PITTSBURGH 67441 Heavy Duty Load Leveler Owner’s Manual
- October 30, 2023
- PITTSBURGH
Table of Contents
PITTSBURGH 67441 Heavy Duty Load Leveler
Product Information
The product is a Leveler designed for use with shop cranes or hoists suitable for load, with a rated capacity of 1500 lb and a length of 16 inches. It is designed to assist in balancing loads while lifting them with a crane or hoist.
Usage Instructions
- Before using the Leveler, make sure that the product is intact and undamaged. If any parts are missing or broken, contact 1-888-866-5797 as soon as possible.
- Ensure that the load to be lifted is secured to the device and does not exceed the rated capacity.
- Attach the Hanger to a Crane or Hoist (sold separately).
- Secure the load to the Brackets.
- Turn the Handle to move the load to its balance point, so that it is hanging evenly from the Leveler.
- Lower the load and detach Leveler after use. Do not use to support load for extended periods.
- Gently grease the Threaded Bar (7) as needed to ensure that the Sliding Block (6) moves smoothly.
- Inspect the Leveler before every use and do not use if parts are loose or damaged.
- Wear ANSI-approved safety goggles and heavy-duty work gloves during setup and use.
- Do not use for lifting human weight or overhead lifting. Keep clear of raised load.
- Do not work underneath, on, or near a lifted load.
- Keep bystanders out of the area during use.
- Do not setup or use when tired or when under the influence of alcohol, drugs or medication.
- Do not use for aircraft purposes.
Note that the warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
For assembly, remove the Handle by removing the Bolt (19). Place the Handle on the outside of the Crank and replace the Bolt. It is important to read and understand all instructions and safety information before operating this device. Failure to do so can result in serious injury.
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible.
WARNING
Read this material before using this product. Failure to do so can result in
serious injury. SAVE THIS MANUAL.
Specifications
| Rated Capacity | 1500 lb |
|---|---|
| Length | 16″ |
IMPORTANT SAFETY INFORMATION
-
Study, understand, and follow all instructions before operating this device.
-
Do not exceed rated capacity.
-
Ensure load is secured to the device.
-
To be used only with the following PASE: shop cranes or hoists suitable for load.
-
Failure to heed this information may result in personal injury and/or property damage.
-
Release load-locking devices (if employed) slowly and carefully.
-
No alterations shall be made to this product.
-
Do not allow load to swing or drop violently while lowering or moving.
-
Use as intended only. Do not use for lifting human weight or overhead lifting. Keep clear of raised load.
-
Inspect before every use; do not use if parts are loose or damaged.
-
Wear ANSI-approved safety goggles and heavy-duty work gloves during setup and use.
-
Do not use for aircraft purposes.
-
Do not work underneath, on, or near a lifted load.
-
Maintain product labels and nameplates.
- These carry important safety information.
- If unreadable or missing, contact
- Harbor Freight Tools for a replacement.
-
This product is not a toy.
Keep it out of reach of children. -
Keep bystanders out of the area during use.
-
Do not setup or use when tired or when under the influence of alcohol, drugs or medication.
-
The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors
which cannot be built into this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.
Assembly Instructions
For shipping purposes, the Handle comes installed on the inside of the Crank. It must be reinstalled on the outside of the Crank.
- Remove the Handle by removing the Bolt (19).
- Place the Handle on the outside of the Crank and replace the Bolt.
Operating Instructions
-
Attach the Hanger to a Crane or
Hoist (sold separately). -
Secure the load to the Brackets.
-
Turn the Handle to move the load to its balance point, so that it is hanging evenly from the Leveler.
-
Lower load and detach Leveler after use.
Do not use to support load for extended periods. -
Grease the Threaded Bar (7), as needed, so that the Sliding Block (6) moves smoothly.
Parts List and Diagram
Part| Description| Qty| | Part| Description|
Qty
---|---|---|---|---|---|---
1| Lifting Chain| 1| 12| Bolt (M10x25)| 4
2| Bolt (M12x40)| 1| 13| Lock Nut (M10)| 4
3| Lock Nut (M12)| 2| 14| Cross Beam| 1
4| Bushing| 1| 15| Bolt (M12x45)| 1
5| Connecting Plate| 2| 16| Bushing| 1
6| Sliding Block| 1| 17| Shackle| 2
7| Threaded Bar| 1| 18| Chain/Bracket Set| 4
8| Connecting Plate| 2| 19| Bolt (M10x35)| 1
9| Crank| 1| 20| Nut M10| 1
10| Spring Pin| 2| 21| Handle| 1
11| Bushing| 1| 22| Nut M16| 1
Record Serial Number Here:
Note: If product has no serial number, record month and year of purchase
instead.
Note: Some parts are listed and shown for illustration purposes only, and
are not available individually as replacement parts. Specify UPC 792363674416
when ordering parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet
high quality and durability standards, and warrants to the original purchaser
that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to
damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our
facilities, criminal activity, improper installation, normal wear and tear, or
to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or
consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may
not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation
of the complaint must accompany the merchandise. If our inspection verifies
the defect, we will either repair or replace the product at our election or we
may elect to refund the purchase price if we cannot readily and quickly
provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost
of returning the product. This warranty gives you specific legal rights and
you may also have other rights which vary from state to state.
26677 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797
When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible.
Visit our website at:
http://www.harborfreight.com
Email our technical support at :
productsupport@harborfreight.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>