ALPER Orca 1300 Electric Robotic Pool Cleaner User Manual

ALPER Orca 1300 Electric Robotic Pool Cleaner

Thank you for choosing Aiper robotic pool cleaner.
You have joined millions of people to enjoy the convenience of robotic pool cleaning.
This user manual helps you to keep your robot performing at its best. Please take a few moments to read through it.
If you have any questions, please contact our customer service for assistance or visit www.aiper.com for more information.

Aiper Customer Service
Customer Service Number: US Toll Free: 1-866-850-0666 Email: [email protected] Facebook: @AiperOfficial

Important Precautions

1. Read the manual carefully, and use the cleaner according to the manual. We are not liable for any losses or injuries caused by improper use.
2. To avoid any accidents/damages, it is strongly recommended to fix the power supply unit 11.5ft (3.5m) away from the swimming pool by using the included safety rope.
3. To prevent severe damages to the cleaner, never power on the unit when it is outside of the swimming pool.
4. The power cord must be connected to an appropriate earthed socket and the power connector must be plugged in tightly.
5. Hold the top handle when putting the cleaner into water or lifting out of the water, do not pull the cable. Before powering on, make sure to empty the trapped air inside the cleaner (no more air bubbles come from the cleaner and the cleaner is fully submersed on the pool floor).
6. Before powering on, make sure the filter baskets are assembled in position and the cord is fully released to avoid any winding, which could affect the cleaner’s performance or cause damages.
7. Please clean and wash the filter baskets every time after use.
8. The cleaner should be stored in a cool and ventilated place, away from direct sunlight when it’s not in use.
9. The power supply unit should be placed at a shaded area during working. To avoid overheating and potential damages of components, never cover the power supply unit during working.
10. Only authorized after-sales service personnels can open the cleaner’s power supply unit and motor assembly, otherwise the warranty will be invalidated.
11. Do not use the cleaner beyond the working environment/conditions stated in this manual.
12. Make sure the PH value of the pool water is between 7.0~7.4.
13. This machine is to clean the pool only not for other purposes.
14. Do not use the cleaner immediately after spraying the pool chemicals and do not use the cleaner as a dosing machine, which will damage and corrode the belts.
15. Do not operate the cleaner when there are people or animals in the pool.
16. Take the cleaner out of the swimming pool after use. If the cleaner is immersed in the water for a long time, there will be micro organisms produced.
17. The cord should be untwisted and wrapped properly after use.
18. Use the original adapter only for the control box kit.
19. Do not operate the cleaner while pool filter is running.
20. Do not allow children to ride on the cleaner or play with it.

Introduction

The robotic pool cleaner Orca 1300 is a new type of highly efficient and energy-saving swimming pool cleaning robot. Through its advanced computer- controlled program, it can clean the pool walls and floor automatically. At the same time, it filters the pool water and gets rid of suspended particles without replacing the pool water. It’s totally environmental-friendly.
Read the user manual carefully before use.

Structure

Specifications

Operations Attentions

1. When putting the cleaner into the water, please hold the top handle and make sure to empty the trapped air inside. Now, the cleaner can be immersed to the pool floor.

2. When pulling the cleaner out of the water, suspend the cleaner on the water for about 10-15 seconds to empty the water inside. Please hold the top handle only; never pull the cable.

3. The power supply unit has to be placed in a proper position to reach the distal end of the pool, at least 11.5ft (3.5m) away from the pool edge.

4. Please use the included safety rope to fix the power supply unit in case it drops into the pool.

Control Panel and Indicator Instructions

FiIter Cleaning

A. Slide the two clips according to the indications on the top coverto open it and take out the filters.

B. Clean and wash the filter baskets.

C. Re-install the filters, pay attention to the right position and slide the two clips to close the top cover.

Installation of Foam Floating Blocks
Attention: If your robot is performing well, please ignore these instructions.
The following illustration is limited to the use of white foam blocks to increase coverage when the cleaning machine cannot completely clean and cover the pool area.

Stick the two foams on the internal surface of the top cover (see the picture below). Make sure the two foams are in the middle part of the top cover.

Trouble Shooting

Remark: The pool water condition must be within the following parameters:

• PH: 7.0 —7.4
• Temperature: 10°C(50°F) to 35°C(95°F)
• Salt: Max 5,000 ppm
• Chlorine: Max 2 ppm

Packing List

Warranty

1. This product is covered by Aiper warranty for 24 months ( only for driving kit and control box kit) from the date of purchase. Consum- able parts are beyond warranty including Belts/Filter Baskets/ Rollers/Side Covers.
2. This warranty is voided if the product has been altered, misused, or has been repaired by unauthorized personnels.
3. The warranty extends only to manufacturing defects and does not cover any damage resulting from mishandling of the product by the owner.
4. The order number or record must be presented for any claim or repair during the warranty period.

Aiper Customer Service:
US Toll Free: 1-866-850-0666
Email: [email protected]
Facebook: @AiperOfficial

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>