YUKON 58832 Three Drawer Hardwood Workbench Owner’s Manual

YUKON 58832 Three Drawer Hardwood Workbench

Product Information

The Workbench is a sturdy and durable work surface designed for indoor use only. It is capable of supporting a certain weight capacity, and it is important to evenly distribute the load on the table to avoid tipping. The product comes with a parts list and diagram, assembly instructions, and a warranty for future reference. The Workbench should only be used for its intended purpose and should not be used to perform tasks for which it was not designed.

Specifications

• Item number: 58832
• Weight capacity: check user manual for details
• For indoor use only

Important Safety Information

Read all safety warnings and instructions before using the Workbench. Failure to follow the warnings and instructions may result in serious injury. Save all warnings and instructions for future reference.

Warning Symbols and Definitions

The following symbols are used to alert you to potential personal injury hazards:

• A safety alert symbol indicates a hazardous situation which, if not avoided, will result in death or serious injury.
• A hazardous situation symbol indicates a hazardous situation which, if not avoided, could result in death or serious injury.
• A hazardous situation symbol indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• A symbol that addresses practices not related to personal injury.

Setup

1. When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible.
2. Use only on flat, level, and hard surfaces capable of supporting the Workbench and any items placed on the Workbench.
3. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly and use.
4. Keep bystanders out of the area during assembly.
5. Do not assemble when tired or under the influence of drugs or medication.

Operation

1. Do not exceed weight capacity for the Workbench.
2. Sudden load movement may briefly create excess load causing product failure.
3. Use as intended only. Do not use Workbench to perform tasks for which it was not designed.
4. Inspect before every use; do not use if parts are loose or damaged.

Maintenance

1. Keep assembly area clean and well-lit.
2. Maintain product labels and nameplates. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement.

WARNING Symbols AND DEFINITIONS

| This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
| Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
| Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
| Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
| Addresses practices not related to personal injury.

IMPORTANT SAFETY INFORMATION

Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in serious injury. Save all warnings and instructions for future reference.

1. Do not exceed weight capacity for the Workbench. Be aware of dynamic loading! Sudden load movement may briefly create excess load causing product failure.
2. Use only on flat, level and hard surface capable of supporting the Workbench and any item(s) placed on Workbench. Evenly distribute load on Table to avoid tipping.
3. Use as intended only. Do not use Workbench to perform task for which it was not designed.
4. For indoor use only.
5. Assemble only according to these instructions. Improper assembly can create hazards.
6. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly and use.
7. Keep assembly area clean and well lit.
8. Keep bystanders out of the area during assembly.
9. Do not assemble when tired or when under the influence of drugs or medication.
10. This product is not a toy. Do not allow children to play with, on or near Workbench.
11. Inspect before every use; do not use if parts are loose or damaged.
12. Maintain product labels and nameplates. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement.

Specifications

Assembly Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
Note: For additional information regarding the parts listed in the following pages, refer to Parts List and Diagram on page 10.
Note: More than one person is needed for proper assembly.

1. Insert Connecting Nuts (8) into holes at ends of a Cross Brace (3). Make sure that the slots on the Nuts align horizontally. This will allow the Bolts to be threaded into the Cross Brace in the next step.

2. Set the Cross Brace against a Leg (4) and use the Hex Key (9) and 60 mm Bolts (7) to fasten the Cross Brace and Leg together.
   NOTE: Make sure the groove in the Cross Brace is facing IN.

3. Repeat Step 2 for the second Leg (4).

4. Once both Legs have been fastened to the Cross Brace, slide the Bottom Shelf (2) between the Legs so that the far edge fits onto the groove on the Cross Brace.

5. Set the second Cross Brace against the other edge of the Bottom Shelf.

6. Once the Cross Brace is in place and the mounting holes on the Legs are aligned with the Connecting Nuts in the Cross Brace, use the Hex Key and Connecting Bolts to fasten the second Cross Brace to both Legs.

7. With assistance, place the Table Top (1) face down on a smooth, padded surface. This will allow installation of the sliding drawers.

