EMOH HT243-1P26A2P34A Adjustable Sliding Single Rail Panel Track Instruction Manual
- October 30, 2023
- EMOH
Table of Contents
HT243-1P26A2P34A Adjustable Sliding Single Rail Panel Track
Instruction Manual
HT243-1P26A2P34A Adjustable Sliding Single Rail Panel Track
GOOD DESIGN AWARD 2020
Winner of JAPAN JDP
2021 USA MUSE
DESIGN AWARDS SILVER WINNER
2021 USA IDEA
DESIGN AWARDS
| Panel Width | Panel Height |
|---|---|
| 15.75″ | 67.75″ |
| 23.5″ | 91.5″ |
| 31.5″ | 115″ |
These instructions use a 6 panel track as an example; Your installation panel quantity and color may vary. For detailed instructions and maintenance, scan the QR Code or
visit bit.ly/roddesyne-youtube
Tools
Note 1 Drywall Anchor
Drill a 1/4″ pilot hole, hammer the drywall anchor in and mount the brackets
on to the wall with screws.
Note 2 Adjustable Baton for 31.5” panel)
Hold the outer rod, loosen the inner rod to adjust the length. (Inner and
outer poles should overlap at least 2 in.)
Note 2 Finials (Sold Separately)
Remove both end caps and screw the finials onto the cap.
Reattach the assembly into the respective side.
Step 1. Wall Installation
(for ceiling installation, see stept.b)
a-1 Measure the overall coverage needed, including the slider return
position and the optional finials.
a-3 Remove red clip from the sliders.
(During the installation, the clip can be used to keep the sliders in place.)
a-4 Loosen the two screws on the last slider or else the slider cannot be inserted into the rod.
a-5 Extend the rod, make sure the indicator holes are on the outer edges. Also the rod has to be longer than the sliders, then insert the slider into the rod.
a-7 Using the bracket, mark the positions of the screws on the line.
(The left and right most bracket should be 2 to 4 inches away from the edge of
the rod.)
a-8 Drill the pilot hole. Insert the drywall anchor where applicable then screw in a screw on the top hole.
a-9 Loosen the screw on the bracket and turn the clip to the side to access the mounting screws during installation.
a-10 Loosen the screw on the wall enough to slide the bracket onto the screw. Tighten the screws. Screw in a second screw on the bottom of the bracket.
a-11 Twist the clip back to the forward position.
a-12 Adjust the clips to the desired projection. Make sure there is at least a 2″ gap between the center brackets and the edge of the sliders.
a-13 Hook an arm of the bracket’s clip into the groove of the rod, rotate the rod upward in between the arms and rod will snap into place between the clips. Tighten the screw on the clip.
a-14 Move top sliders out of the way. Tighten the locking screws on the last slider.
a-15 Tighten all the screws on the brackets and the installation of the rod is complete.
Step 1.b Ceiling Installation (For wall install see Step 1.a)
IMPORTANT: Finials cannot be used with ceiling installation!
b-1 Do steps a-1, a-2, a-3, a-4, a-5, a-6, a-14.
b-2 Detach the clip from the mount by unscrewing the screw.
b-3 Mark the screw position on the line using a clip. Left and right most clips must be 2-4″ from the end of the rod.
b-4 Drill the pilots holes and insert drywall anchor where applicable.
b-5 Mount the clips onto the ceiling, do not tighten all the way.
b-6 Hook an arm of the bracket’’s clip into the groove of the rod, rotate the rod upward in between the arms and rod will snap into place between the clips. Tighten the screw on the clip.
Reminder: Before you install or remove the track rod, please loosen the
screws first to avoid scratching the finish.
b-7 Tighten all the screws. The ceiling rod installation is complete.
Step 2 Panel Blind Installation (sold separately)
2-1 Push the gates on the sliders up to open the grooves for the panels.
Step 3 Trimming Blinds (Optional)
3-1 Measure the overall installation length. Use the weight as a straight edge to mark the desire length. Trim the blind to size and remove the liner from the scrap.
Note The liner can be reused on average 3 times.
3-2 Put the plastic liner on the bottom of the trimmed panel (1cm from
the edge of fabric)spacing each staple 2″ apart. Hammer the staples flat.
3-3 Cut the extra fabric on both sides along the hem of the panel.
Step 4 Panel Blind Installation
To install the weights, push open the lock on the end caps and remove the end
caps. Slide the liners into the weights and reattach the end caps.
Step 5 Weight Installation
Screw in the baton and the installation is complete.
Draw at 45° for the best results.
Step 6 Windproof Clips Holds the blinds together when windy
6-1 Remove all the end caps on the right side of the blind weights; the last
piece of blind weight remains unchanged
6-2 Replace all removed right end caps with windproof clips
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>