BOSCH SMS6EMI65Q Dishwasher User Guide
- October 30, 2023
- Bosch
Table of Contents
- BOSCH SMS6EMI65Q Dishwasher
- Product Information: Dishwasher
- Product Usage Instructions
- Setting up Home Connect
- Overview of water hardness settings
- Setting the water softening system
- Instructions
- Programmes
- How to use your appliance
- Cleaning filters
- Cleaning spray arms
- Clean wastewater pump
- Troubleshooting
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
BOSCH SMS6EMI65Q Dishwasher
Product Information: Dishwasher
The dishwasher comes with a quick reference guide and an instruction manual
that contains safety information. Before using the dishwasher for the first
time, it is essential to read the instruction manual. The dishwasher can be
set up using the Home Connect app, which can be installed on a mobile device.
The app allows users to change all settings conveniently. The dishwasher has
an overview of water hardness settings. Users
can select the water hardness values from the table provided in the
instruction manual. The dishwasher has a dispenser for special salt and rinse
aid. Users should only add special salt to the dispenser just before the
program starts to avoid damage to the appliance. The dishwasher has different
programs with varying durations, energy consumption, and water usage. The
program data has been measured in the laboratory according to European
standard EN 60436. The running time will change if the rinse aid system is
switched off or if rinse aid needs to be added. The dishwasher has a suitable
program for running at night, which takes longer but is extremely quiet.
Product Usage Instructions
- Load the tableware into the dishwasher. Only clean tableware that is suitable for dishwashers. Remove large remnants of food from the tableware.
- Add detergent to the dry detergent dispenser according to the recommended amount for each program. Close the lid of the detergent dispenser.
- Switch on the appliance.
- Select the desired program from the available options.
- Start the program.
- At the end of the program, remove the tableware from the dishwasher.
- To cancel a program, press and hold down the cancel button for approximately four seconds. The program will be canceled and end after approximately one minute.
- After each wash, check the filters for any debris and clean if necessary.
Note: To set up the dishwasher, users should install the Home Connect app
on a mobile device and follow the instructions provided in the instruction
manual.
Users can scan the QR code with the Home Connect app to connect the appliance
to the mobile device. The water hardness system can be set up by following the
instructions provided in the instruction manual. To add special salt, unscrew
the lid of the dispenser for special salt and add the salt just before
starting the program. To add rinse aid, press the catch on the lid of the
dispenser for rinse aid and lift. Add rinse aid up to the max mark and close
the lid of the dispenser.
Before using for the first time, read the instruction manual and the safety information it contains
Setting up Home Connect
Tip: Connect your appliance to a mobile device. You can conveniently change all settings using the Home Connect app
- Install the Home Connect app on your mobile device and follow the instructions.
- Scan the QR code with the Home Connect app
Overview of water hardness settings
You can find an overview of the water hardness values that can be selected here. A table of country-specific units can be found in the instruction manual.
Setting the water softening system
- Press .
- To open the basic settings, press for 3 seconds.
- The display shows H:xx.
- The display shows .
- Press or repeatedly until the right water hardness has been set.
- To save the settings, press for 3 seconds.
Instructions
Programmes
- The programme data has been measured in the laboratory according to European standard EN 60436.
- The consumption figures depend on the programme and additional function selected.
- The running time will change if the rinse aid system is switched off or rinse aid needs to be added.
How to use your appliance
-
Load the tableware.
Only clean tableware that is suitable for dishwashers. Remove large remnants of food from the tableware. Check that the spray arms can rotate freely. -
Add detergent.
-
Switch on the appliance .
-
Select the programme.
-
Start the programme.
-
Remove the tableware at the end of the programme.
-
To cancel the programme, press for approx. 4 seconds.
The program is canceled and ends after approx. 1 minute.
Cleaning filters
- After each wash check the filters for residue.
- Turn the coarse filter anticlockwise 1 and remove the filter system 2.
- Pull down the microfilter to remove it.
- Press the locking catches 1 together and lift the coarse filter out 2.
- Clean the filter elements under running water.
- Re-assemble the filter system.
- Insert the filter system into the appliance and turn the coarse filter clockwise. Make sure that the arrow markings match up.
Cleaning spray arms
- Unscrew the upper spray arm 1 and pull down to remove 2.
- Pull up the lower spray arm to remove it.
- Check the outlet nozzles on the spray arms for blockages under running water and remove any foreign bodies.
- Insert the lower spray arm.
- The spray arm clicks into position.
- Insert the upper spray arm and screw it firmly in place.
Clean wastewater pump
- Disconnect the appliance from the power supply.
- Remove the filter system.
- Scoop out any water.
- Prise off the pump cover using a spoon and grip it by the crosspiece.
- Lift the pump cover inwards at an angle and remove.
- Remove any remnants of food and foreign bodies in the area of the impeller.
- Insert the pump cover 1 and press down 2.
- The pump cover clicks into position.
- Install the filter system.
Troubleshooting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>