BOSCH Indego 700 Robotic Lawnmowers Instruction Manual

Indego M 700 | Indego M+ 700
Original instructions

Indego 700 Robotic Lawnmowers

Thank you,
for purchasing the Indego Robotic Mower.
Please read the safety instructions provided below before installing the Indego.

Safety Notes

Warning! Read all safety warnings and all instructions. Make yourself familiar with the controls and the proper use of the machine. Please keep the instructions safe for later use!

Explanation of symbols on the machine

| General hazard safety alert.
Ensure no exits are blocked or obstructed by the machine.
---|---
****| Warning: Read user instructions before operating the product.
| Warning: Operate the isolator switch before working on or lifting the machine.
| Caution: Do not touch rotating blades. The blades are sharp. Beware of severing toes or fingers.
| Wait until all machine components have completely stopped before touching them. The blades continue to rotate after the machine is switched off, a rotating blade can cause injury.
| Make sure that bystanders are not injured by foreign objects being thrown away.
| Warning: Keep a safe distance to the product when operating.
| Do not ride on the machine.
| Battery charger contains a safety transformer.
| Do not use a high-pressure washer or a garden hose to clean the machine.

Operation

• Before working on the mower itself (e. g. maintenance, tool change, etc.) as well as during transport and storage, switch off the mower by the isolator switch.

• Children should be supervised to ensure that they do not play with the machine.

•  Never allow children, persons with physical, sensory or mental limitations or a lack of experience and/or knowledge and/or people unfamiliar with these instructions to use the product. Local regulations may restrict the age of the operator.

• Do not operate the machine when barefoot or wearing open sandals, always wear substantial footwear and long trousers.

• Operate the machine only when the battery compartment is shut with the cover and all the screws in place.
  This protects the battery against moisture.

• Avoid mowing in bad weather conditions especially when there is a risk of lightning.

• While operating and as well while approaching the mower, take sufficient precaution to keep balance at all times particularly on slopes and wet grass. Do not stretch yourself too much forwards. Do not operate the mower in a rush.

• The user is responsible for accidents or hazards occurring to other people or their property.

• If any hazard occurs whilst the machine is operating immediately press the red STOPbutton.

• Ensure correct installation of the perimeter wire as instructed in the installation guide.
  For complete instructions on the Indego installation, please refer to the Installation Guide provided with the product.

• Periodically inspect the area where the mower is used and remove all stones, sticks, wires and other foreign objects.

• Thoroughly inspect the area, for which the garden tool is to be used, for wild animals and pets. Wild animals and pets can be injured by the machine during operation.

• Do not run any live mains cables in the working area. If a mains cable becomes entangled in the robotic mower it must be isolated before any attempt to remove it.

• Periodically inspect to see that the blades, blade bolts and cutter assembly are not worn or damaged.
  Replace worn or damaged blades and bolts in sets to preserve balance.

• Never operate the machine with defective guards or without safety devices.

• Do not put hands or feet near or under rotating parts.

• Never pick up or carry the machine while the motor is running.

• Do not leave the machine to operate unattended if you know that there are pets, children or people in the immediate vicinity.

• Start the machine according to the instructions standing well away from rotating parts.

• Do not use the product at the same time as a sprinkler or use the schedule to ensure that the two systems never run simultaneously.

• If for any reason the product is submerged, take it away from water and turn it off using the isolator switch.
  Do not attempt to switch the product on but contact your Bosch Service Centre.

• Do not modify this product. Unauthorized modifications may impair the safety of your product and may result in increased noise and vibration.

Turn off the product using the isolator switch:

• before clearing a blockage,
• before checking, cleaning or working on the machine,
• before storage
• if the machine vibrates abnormally (stop and check immediately),
• after striking a foreign object, inspect the machine for damage and get advice on necessary repairs from your Bosch Service Centre.

Maintenance

• Always wear gardening gloves when handling or working near the sharp blades.
• Before working on the mower, turn it off using the isolator switch.
• Before working on the docking station or power supply, remove plug from mains.

