VISION FIRES VS150 Solus Electric Fire Instruction Manual

VISION FIRES VS150 Solus Electric Fire

Product Information

• Product Name: Solus Electric Fire SE150 REV B 06/22
• Components: Top Shelf, Bottom Shelf, Floor Plinth
• Assembly type: Cam Lock and Screw Pin
• Number of Cam Locks: X32
• Number of Screw Pins: X32

Product Usage Instructions

Bottom Shelf Assembly:

1. Take the bottom panel and ensure the arrows on the top face of the 10 cam locks face outwards towards the edge of the board. Then using a screwdriver, carefully fit 4 screw pins into the small holes being careful not to over-tighten.
2. Take a side panel and ensure the arrows on the top face of the 4 cam locks face outwards towards the edge of the board. Then using a screwdriver, carefully fit 2 screw pins into the small holes being careful not to over-tighten. Repeat this with the second side panel.
3. Take one side panel and push the 2 screw pins into the holes located on the side of the bottom panel. Use a screwdriver to turn the relevant cam locks clockwise to secure the side component to the bottom component. Repeat this with the second side panel.
4. Take a support panel and ensure the arrows on the top face of the 4 cam locks face outwards towards the edge of the board then position it onto 2 of the screws located on the bottom panel. Turn the 2 bottom cam locks clockwise to secure the support panel to the bottom panel. Repeat this with the second support panel.
5. Take the front panel and ensure the arrows on the top face of the 6 cam locks face outwards towards the edge of the board. Then using a screwdriver, carefully fit 10 screw pins into the small holes being careful not to over-tighten.
6. Offer the front panel up to the rest of the assembly, ensuring that the 10 screw pins locate into the small holes on the bottom and side panels. Turn the 10 relevant cam locks on the bottom and side panels clockwise to secure the front panel.
7. Take the top panel and using a screwdriver, carefully fit 14 screw pins into the small holes being careful not to over tighten.
8. Carefully place the top panel onto the rest of the assembly, ensuring that the 14 screw pins locate into the small holes on the front, side, and support panels. Turn the 14 relevant cam locks clockwise to secure the top panel.

Floor Plinth Assembly:

1. Take the assembled Bottom Shelf and turn it upside down. Then using a screwdriver, carefully fit 12 screw pins into the small holes located on the underside being careful not to over-tighten.
2. Take the rear panel and ensure the arrows on the top face of the 4 cam locks face outwards towards the edge of the board. Then using a screwdriver, carefully fit 2 screw pins into the small holes being careful not to over-tighten.
3. Take a side panel and ensure the arrows on the top face of the 4 cam locks face outwards towards the edge of the board. Then using a screwdriver, carefully fit 2 screw pins into the small holes being careful not to over-tighten. Repeat this with the second side panel.
4. Attach the side panels to the rear panel by pushing the 2 screw pins into the holes located on the side of the rear panel. Use a screwdriver to turn the relevant cam locks clockwise to secure the side components to the rear component.
5. Carefully place the assembled Bottom Shelf onto the floor plinth, ensuring that the 12 screw pins locate into the small holes on the underside of the plinth. Turn the 12 relevant cam locks clockwise to secure the Bottom Shelf to the plinth.

BOTTOM SHELF CONTENTS

BOTTOM SHELF ASSEMBLY

1. Take the bottom panel and ensure the arrows on the top face of the 10 cam locks face outwards towards the edge of the board. Then using a screwdriver, carefully fit 4 screw pins into the small holes being careful not to over tighten.
2. Take a side panel and ensure the arrows on the top face of the 4 cam locks face outwards towards the edge of the board. Then using a screwdriver, carefully fit 2 screw pins into the small holes being careful not to over tighten. Repeat this with the second side panel.
3. Take one side panel and push the 2 screw pins into the holes located on the side of the bottom panel. Use a screwdriver to turn the relevant cam locks clockwise to secure the side component to the bottom component. Repeat this with the second side panel
4. Take a support panel and ensure the arrows on the top face of the 4 cam locks face outwards towards the edge of the board then position it onto 2 of the screws located on the bottom panel. Turn the 2 bottom cam locks clockwise to secure the support panel to the bottom panel. Repeat this with the second support panel.
5. Take the front panel and ensure the arrows on the top face of the 6 cam locks face outwards towards the edge of the board. Then using a screwdriver, carefully fit 10 screw pins into the small holes being careful not to over tighten.
6. Offer the front panel up to the rest of the of the assembly, ensuring that the 10 screw pins locate into the small holes on the bottom and side panels. Turn the 10 relevant cam locks on the bottom and side panels clockwise to secure the front panel.
7. Take the top panel and using a screwdriver, carefully fit 14 screw pins into the small holes being careful not to over tighten.
8. Offer the top panel up to the rest of the of the assembly, ensuring that the 14 screw pins locate into the small holes on the bottom and side panels. Turn the 14 relevant cam locks on the front, side and support panels clockwise to secure the top panel.