8. Set the Sliding Partition (14) into place by inserting the tabs at the end of the Partition into the holes at the center of the Table Top’s underside.
   Note: Verify that the Sliding Partition and Table Top face the same direction.

9. Use 35mm Screws (13) to fasten the Sliding Partition to the middle of the Table Top’s underside.

10. With assistance, set the assembled Legs and Bottom Shelf onto the underside of the Table Top.
    Note: When setting down the assembled Legs onto the Table Top, verify both Legs and Table Top are facing the correct direction.
    Note: Verify that the Drawer guide slots on the Sliding Partition face the same way as the Drawer guide slots on the Legs.

11. Use the Hex Key and 60mm Bolts (7) to fasten the Legs to the Table Top underside, using two Screws per side.

12. Use the 50mm Screws (6) to fasten legs (4) to Table Top’s underside per side.

13. Attach the Middle Cross Brace (15) to the Legs (4) above Sliding Partition (14) with 35mm Screws (13).

14. With assistance, set the assembled frame right-side up where desired.

15. Remove the Vise Screw/Washer (12) from the middle threaded rod of the Vise (5).
    Note: Install Vise with slots facing up.

16. With the Vise Screw/Washer removed, slide the Vise into the three holes on the side of the Workbench.

17. Use the Vise handle to thread in the Vise all the way and re-install the Vise Screw/Washer. This will keep the Vise locked in place on the side of the Workbench.

18. Use the Drawer Bolts (22) to fasten the Drawer Handles (21) to the Drawer Front Panels (16).
    Note: Each Drawer piece should have a sticker designating what it is. Use the Parts List on page 10 as a reference. This will help insure correct assembly.

19. Fasten a Left Drawer Slot Panel (18) and a Right Drawer Slot Panel (19) to a Drawer Front Panel (16).

20. With the felt side up, slide a Drawer Bottom (3) into the grooves along the insides of the assembled Left and Right Drawer Slot Panels from the previous Step. Fasten a Drawer Back Panel (17) to the ends of the two Slot Panels, then fasten Drawer Bottom to Drawer Back Panel.

21. Repeat Steps 19 and 20 for the bottom drawer. Once Drawer is fully assembled, verify that the inside tracks along the Legs and Sliding Partition are pushed forward.

22. Slide Drawers into tracks along Sliding Partition and insides of the Legs.

23. Once all Drawers are inserted, tap Wood Pegs (10) and Anvil Pegs (11) into desired holes on the Table Top. The Workbench is now fully assembled and ready for use.

Operation Instructions

1. Place Anvil Pegs (1) into Vise (5) slots and Table Top (1) slots to firmly hold work piece into position. Anvil Pegs can be used with Wood Pegs (19).

2. Place Wood Pegs into Vise slots and Table Top slots to firmly hold work piece into position. Wood Pegs can be used with Anvil Pegs.

Maintenance and Servicing

Procedures not specifically explained in this manual must be performed only by a qualified technician.

• TO PREVENT SERIOUS INJURY FROM ACC IDENTAL OPERATION: Turn the Power Switch of the tool off and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures.
• TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.

Cleaning, Maintenance, and Lubrication

1. BEFORE EACH USE , inspect the general condition of the Workbench. Check for
   • loose hardware
   • misalignment or binding of parts
   • cracked or broken parts
   • any other condition that may affect its safe operation.
2. AFTER USE , wipe external surfaces of the Workbench with clean cloth.

Parts List and Diagram

PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Parts List

Note: A few pieces of extra hardware may be included.

Assembly Diagram

Record Product’s Serial Number Here:____
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Specify UPC 193175486363 when ordering parts.

Limited 90 Day Warranty

• Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
• To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.
• This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

26677 Agoura Road
Calabasas, CA 91302
1-888-866-5797
Item 58832 For technical questions, please call 1-888-866-5797.
Visit our website at: http://www.harborfreight.com
Email our technical support at : productsupport@harborfreight.com
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. 22h When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible.
Copyright© 2022 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>