ZDU ZP930-A 3.1 Inch LCD VA Black Film Color Screen User Manual

ZDU ZP930-A 3.1 Inch LCD VA Black Film Color Screen

Product Information

The ZP930-A product is equipped with a 3.1-inch LCD VA black film color screen with light buttons and a matte textured black finish. The instrument interface has a clear and intuitive functional area distribution, and the high- brightness LED backlight makes the display content visible even in sunlight. The product is made of nylon buckle, ABS shell, hardened PC mirror waterproof glass and can be used normally in temperatures ranging from -25 to 80 degrees Celsius. It ensures good electrical and mechanical performance.

Function

1. Battery indicator, Malfunction indicator, Gear indicator, Speed indicator, Cruise indicator, Headlight icon, 6KM boost indicator, Unit indicator and Bluetooth icon display.
2. Communication protocol: UART
3. Contents on the display:
   • Speed & Power display, The Maximum display to 199KM/H
   • Voltage status level
   • Multifunctional display area:
   • Total mileage
   • Single mileage
   • Real-time voltage display
   • Running time prompt
   • Fault prompt
   • Switch handle voltage value
   • Fault status display area: Displays the fault content corresponding to the number in the multifunction area. The specific status is as follows:
   • ERRO 1: Motor failure
   • ERRO 2: Accelerator throttle failure
   • ERRO 3: Controller failure
   • ERRO 4: Brake failure
   • ERRO 5: Under voltage protection
   • ERRO 6: Communication failure, the display cannot receive the output from the controller
   • ERRO 7: Communication failure, the controller cannot receive the output from the display
   • Gear display
   • Single/dual drive riding mode selection, the default mode is single drive:
   • S-drive: One motor drive
   • D-drive: Two motors drive
   • Starting mode of the scooter:
   • ECO: Non-zero startup mode
   • Accessibility display:
   • NORMAL: Zero startup mode
   • Cruise mode / 6KM boost mode / Headlights on reminder
   • USB charging prompt (Not supported) / Bluetooth connection status prompt USB (Not supported)

Key Functions

• ON/OFF Button: POWER ON/POWER OFF
  • Press and hold the ON/OFF button for 3 seconds to turn on/off.
  • Short press the ON/OFF button to turn on/off the headlight.
• UP Button: GEAR UP
  • Short press the UP button to increase the gear.
  • Press and hold the UP button to enable/disable dual drive mode.
• DW Button: GEAR DOWN
  • Short press the DW button to downshift.
  • Long press the DW button to enter/exit the 6KM boost mode (need to be supported by a controller).
• Function menu settings: Press the UP button & DW button at the same time to enter the function menu interface. Short press the ON/OFF button to switch function options, short press the UP button or DW button to set the corresponding parameter value. After the setting is completed, press the UP & DW button at the same time to exit.
  • Enter the menu, short press the plus or minus key, the value 00099 flashes, and the display returns to the main interface after long-pressing the plus key for 5 seconds, the setting is successfully done.

Product Usage Instructions

1. To turn on/off the product, press and hold the ON/OFF button for 3 seconds.
2. To turn on/off the headlight, short press the ON/OFF button.
3. To increase the gear, short press the UP button.
4. To enable/disable dual drive mode, press and hold the UP button.
5. To downshift, short press the DW button.
6. To enter/exit the 6KM boost mode, long press the DW button (need to be supported by a controller).
7. To enter the function menu interface, press the UP button & DW button at the same time. Short press the ON/OFF button to switch function options, short press the UP button or DW button to set the corresponding parameter value. After the setting is completed, press the UP & DW button at the same time to exit.
8. To view the product display, refer to the product information section for a detailed description of the display content.

Product Introduction
The ZP930-A product adopts a 3.1-inch LCD VA black film color screen, with light buttons, matte textured black . The functional area distribution of the instrument interface is clear and intuitive, and the high-brightness LED backlight is selected, and the display content is still clearly visible in the sun. The product adopts nylon buckle, ABS shell, hardened PC mirror waterproof glass, the product can be used normally in the temperature of -25℃-80℃, and can ensure good electrical performance and mechanical performance.

