next 653993 CORSICA TV UNIT Wood Fluted Entertainment TV Instruction Manual
- October 30, 2023
- NEXT
Table of Contents
next 653993 CORSICA TV UNIT Wood Fluted Entertainment TV
Product Information: CORSICA TV UNIT
The CORSICA TV UNIT is a self-assembly furniture item that comes with all the necessary fittings and parts required for assembly. It is important to read the assembly instructions carefully before starting the assembly process. The product information and care instructions should also be noted for future reference.
Tools Needed:
- Screwdriver
- Glue
- Allen key (provided)
Product Usage Instructions:
- Insert 10 x cambolts (C) into panels 1, 2 & 3(X2) using a screwdriver until tight.
- Glue and insert 2 x wooden dowels(A) into panel 1.
- Attach panel 1 to panels 3x(2)
- Insert 4 x camlocks (D) into panel 1 and tighten with a screwdriver. Ensuring the arrow indicator is pointing towards the panel edge before tightening with a screwdriver.
- Glue and insert 2 x wooden dowels(A) into panel 1.
- Attach panel 5 to panel 1.
- Insert 1 x camlock (D) into panel 5 and tighten with a screwdriver. Ensuring the arrow indicator is pointing towards the panel edge before tightening with a screwdriver.
- Glue and insert 2 x wooden dowels(A) into panel 2.
- Attach panel 2 to panels 3x(2).
- Insert 4 x camlocks (D) into panel 2 and tighten with a screwdriver.
- Glue and insert 2 x wooden dowels(A) into panel 2.
- Attach panel 6 to panel 2.
- Insert 1 x camlock (D) into panel 6 and tighten with a screwdriver. Ensuring the arrow indicator is pointing towards the panel edge before tightening with a screwdriver.
- Attach panels 4 (x2) to panels 1 & 2 with 8 x screws (E) and tighten with an Allen key (F).
- Carefully upright the assembly unit.
Product Care Instructions:
It is recommended to wipe the CORSICA TV UNIT with a soft, dry cloth for regular cleaning. Avoid using abrasive or chemical cleaners that may damage the surface of the furniture. The product should be kept away from direct sunlight, heat, and moisture. Any replacement fittings or parts can be obtained by contacting
Customer Services Tel: 0333 777 8999.
IMPORTANT – RETAIN FOR FUTURE REFERENCE – READ CAREFULLY.
Tools Needed
Helpline
If you have any problems with this product or require any replacement fittings
please contact Customer Services Tel:
0333 777 8999
Regrettably, self-assembly items cannot be returned once assembly is part or
fully completed unless the item is found to be faulty. Should you need to
return the unassembled product, please repack in the original packaging.
IMPORTANT
- We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
- Carefully check that you have all parts before beginning assembly.
- We recommend that the packaging is used to protect the surfaces during assembly.
- Wall fixings are not included.
- A minimum of two persons is required to assemble this product.
PRODUCT INFORMATION
- Made from hollow board & Honeycomb board, particle board with a wood effect finish.
- Made in China
CARE INSTRUCTIONS
- For general cleaning, periodically dust with a soft cloth.
- Do not rub or scrub the surface when cleaning.
- Do not use furniture polish.
- Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
- Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or damage.
- Do not put hot dishes directly on the surfaces of the item.
- Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discoloration or warping.
- Never drag pieces of furniture across the floor as this will cause damage to the joints.
- All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
FITTINGS
PARTS
STEP ONE
- Insert 10 x cam bolts (C) into panels 1, 2 & 3(X2) using a screwdriver until tight.
STEP TWO
- Glue and insert 2 x wooden dowels(A) into panel 1.
- Attach panel 1 to panels 3x(2)
- Insert 4 x camlocks (D) into panel 1 and tighten with a screwdriver.
Ensuring the arrow indicator is pointing towards the panel edge before tightening with a screwdriver.
STEP THREE
- Glue and insert 2 x wooden dowels(A) into panel 1.
- Attach panel 5 to panel 1.
- Insert 1 x camlock (D) into panel 5 and tighten with a screwdriver.
Ensuring the arrow indicator is pointing towards the panel edge before tightening with a screwdriver.
STEP FOUR
- Glue and insert 2 x wooden dowels(A) into panel 2.
- Attach panel 2 to panels 3x(2)
- Insert 4 x camlocks (D) into panel 2 and tighten with a screwdriver.
- Glue and insert 2 x wooden dowels(A) into panel 2.
- Attach panel 6 to panel 2.
- Insert 1 x camlock (D) into panel 6 and tighten with a screwdriver.
Ensuring the arrow indicator is pointing towards the panel edge before tightening with a screwdriver.
STEP FIVE
- Attach panels 4 (x2) to panels 1 & 2 with 8 x screws (E) and tighten with an Allen key (F) .
- Carefully upright the assembly unit .
Next Retail Ltd, Desford Road, Enderby, Leicester, LE19 4AT