FLOOR PLINTH CONTENTS

FLOOR PLINTH ASSEMBLY

1. Take the assembled Bottom Shelf and turn upside down. Then using a screwdriver, carefully fit 12 screw pins into the small holes located on the underside being careful not to over tighten.
2. Take the rear panel and ensure the arrows on the top face of the 4 cam locks face outwards towards the edge of the board. Then using a screwdriver, carefully fit 2 screw pins into the small holes being careful not to over tighten.
3. Take a side panel and ensure the arrows on the top face of the 4 cam locks face outwards towards the edge of the board. Then using a screwdriver, carefully fit 2 screw pins into the small holes being careful not to over tighten. Repeat this with the second side panel.
4. Take the central support panel and position it onto 2 of the screws located on the rear panel. Ensure that the arrows on the top face of the 6 cam locks are pointing outwards towards the edge of the panel. Turn the 2 rear cam locks clockwise to secure the central support panel to the rear panel
5. Take the front panel and ensure the arrows on the top face of the 6 cam locks face outwards towards the edge of the board. Then using a screwdriver, carefully fit 6 screw pins into the small holes being careful not to over tighten.
6. Offer the front panel up to the rest of the of the assembly, ensuring that the 6 screw pins locate into the small holes on the side and central support panels. Turn the 6 relevant cam locks on the side and central support panels clockwise to secure the front panel.
7. Carefully lower the assembled bottom shelf onto the assembled floor plinth, ensuring that the 12 screw pins locate into the small holes on the side panels, front panel and central support panel. Turn the 12 relevant cam locks on the side, front and central support panels clockwise to secure the top panel.

TOP SHELF CONTENTS

TOP SHELF ASSEMBLY

1. Take the bottom panel and ensure the arrows on the top face of the 10 cam locks face outwards towards the edge of the board. Then using a screwdriver, carefully fit 4 screw pins into the small holes being careful not to over tighten.
2. Take a side panel and ensure the arrows on the top face of the 4 cam locks face outwards towards the edge of the board. Then using a screwdriver, carefully fit 2 screw pins into the small holes being careful not to over tighten. Repeat this with the second side panel
3. Take one side panel and push the 2 screw pins into the holes located on the side of the bottom panel. Use a screwdriver to turn the relevant cam locks clockwise to secure the side component to the bottom component. Repeat this with the second side panel
4. Take a support panel and ensure the arrows on the top face of the 4 cam locks face outwards towards the edge of the board then position it onto 2 of the screws located on the bottom panel. Turn the 2 bottom cam locks clockwise to secure the support panel to the bottom panel. Repeat this with the second support panel.
5. Take the front panel and ensure the arrows on the top face of the 6 cam locks face outwards towards the edge of the board. Then using a screwdriver, carefully fit 10 screw pins into the small holes being careful not to over tighten.
6. Offer the front panel up to the rest of the of the assembly, ensuring that the 10 screw pins locate into the small holes on the bottom and side panels. Turn the 10 relevant cam locks on the bottom and side panels clockwise to secure the front panel
7. Take the top panel and using a screwdriver, carefully fit 14 screw pins into the small holes being careful not to over tighten.
8. Offer the top panel up to the rest of the of the assembly, ensuring that the 14 screw pins locate into the small holes on the bottom and side panels. Turn the 14 relevant cam locks on the front, side and support panels clockwise to secure the top panel.

WWW.VISIONFIRES.CO.UK

References

• Vision Fires

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>