the clamp.

11. Place the handlebar in the middle position (Figure 2), install the rod clamp and tighten the screws with the included Allen wrench.

12. Install the LCD display on the handlebar (Figure 3), tighten the screws, and connect the green connecting wire (Figure 4)

13. Grasp the bicycle light and unscrew the lens. Then, remove the plastic insulator, re-tighten the lens, and then connect the red cable (Figure 5), and connect the bicycle light to the screw above the front fork (Figure 6).

14. Install the pedal. The right pedal rotates clockwise (Figure 7), and the left pedal rotates counterclockwise (Figure 8).
    NOTE: Pedal mark “L” means left and “R” means right.

15. Vertical bicycle

16. Push the seat into the column, fix it in the desired position, tighten the screws, and then fix it.

17. Installation is complete. When connecting meters, headlights, brake circuit breakers, handlebars, etc., please align them and do not install them violently(Figure 4).

Folding Steps

1. Fold the pedal, hold both sides of the pedal with both hands, shrink and fold inward
2. Fold the front and lift up the front handle
3. Push the lock switch outwards, hold the handle and fold inward immediately
4. Fold the body, push the lock switch upwards, and then turn the switch clockwise
5. Hold both sides of the body and fold inward
6. Fold the seat cushion, lift the switch under the seat cushion and grab the seat cushion, lift up to fold the seat cushion, turn the battery key counterclockwise to unlock the battery, and take out the battery
7. After folding, you can easily put A20 in your car trunk or put it at home, which will save your space even more

Display Use & Maintenance

866 display
Introduction to key functions

• OPEN: 1.5 seconds long press.
• CLOSE: In standby mode, long press for 3 seconds.
• SETTING: After booting, press ****for 2.5 seconds.

The detailed settings are as follows:(on the boot state) (The following content, up means , down means .

• Ride your bike in a safe way. Don’t hit or knock the display.
• Keep away from the bad environments when use, such as downpours, large snowflakes and solarization.
• Try not to use in under-voltage condition.
• The screen will gets dark along with the temperature reduction when temperature below -10°C. The screen will return to normal when the temperature rises again.

Controller Use & Maintenance

1. Battery negative connection line

2. Battery-positive connection line

3. Phase line

4. Tail light wire

5. Integrated main line

6. Power sensor line

7. Motor Hall plug wire

8. Please be careful not to get water into the controller box

9. When the bike does not work: 1)Check the connection of controller cables;

10. Try to restart or Replace the controller; 3)Contact us with email

Motor Maintenance

1. Please check the integrity of motor blocking piece regularly.
2. Please check the integrity of cable before and after riding.
3. Please check the integrity of motor shell before and after riding.
4. Please do not use the motor in extreme environments, and do not let the motor work in water.
5. When you find the motor power is insufficient, please get out of the bike and not force it.

FAQ

• Is there a power usage or battery gauge on the bike?
  Yes, there is a full-screen LCD display. There is also an additional LED battery gauge on the side of the battery pack. 2x the info!

• Is there a switch to prevent accidental starting?
  Yes, there is an on/off button on the battery pack. The brake levers also come standard with a safety power stop switch built in.

• How do I lock it up and what can I do to help minimize the chance of it being stolen?
  AOSTIRMOTOR Bike has some great anti-theft features, including a locking battery rack with keys to keep bike safe, and rear wheel which is bolted down reduce the chances to be stolen. Most standard U-locks and cable locks work fine on our AOSTIRMOTOR Ebike.

• Does it work in the rain?
  The components are all waterproof and work very well in wet conditions, But we do not suggest to use our ebike in a rain day. We suggest that you should keep your bike parked indoors and keep him in a dry situa- tion.

POWER BRINGS JOY
www.aostirmotor.com
aostirmotor@gmail.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>