FUNCTION

1. Display function
   Battery indicator, Malfunction indicator ,Gear indicator, Speed indicator, Cruise indicator, Headlight icon, 6KM boost indicator, Unit indicator and Bluetooth icon display.

2. Communication protocol: UART

3. Contents on the display

Display content introduction

1. Speed & Power display, The Maximum display to 199KM/H

2. Voltage status level
   From bottom to top, the battery level increases sequentially, the lowermost display grid represents low battery, and the uppermost display grid represents high battery. The left side displays the corresponding remaining battery percentage (percentage example display)

3. Multifunctional display area
   
   Display: total mileage, single mileage, real-time voltage display, running time prompt, fault prompt, switch handle voltage value

4. Fault status display area
   The number corresponding to the multi-function area represents the corresponding fault content. The specific status is as follows

5. ERRO 1：Motor failure

6. ERRO 2：Accelerator throttle failure

7. ERRO 3：Controller failure

8. ERRO 4: Brake failure

9. ERRO 5：Undervoltage protection

10. ERRO 6：Communication failure, the display cannot receive the output from the controller

11. ERRO 7：Communication failure, the controller cannot receive the output from the display

12. **Gear display

**

6. Single/dual drive riding mode selection, the default mode is single drive

7. S-drive: One motor drive

8. D-drive: Two motors drive

9. **Starting mode of the scooter

**

1.  **ECO:** Non-zero startup mode
2.  **NORMAL:** Zero startup mode

8. Accessibility display
   

9. Cruise mode

10. 6KM boost mode

11. Headlights on reminder

• USB charging prompt (Not supported)
• Bluetooth connection status prompt USB (Not supported)

**INTRODUCTION TO KEY FUNCTIONS

**

1. ON/OFF Button : POWER ON/POWER OFF

2. Press and hold the ON, OFF button for 3 seconds to turn on/off.

3. Short press the ON/OFF button to turn on/off the headlight.

4. UP Button： GEAR UP

5. Short press the UP button to increase the gear

6. Press and hold the UP button to enable/disable dual drive mode.

7. DW Button: GEAR DOWN

8. Short press the DW button to downshift

9. Long press the DW button to enter/exit the 6KM boost mode (need to be supported by a controller)

10. Function menu settings
    Press the UP button & DW button at the same time to enter the function menu interface. Short press the ON/OFF button to switch function options, short press the UP button or DW button to set the corresponding parameter value. After the setting is completed, press the UP& DW button at the same time to exit.

11. Parameter setting and definition

12. P02：mileage unit，0：KM；1：MILE； default: 0

13. P03：Voltage mode； default: 60V

14. P04：Sleep time： from 0-60mins（0 means always on ,default: 5mins)

15. P06: Wheel diameter calculated by inch；precision：0.1； default: 10

16. P07:Number of tachometer magnets：Range：1-100； Default: 30

17. P09：Zero start/non-zero start settings，0：Zero start；1：Non-zero start ；Default: 1

18. P10：Smart speed limit settings, 0:Speed released, 1:Speed locked Default: 1

19. P12：Activate strength setting. Range: from 0 to 5， 5 most power Default: 5

20. P15：Motor drive signal percentage setting, Range: from 1 to 100; Default: 100

21. P16：Auto cruise setting， 1:Auto cruise Activated 0 Auto cruise Locked ； Default: 0

22. P99：Restore to initial settings

Enter the menu, short press the plus or minus key, the value 00099 flashes, and the display returns to the main interface after long-pressing the plus key for 5 seconds, the setting is successfully done.

ODO: To clear ODO
In the ODO parameter setting interface, briefly press the + button and then press and hold for 5-6 seconds until the number is zero.

INTRODUCTION OF CONNECTORS AND DEFINITIONS

• Connector 1: 3P-accelerator interface
• Connector 2: 4P-Three-position button interface
• Connector 3: 6p-Instrument connection controller interface
• Connector 4&5: 2P-brake interface
  

Note: Due to the upgrade of the company’s products, the displayed content of the product you get may be different from the manual, but it will not affect your normal use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>