Clean the exterior of the machine thoroughly using a soft brush and cloth. Do not use water, solvents or polishes. Remove all grass and debris, especially from the ventilation slots. Turn the mower upside down and clean the blade area and the swivel castors regularly. Use a stiff brush or scraper to remove compacted grass clippings (see figure I).
Blades are reversible.

• Make sure all nuts, bolts and screws are tight to ensure safe working with the garden tool. (see figure J)
• Periodically visually inspect the machine and replace worn or damaged parts for safety.
• Ensure that only official Bosch replacement parts are used.
• Replace all blades and bolts as a set as required.

Storage in winter

• Turn off the mower using the isol ator switch.
• The mower will operate between 5 °C and 45 °C. During the winter season once the temperature in the garden is consistently below 5 °C store the mower and the docking station in a secure, dry place, out of the reach of children.

Do not place other objects on the mower or docking station.
It is recommended to use the original packaging when transporting the Indego over long distances.
The mower can also be stored using the storage bag.

• Store the mower only within a temperature range between –20 °C and 50 °C. As an example, do not leave the mower in the car in summer.

USB

• The mower has a USB interface which is to be used exclusively for software updates (see figure M). Use only approved USB.org sticks (formatted to FAT 32) and approved USB.org OTG cables.
• More details about software updates can be found at Bosch-Indego.com.
• Do not use the USB interface for any additional purposes. Do not plug any external devices.

Recommendations for Optimal Handling of the Battery Pack

• Do not open the battery. There is a risk of short-circuiting.
  Protect the battery against heat (e.g., against continuous intense sunlight), fire, water, and moisture. There is a risk of explosion.

• Keep any unfitted battery away from paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

• In case of damage and improper use of the battery pack, vapours may be emitted. Ventilate the area and seek medical help in case of complaints. The vapours can irritate the respiratory system.

• The battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally. An internal short circuit can occur and the battery can burn, smoke, explode or overheat.

• If used incorrectly or if the battery is damaged, flammable liquid may be ejected from the battery. Contact with this liquid should be avoided. If contact accidentally occurs, rinse off with water. If the liquid comes into contact with your eyes, seek additional medical attention. Liquid ejected from the battery may cause irritation or burns.

• Do not short-circuit the battery. There is a risk of explosion.

• Use only Bosch battery packs in- tended specifically for the ma- chine. Use of any other battery packs may create a risk of injury and fire.

• Ensure the switch is in the off posi- tion before inserting battery. In- serting the battery pack into ma- chines that have the switch on can cause accidents.

• Only open the battery compartment when the battery is exhausted. Leave the battery in the machine for storage in winter. The built-in battery is very long-lasting; do not open the battery compartment until you notice a significant reduction in the run time between two battery charging procedures.

• The Indego will operate between 5 °C and 45 °C. If the battery temperature is outside this range, the Indego will display a message and will not leave the docking station. If operating, the Indego will return to the docking sta- tion or stay in place.

• Recharge only in the Bosch ap- proved docking station.

Safety Warnings for Docking Station and Power Supply

• Only use the original Bosch dock- ing station and power cord to charge the mower. Otherwise there is danger of fire and explosion.
• Check the docking station, power supply unit, cables and plugs peri- odically. If damage or ageing is de- tected, isolate from the docking station or power supply and do not use them. Never open the docking station or power supply yourself. Have repairs performed only by a qualified Bosch technician and only using original spare parts. A damaged docking station, power supply, cable or plug increases the risk of an electric shock.
• Do not operate the docking station and power supply on easily flam-mable surfaces (e. g., paper, tex- tiles, etc.) or surroundings. The heating of the docking station and power supply during the charging process can pose a fire hazard.
• Supervise children at all times. This will ensure that children do not play with the docking station, power supply or the machine.
• The voltage indicated on the power supply must correspond to the voltage of the power source.
• We recommend that the power sup- ply is only connected into a socket which is protected by a circuit- breaker that would be actuated by a 30 mA residual current. Check your Residual Current Device (RCD) at regular intervals.
• The supply cord must be inspected for signs of damage at regular inter- vals.
• In the event of flooding of the dock- ing station turn off power supply at mains and contact Bosch Service Centre.
• Never touch the mains plug or any other plugs with wet hands.
• Do not run over, crush or pull the cables. Protect the cables from heat, oil and sharp edges.

The power supply is double insulated for safety and requires no earth con- nection. The operating voltage is 230 V AC, 50 Hz (for non-EU countries 220 V, 240 V as applicable). Contact your Bosch Service Centre for details. If in doubt contact a qualified electrician or the nearest Bosch Service Centre.

Symbols

The following symbols are important for reading and under- standing the operating instructions especially the diagrams. Please take note of the symbols and their meaning. The cor- rect interpretation of the symbols will help you to use the garden product in a better and safer manner.

Intended Use

The mower is intended for domestic lawn mowing.
Do not operate the mower indoors.
Do not use the mower for any other purpose because of the increased risk of accidents and damage to the mower. Never attempt to modify the mower in any way since this may result in accidents or damage to the mower.

Technical Data

Robotic Lawnmower| SI Unit| Indego M 700| Indego M+ 700
---|---|---|---
Article number|  | 3 600 HB0 2..| 3 600 HB0 3..
Cutting width| cm| 19| 19
Height of cut| mm| 30-50| 30-50
Slope angle (max.)| °/%| 15/27| 15/27

Size of lawn area

Perimeter wire

Docking station

Power supply unit
Article number

A) Depends on cutting height, grass conditions and moisture
B) Internal battery temperature

Noise/Vibration Information

Noise emission values determined according to EN 50636-2-107.
Typically the A-weighted noise levels of the product are: Sound power level 61 dB(A). Uncertainty K = 2 dB.

Explanation of Figures

– with additional docking station (right)
– without additional docking station (top left)| L| 436
---|---|---
Software update| M| 437−438
Power supply unit connection| N| 439

Installation

For a video guide on how to install the mower, please visit www.bosch- indego.com or use the following QR-Code. Alternatively, follow the Installation Guide delivered with the product.

https://www.bosch-garden.com/gb/en/garden-tools/indego-home.jsp

Check if the perimeter wire is fully pegged to the ground avoiding any slack lengths of wire. Any loose wire can be a trip hazard.
Remove stones, loose pieces of wood, wire, live mains cables and other foreign objects from the cutting area.
Make sure that the cutting area is even and has no ditches, grooves and steep slopes above 15°/27 %, which are clear obstructions for the mower.
The docking station must be positioned on the wire at an outer edge of the cutting area. It may not be positioned on the side of a tool or garden shed standing as an island within the lawn to be mowed.
It is recommended that you mow your lawn once with a conventional lawnmower before installing and before the first mowing of the new season and whenever the grass clippings would be longer than 5 mm.
The mower’s cutting system is designed to cut small lengths of grass (30–50 mm). The clippings can remain as mulch to fertilize the lawn. The height of cut for mower can be adjusted to 30, 40 and 50 mm.
It is recommended to start with a higher setting and then gradually decrease the height of cut as the wire disappears under the grass. This prevents your Indego from cutting the wire.
Additional perimeter wire can be added using a wire connector (see figures D–E).
The perimeter wire can be extended up to a maximum length of 350 m.
The perimeter wire can be buried up to 5 cm under the ground (or under non- metallic slabs).
To avoid causing damage to the perimeter wire, do not verticut or rake the area where it is positioned.
When laying out the wire avoid angles of less than 45°.
This can affect the performance.
Display

If the confirm button is pressed whilst mowing, the mower will return to the docking station
3| | Red LED on: mower error
4| | Green LED on: mower is switched on Green LED off: The mower is inactive and your four-digit PIN code is required for activation.
Or the mower is shut off, the isolator switch must be turned on and your four digit PIN code must be entered to activate the mower.
Note: during a software update, the green LED and red LED will be on.
5| | Left/right button
6| | Down/up button
7|  | Display with dialog screen
8|

1,2,3

| Garden number (shown when more than
one garden map in the mower memory)
Only with Indego M+ 700:
9| | Network signal present
| Network signal absent

The display switches into sleep mode, if no input is made for 10 minutes.
Adding a further Garden/Lawn Area (see figure K)
To install the Indego to an additional lawn area, please follow the instructions in the Installation Guide.
Separate garden with separate docking station (see figure K, right side): The mower can be used on up to three different gardens. For an additional garden, a separate docking station (see figure A) and the necessary perimeter wire and pegs are required. If a schedule or the “Bosch AUTO” calendar function or the Bosch ”SmartMowing” functionality is set, the grass of the area it is in will be cut, within the defined time slots.
Switch off the mower when transporting it between the individual gardens.
Note: software updates have to be carried out on the mower in every docking station.
To ensure remembering which docking station belongs to which garden, it is recommended to label the docking stations with the garden number and description when storing them for winter.
Without separate docking station: It is possible to connect the lawn area by placing the perimeter wire between the two lawn areas parallel to each other as close as possible (see figure K, top left). The additional lawn area without docking station is not recorded in the map memory and the mower will not use the LogiCut cutting strategy in this lawn area without the docking station. The maximum recommended lawn area without a docking station is 50 m². The mower will mow until it runs out of battery and will need to be carried back to the docking station for charging.

Mowing

• Do not let children ride the mower.
• Press the stop button on top of the mower before lifting. Always lift the mower by its handle. (see figure F)

Make sure the cutting area is free of small animals such as hedgehogs or tortoises.
Only with Indego M 700: After successful installation you can either immediately begin to mow by confirming “Mow now” on the display, or wait for the next scheduled cutting period, as programmed by the “Bosch AUTO” Calendar Function (previous setting required).
A manual mowing schedule can also be set up according to your specific needs.
Only with Indego M+ 700: After successful installation, you can begin mowing immediately by confirming “Mow now” on the display, or on the free Bosch Smart Gardening App by pressing “mow”. You could also set up a programmed schedule, using the Bosch “SmartMowing” functionality, which can also plan future cutting sessions based on when it is forecasted to rain. You could also set up a programmed schedule in the calendar using the display or the Bosch Smart Gardening App.
The mower must mow a garden 3 times completely (do 3 full cuts) to learn the garden. During the learning phase, the visual result may not be optimal.
Approximate runtimes for complete garden coverage using LogiCut are listed below. Please note that the runtimes will vary depending on the lawn complexity and number of objects within the garden.

Set a schedule with frequent repetitions. This achieves good mowing results, the battery charge will last longer and you avoid debris on the lawn.
When the mower is mowing
In “manual” mode, the mower works until the lawn is mowed. Mowing is interrupted only for charging the battery. When the garden is mowed, the mower returns to the docking station.
In the programmable “Schedule” mode, with the “Bosch AUTO” calendar function or with the Bosch “SmartMowing” functionality, the mower operates continuously for a set period of time. Mowing is interrupted only for charging the battery. If the garden is mowed before the time period expires, the mower returns to the dock.
To stop mowing prematurely, press the Stop button or send the mower back to the docking station pressing the confirm button ✓.
With Indego M+ 700 you can send the mower back to the docking station, by pressing the “Dock” button on the free Bosch Smart Gardening App.
Energy saving mode
The mower reduces its energy consumption by automatically switching off the power in the perimeter wire when it is not mowing and not being charged.
To wake up the mower manually from the energy saving mode, press the confirm button ✓and afterwards select either “Mow now” or another “Mowing mode”, while the mower is in the docking station.
With Indego M+ 700 you can wake up the mower remotely from the energy saving mode, by pressing the “mow” button on the free Bosch Smart Gardening App.
For mowing based on an active schedule or with the “Bosch AUTO” calendar function or with the Bosch “SmartMowing” functionality, the energy saving mode is automatically ended.
Mowing small lawn areas with „SpotMow“
SpotMow is intended for mowing small areas that require special treatment without having to mow the whole lawn, such as the area under a piece of garden furniture that has been removed. The mower is positioned at the lower left corner of the intended area to mow (see figure H). The final mowed area depends on the lawn conditions; it will not necessarily be an exact square. After completion of „SpotMow“, follow the instructions on the screen.
Note: For safety reasons, „SpotMow“ cannot be used outside the perimeter wire.
Sensors
The mower is equipped with the following sensors:

• The lift-up sensor is activated when the mower is lifted.

• The rollover sensor detects when the mower tips over.

• The tilt sensor is activated when the mower reaches a slope angle of 32°.
  When one of the sensors is activated, e.g. the lift-up sensor, the drive motors and cutting blades are stopped. A message is indicated in the display, e.g. “lift-up”.

• The obstacle sensor detects objects/obstacles alongside the entire front edge of the mower and causes a change of direction.

Battery charging
The battery is equipped with temperature monitoring that allows charging only if the battery internal temperature is in the range between 5 °C and 45 °C.
The lithium-ion battery is supplied partially charged. It is recommended to charge the mower during installation of the perimeter wire in the docking station.
The lithium-ion battery can be charged at any time without reducing its service life. Interrupting the charging procedure does not damage the battery.
When the battery is run flat or discharged, the mower is shut off by means of a protective circuit: the blades no longer move.
Replacing the Battery (see figure L)
Note: The battery only needs to be replaced when it is exhausted. It is not intended to charge the battery outside the mower.

• Using unsuitable batteries can lead to malfunctions or damage the mower.
• Heavily used batteries may have a significant effect in the mower run time.
• Do not use non-rechargeable batteries in the mower.
  Use only batteries specified by the manufacturer.

Note: Always wear protective gloves when handling or working near the sharp blades.
Switch off the mower by the isolator switch.
Remove the 5 screws of the battery compartment cover with a Torx T-20 screwdriver.
Pivot the used battery with the guide rail out of the battery compartment until the battery unlocking button can be seen and accessed. Press the battery unlocking button and remove the battery.
Insert the new battery into the guide rail until the locking mechanism can be heard to engage. Pivot back the battery with the guide rail into the battery compartment. Mount the battery compartment cover and screw it tight with the 5 screws.
The battery compartment cover protects the battery against moisture during operation.
Updating the Software (see figure M)
To update the software, you need a USB.org stick (FAT 32 formatted) and a USB OTG cable.
If a new software version is available, you can find it on the Internet on the “ www.bosch-indego.com ” page. Load the “IN8xxxx.bin” file onto the USB.org stick.
Turn the mower over and remove the cover from the USB port. Connect the USB OTG cable with the USB.org stick.
Place the mower in the docking station and make sure that the docking station is connected to mains (LED on docking station is on). The mower must be switched on, the display alight and the battery must be at least 70% charged.
When the update starts, the following message appears in the display “Do you want to update from version x to version y?”
Confirm by pressing the confirm button ✓. During the update, both LEDs in the mower will flash.
At the end of the update, the mower restarts.
Remove the USB OTG cable and the USB.org stick. Close the cover of the USB port.
Additionally with Indego M+ 700: You can download the software via the Bosch Smart Gardening app.

Menu Navigation

The table below explains the various menu items.

“Off/Manual”, the mower works until the display shows “garden complete”.
In “Schedule” mode, with the “Bosch AUTO” calendar function or with the Bosch “SmartMowing” functionality, the mower will operate until the end of the time period or until the display shows
“garden complete” (whichever comes first).
Calendar| Only with Indego M 700:
Bosch AUTO| | The “Bosch AUTO” calendar function is optimised based on the size of the lawn area.
In the default setting, the mower does two full cuts a week and starts at 8 am.
The following settings are possible:
Number of complete mowing cycles per week| 1 to 3
Weekday| Days on which mowing is allowed (e.g. to exclude Sundays).
Start time| Only possible for the first time slot (applies to all active days).
Only with Indego M+ 700: SmartMowing| | The Bosch “SmartMowing” function is optimised based on the size of the lawn area and gives additional functionality to connect to a local weather data provider.
In the default setting, the mower does two full cuts a week and starts at 8 am.  You can set up your SmartMowing schedule by using the free Bosch Smart Gardening App.
Schedule| Edit (selected day)| Program a mowing schedule by setting individual mowing days and slots (up to 2 per day).
Don’t mow/Delete slot| This will delete the corresponding slot for the selected day.
The number of full cuts per week for the actual schedule are shown at the bottom of the display.
Off/Manual| | Choose this option when no schedule should be used. The mower starts mowing only by activating “Mow now”.
With Indego M+ 700 you can start mowing, by pressing the “mow” button on the free Bosch Smart Gardening App.
Settings| Mowing mode| SpotMow| Select between a size of 2 m x 2 m, 3 m x 3 m and 4 m x 4 m.
Mow without docking station| Mower will mow in the additional lawn area without docking station in random mode until it runs out of battery.
Border cut| Select between the mower cutting the border once every full cut (default setting), once every two full cuts, or not performing a border cut (off).
Security| Auto Lock| If buttons are not pressed for 3 min. they will be automatically locked.
Recommended for safety reasons and protection against theft.
– On| PIN code is required for reactivation after Auto Lock.
– Off| The buttons are always ready for input.
Change PIN| Changing of a PIN code requires entering of existing PIN code first.
Alarm|
– On| Alarm is activated.
– Off| Alarm is deactivated.
Date & Time| | Change the date and time.
Set Language| | Change the display language.
Info| System status| Information on battery charge, system information and operating and charging time for the mower.
Advanced| Wire ID| Change the perimeter wire ID when possible interferences are nearby.
Sensor setting/Lawn condition| Select between Low (uneven ground), Normal and High (slippery ground). Mower bump sensor will become more or less sensitive depending on lawn condition selected.
Remap| Deletes the current map of the garden.
Factory Reset| Reset the mower to factory settings will delete all personal settings (not PIN).
After a factory reset, the mower will need to remap the garden/s.
Garden Overview| Displays the number of mapped gardens, their size, their wire ID and the date of the last time the garden was cut.
Delete garden| Delete one specific garden map or select to delete all maps at once.
Name mower| Change the name shown in the display. Only letters of the Latin alphabet are possible. The number of letters is limited. This function is not available in every language.
In some languages (e.g. Czech or Polish) a name change doesn’t have any effect on display due to specific grammar requests.
Tools| Level check| Information about the ground angle of the mower. If the mower is in the docking station and the dot on the display is not within the indicated circle, the docking station must be mounted at a new, more level location.
Wire signal| Detects the wire signal received from the perimeter wire, indicating its strength (for Service
Agent).
The mower will not receive a wire signal while in the docking station.

Troubleshooting

Online Support

https://www.bosch-garden.com/gb/en/garden-tools/indego-home.jsp
http://www.bosch-indego.com

Check that the perimeter wire is not interrupted and is between 20 and 350 meters in length. Then switch power supply off and then on again.
Follow instructions in Installation Guide to install the mower.
Excessive vibrations/ noise| Blade bolt loose| Tighten blade bolt to torque of 2.5 Nm.
Cutting blade damaged/bent| Replace cutting blade (see figure J).
Mower not docking reliably| Perimeter wire not properly layed out around docking station| Follow instructions in Installation Guide on layout of perimeter wire.
Perimeter wire close to a source of interference| Remove any excess (e.g. coiled up) perimeter wire around the docking station.
Change perimeter wire ID in the menu.
Mower fails to operate| Isolator switch not turned on| Remove mower out of docking station, turn isolator switch on and place mower back into docking station (ensure docking station is on – LED lights up green).
Possible clogging| Always turn isolator switch off first, then check underneath the mower. Clear out as necessary (always wear protective gloves).
Battery not fully charged| Place mower in the docking station to allow to charge.
Docking station must be on.
Grass too long| Mow lawn with conventional lawnmower to its lowest height-of- cut setting before using the mower.
Battery too hot/cold| The mower operates when the battery internal battery temperature is between 5 °C – 45 °C. Allow mower to cool down/warm up. If the error occurs frequently, the docking station should be positioned in the shade.
Mower standing on lawn with the display
switched off| Operational problems| Press confirm button for screen to light up, or place mower in docking station.
Mower does not charge| Battery too hot/cold| The mower operates when the battery internal temperature is between 5 °C – 45 °C. Allow mower to cool down/ warm up. If the error occurs frequently, the docking station should be positioned in the shade.
Docking station not switched on| Switch on power supply to docking station. If docking station does not start, contact your Bosch Service Centre.
Charging pins corroded| Clean the charging pins.
Battery not fitted, incorrectly fitted or incorrect battery for mower| Insert battery correctly (see figure L). Use the appropriate Bosch battery.
Mower out of perimeter wire| Perimeter wire on a slope| Leave 30 cm between the perimeter wire and the slope.
Obstacle near perimeter wire| Remove obstacle.
Parts of the lawn area left uncut| Mower requires more cuts to finish garden| Allow mower to run for 3 full cuts to cover whole lawn area.
Time slot not long enough for garden size| Increase mowing time slot or:
– use “Bosch AUTO” calendar function (with Indego M 700)
– use Bosch “SmartMowing” functionality (with Indego M+ 700)
Distance between perimeter wires too
small| Increase distance between the perimeter wires to a minimum of 75 cm.
Rough mowing conditions| Select “uneven ground/low sensitivity” option from menu item “lawn condition/bump sensor”.
Flatten garden/remove/bumps/mark out unsuitable areas with the perimeter wire – Please follow the instructions in the Installation Guide.
Grass too long| Select “uneven ground/low sensitivity” option from menu item “lawn condition/bump sensor”.
Slopes in garden too steep| Ensure mower only operates on slopes of 15 degrees or less and full garden is not on a slope.
Mower gets stuck in garden| Objects/obstacles not marked out| Use the perimeter wire to mark off obstacles where the mower often gets stuck.
Newly laid turf| Allow a few weeks for the soil to settle before using the mower.
Change setting in menu item “lawn condition / bump sensor” to low sensitivity / uneven.  After watering, wait as long as possible until you start the mower.
Mower unintentionally cuts flowers, etc. or
runs over certain obstacles| Objects/obstacles below 5 cm not marked out| Mark obstacle using perimeter wire leaving 30 cm from object or remove objects/obstacles.
Mower does not appear to cut logically| LogiCut system depends on the garden conditions. Mower does not necessarily have to continue in the next uncut area.| Further information can be found on the Installation Guide.
If behaviour re-occurs often, remap garden.
Mower does not always go in a straight line when travelling between areas| No corrective action needed.
Mower frequently does not find right position or turns on the spot| Change wire ID.
Wire crossed while marking an object| Follow instructions in the Installation Guide.
Mower runs in random paths in an additional lawn without docking station.| Normal behaviour. The LogiCut system only works in areas with docking station.
Perimeter wire keeps being cut| Wire is not taut between pegs Distance between pegs is more than 75 cm| Make wire taut and ensure distance between pegs is maximum 75 cm. Follow instructions in the Installation Guide. Use the wire connectors to repair the cut.
Mower leaves ragged finish/poor quality of
cut| The mower does not mow often enough| Mow more frequently for a good result (e.g. by means of more/longer slots in schedule).
Cutting blades blunt| Reverse or replace cutting blades (see figure J).
Possible clogging| Always turn isolator switch off first, then check underneath the mower. Clear out as necessary (always wear protective gloves).
Perimeter wire not detected| No power at the docking station| Check if the docking station is powered up (LED is on).
Perimeter wire damaged/cut| Check perimeter wire for damage.
Wrong installation (e.g. not enough distance between wires)| Follow instructions in the Installation Guide.
Perimeter wire close to a source of interference| Remove any excess (e.g. coiled up) perimeter wire around the docking station. Change perimeter wire ID in the menu.
Height-of-cut button stuck| Possible clogging| Always turn isolator switch off first, then check underneath the mower. Clear out as necessary (always wear protective gloves).

After-sales Service and Application Service

www.bosch-garden.com
In all correspondence and spare parts orders, please always include the 10-digit article number given on the type plate of the mower.
It is possible, that the software version of your mower is required (see „Menu

Settings > Info“).
If the mower is requested to be sent to the service centre, the mower and docking station must always be sent together. Do not remove the battery.
Before sending in, remove any personalised top cover that may have been fitted and any accessory cover.

Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888

Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch-pt.com.au
www.bosch-pt.co.nz
Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-Mail: bsctools@icon.co.za
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: (031) 7012120
Fax: (031) 7012446
E-Mail: bsc.dur@za.bosch.com
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: (021) 5512577
Fax: (021) 5513223
E-Mail: bsc@zsd.co.za
Bosch Headquarters
Midrand, Gauteng
Tel.: (011) 6519600
Fax: (011) 6519880
E-Mail: rbsa-hq.pts@za.bosch.com

Transport
The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. The batteries are suitable for road-transport by the user without further restrictions.
When shipping by third parties (e.g.: by air transport or forwarding agency), special requirements on packaging and labelling must be observed. For preparation of the item being shipped, consulting an expert for hazardous material is required.
Dispatch battery packs only when the housing is undamaged. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging. Please also observe the possibility of more detailed national regulations.

Disposal
The garden product, batteries, accessories and packaging should be sorted for environmental-friendly recycling.
**** Do not dispose of garden products and batteries/rechargeable batteries into household waste!

Only for EC countries:
According to the European law 2012/19/EU, electrical and electronic equipments that are no longer usable, and according to the European law 2006/66/EC, defective or used battery packs/batteries, must be collected separately and disposed of in an environmentally correct manner. Contact your Bosch Service Centre for details.
Battery packs/batteries:
Li-Ion:
Please observe the instructions under Transport.

EU Declaration of Conformity
Robotic Lawnmower
Article number
We declare under our sole responsibility that the stated products comply with all applicable provisions of the directives and regulations listed below and are in conformity with the following standards.

Indego M 700| 3 600 HB0 2..| 2006/42/EC
2014/53/EU
2011/65/EU
2000/14/EC
EN 60335-1:2012+A11:2014+A13:2017
EN 50636-2-107:2015
EN 301 489-3 V2.1.1
EN 55014-1:2017
EN 55014-2:2015
EN 303 447 V1.1.1
EN 50581:2012
EN 62311:2008
---|---|---
Indego M+ 700| 3 600 HB0 3..| 2006/42/EC
2014/53/EU
2011/65/EU
2000/14/EC
EN 60335-1:2012+A11:2014+A13:2017
EN 50636-2-107:2015
EN 301 489-3 V2.1.1 §
EN 301 489-52 V1.1.0
EN 55014-1:2017
EN 55014-2:2015
EN 303 447 V1.1.1
EN 301 511 V12.5.1
EN 50581:2012
EN 62311:2008

2000/14/EC: Measured sound power level 61 dB(A), uncertainty K = 2 dB, guaranteed sound power level 63 dB(A)
Conformity assessment procedure in accordance with annex VI. Product category: 32
Notified body: DEKRA Certification B.V., Meander 1051, 6825 MJ Arnhem, Netherlands, Nr. 0344
2014/53/EU: EU type examination no. ATCB024848 by notified body no. 1588. , ACB, Inc., 6731 Whittier Avenue, Suite C110, Mc-Lean, Virginia 22101, United States
Technical file at: *

| * Robert Bosch Power Tools GmbH, PT/ECS, 70538 Stuttgart, GERMANY
---|---
Henk Becker Chairman of Executive Management| Helmut Heinzelmann
Head of Product Certification

Robert Bosch Power Tools GmbH, 70538 Stuttgart, GERMANY
Stuttgart, 15.04.2020
Robert Bosch Power Tools GmbH
70538 Stuttgart
GERMANY
www.bosch-pt.com
F 016 L81 041 (2020.04) O / 449

References

• Location selection | Bosch Power Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>