Buck STOVE FF-BRSG Blue Ridge Bent Back Glider Instruction Manual

October 30, 2023
BUCK STOVE

Blue Ridge Bent Back Glider
Instruction Manual
P/N: FF-BRSG Buck STOVE FF-BRSG Blue Ridge Bent Back
Glider

Buck Stove, New Buck Corp |200 Ethan Allen Dr, Spruce Pine, North Carolina
28777, United States | (828) 765-6144 | www.buckstove.com

Included Hardware

Buck STOVE FF-BRSG Blue Ridge Bent Back Glider - Fig

Included Parts

Buck STOVE FF-BRSG Blue Ridge Bent Back Glider - Included
Parts

Required Tools

Buck STOVE FF-BRSG Blue Ridge Bent Back Glider - Required
Tools

Assembly Instructions

Step 1
Unscrew the loosely attached 1.25 in(F) & 1 in(N) screws, and remove the rear cover strip (K) and place aside for final assembly. Step 2
Begin the assembly process by placing the glider in the orientation shown to the right, with the back (I) and seat assembly (J) on their side.

Step 3
Align the holes on the arm assembly (H) with the holesgoing through the back (I) and seat assemblies(J).

Step 4
Insert the 3.5 inch bolt (C) through a washer (D) and into the leg/arm (H), back (I) and seat (J) assemblies.

Step 5
Insert the 2.5 inch bolt (A) through a washer (D) and into the leg/arm (H) and seat (J) assemblies.

Step 6
On the back side of the bolts (A & C) that were inserted through the seat (J), place a washer and then thread a nut onto all of the bolts placed in steps 3-4. Tighten with 7/16 socket and wrench.
Step 7
Place the 3 inch bolt (B) through the leg/arm assembly (H) and the back assembly(I).Buck STOVE FF-BRSG Blue Ridge Bent Back Glider - Included
bolt

Step 8
On the back side of the bolt placed in step 6 (B), place a washer (D) and then thread a nut (E) onto the bolt. Tighten with a 7/16 socket and wrench.
Step 9
Repeat steps 1-7 for other leg/arm assembly (H) of chair.
Step 10
Place the glider in the orientation shown to the right, with the glide assembly (L) underneath.

Step 11
Remove the 3 washers, bolt and nut which is assembled through the bracket on the glide assembly (L). Then place the bolt through the composite with a washer on either side. Slide it though the bracket and place a washer and thread the nut onto the end of the bolt. Tighten til snug with ½ in socket and wrench.
Step 12
Repeat step 11 with the rear bracket on the glide assembly (L).

Step 13
Repeat steps 11 & 12 for both sides of the glider, the glide assembly should be attched at 4 corners with the brackets, and the glider should swing freely.

Step 14
Align the predrilled holes with the rear brace(M) and screw two of the 2 inch(G) screws through the holes and into the brace.

Step 15
Repeat step 14 on both sides of the brace to securely fixture it into place between the two arm/leg(H) assemblies.

Step 16
Attach the front brace (M) in the same manner as the rear using the predrilled holes and included hardware.

Step 17
Align the rear cover strip (K) with the predrilled holes on the back and seat assemblies (I & J).
Step 18
Reattach the rear cover strip removed in Step 1, (K) to the back and seat assemblies (I & J) using the provided 1.25 inch (F) and 1 inch screws (N). The screws are a #2 Square bit.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals