LASER WORLD Tarm Series Show Laser Light Instruction Manual
- June 4, 2024
- LASER WORLD
Table of Contents
Series Show Laser Light
Instruction Manual
Tarm Series Show Laser Light
term Series
Please spend a few minutes to read this manual fully before operating this
laser!
Legal notice:
Thank you for purchasing this term laser technologies tilt GmbH & Co.KG
product.
Due to continual product developments and technical improvements, Ray
Technologies GmbH reserves the right to make modifications to its products.
This manual and its content have been made with due care but neither
Laserworld (Switzer- land) AG nor its subsidiary term laser technologies tilt
GmbH & Co.KG cannot, however, take any responsibility for any errors,
omissions, or any resulting damages forthwith.
The brands and product names mentioned in this manual are trademarks or
registered trademarks of their respective owners.
Attention: This device is a show laser device for commercial use. This device
is not a laser pointer, is not suitable for printing purposes, and must not be
used as a laser pointer.
Security Label
Please read the manual before operation
Use in enclosed spaces only!
- Laser radiation! Avoid exposure to beam
- Laser class 4
- Caution of radiation if the cover is removed
- Model type
- Production year
- Output power
- Wavelength
- Power supply & consumption
Front Panel
A. Laser aperturfenster
B. Beam block
C. Emission led
Back Panel
1. DMX In
2. DMX Out
3. shown Display
4. Interlock
5. Interlock
6. LAN: Computer connection
7. LAN: Computer connection| 8. Power Out
9. Power In
10. Loop for a safety cord
11. Scan Safety System (SFS)
12. ILDA In
13. ILDA Out
14. Key switch
---|---
Back Panel
1. DMX In
2. DMX Out
3. shown Display
4. Interlock
5. Interlock
6. LAN: Computer connection
7. LAN: Computer connection| 8. Power Out
9. Power In
10. ILDA In
11. ILDA Out
12. Key switch
13. Loop for a safety cord
---|---
Find information on how to operate your laser here:
https://www.laserworld.com/en/online-manual
Product and package contents
Please check if all listed parts are included and undamaged. Included in
delivery:
The laser system, power cable, key, interlock bridge plug, manual, technical
datasheet
Preliminary warning notices
- Please use this device only according to these operating instructions.
- Do not use the device if there are any visible damages to housing, connector panels, power supplies or power cords.
- This device must not be permanently connected to the mains. Disconnect it from the mains or use the power button to switch if off if not in use.
- Never look directly into the light source of a laser projector. The danger of damage to the eyes or even blindness in extreme circumstances!
- Do not operate the device at high humidity or in the rain or in dusty environments.
- Protect the device from dripping or splashing water. Do not place any liquid-filled containers near to this device.
Any warranty claims are void if the warranty label is removed or tampered with in any way.
Initial operations, safety instructions
- Make sure to use the correct voltage; see information on device & in this manual.
- Make sure that the device is not connected to the mains during installation.
- The installation has to be done by technical experienced and qualified persons according to the safety regulations of the respective country.
- Always ensure that maximum permissible exposure (MPE) is not exceeded in areas accessible to the public or members of staff.
- In some countries, an additional inspection by technical control institutes could be necessary.
- Connect an easily accessible interlock connector or circuit breaker to the projector.
- The power supply should be easily accessible.
- When installing the laser mount it at a minimum distance of 15 cm from walls and objects.
- For safe setup e.g. on walls or ceilings please use a safety cord. The safety cord should be able to withstand tenfold the weight of the device. Please follow the accident prevention regulations of professional associations and/or comparable regulations for accident prevention.
- If the device has been exposed to great temperature changes, do not switch it on immediately. Condensation (or any moisture/water formed) may damage this device.
- Never use dimmer, RC or other electronically switched sockets. Whenever possible, do not use the laser projector together with large appliances (especially fog machines) on the same mains!
- Ensure sufficient ventilation and do not place the device on any warm or heat radating surface. Especially the ventilation openings must not be covered!
- Ensure that the device does not get overheated. Make sure that the device is not exposed to spotlights (especially moving heads). Heat of spotlights could overheat laser in a little while and leads to a degradation of performance.
- This unit is intended for indoor use only.
Working on the device
- This product has no user-serviceable parts inside and should only be maintained and serviced by a qualified engineer.
- Be sure that the mains plug is not connected to the power supply while installing the device.
- Take off all reflecting things like rings, watches, etc. before starting to work with or at the projector.
- Only use non-reflecting tools to work on the device.
- Wear protective clothing (like goggles, gloves etc.) according to laser power and wavelength of the laser.
Service notes
-
Moisture and heat can reduce the lifetime of the laser system dramatically and expires any warranty claim.
-
Quick on/off switching of this device will reduce the durability of the laser diode dramatically.
-
Avoid sharp knocks and shocks to this device and ensure sufficient protection during transportation. Look after your Laserworld product.
-
To increase the durability of your laser, protect the device against overheating:
– Always ensure sufficient ventilation.
– Do not face spotlights (especially moving heads) on the device.
– Check temperature after approx. 30 minutes with each new installation. If necessary install the projector at a place with different temperatures.
– Keep the device dry. Protect it from moisture, rain, and dampness.
– Switch off the device when it is not needed. Diodes are switched on and can wear out even if there is no visible laser output. -
Please ensure the fans and heatsinks are clear from dust and debris otherwise the risk of overheating may occur. If the unit or air inlets appear to be blocked, please contact a qualified service engineer to maintain and service the product.
-
Removal of the warranty label as well as damages to the device caused by improper handling, neglect of the safety instructions, and service notes will void the warranty.
General Operation
-
Power
Connect the power cord to the device and to the mains. Make sure that your device is provided with the correct voltage. The wrong voltage could lead to irreparable damage. Please find the correct voltage data in the synoptical table at the end of this manual. Make sure that the device is not directed at people or inflammable objects during installation. To start the device, connect the interlocking bridge, insert the key and switch it on, and switch the device on. The “Emission – Laser on” LED at the front side of the device begins to light up when the device is ready for use. -
Key Switch
There is a key switch at the back of the laser system. Please plug the key to the switch and turn it on. The laser device only runs when the key is inserted and switched on. Prevent misuse! Unplug the key when the laser is unattended to prevent misuse of the system. -
Fuse
There is a fuse at the back side of the device. If the fuse should blow, please exchange it with a new one. If the problems recurs, please contact your dealer or the Laserworld service department. -
Safety Presets
This device has an integrated Scan Safety (SFS). Is the Scan Safety active (on), single beams are prevented. If the Scan Safety is switched off, it is possible to create full-power single beams – be careful! Operating the laser system with disabled SFS may not be allowed in some countries. Always ensure that maximum permissible exposure (MPE) is not exceeded in areas accessible to the public or members of staff. -
X / Y Inversion
Use the X, and Y buttons to invert the beam’s resp. patterns on the x-axis and/or y-axis. -
Modes / Functions
The different operation modes can be selected by using the ShowNET-Display at the back of the device. Any change of the operation mode requires a restart of the device (switch the device off and on again or disconnect power and reconnect it again). Do not change any ShowNET-Display settings during operation. Random and dangerous laser output can occur. -
Operation Modes
This laser system can be operated in many different operation modes. Information, videos and tutorials are available online! -
Turn the device off
To turn off the device, turn the key to, OFF` and disconnect the power cable from the mains.
Final statement
term products are tested and the product packaging is inspected before leaving
our warehouse. Users must to follow the local safety regulations and warnings
within this manual and adhere to any regulations within its place of use.
Damages through inappropriate use will void any liability or warranty of our
products. Due to continual product developments, please check for the latest
update of this product manual at www.tarm.com. If you
do have any further questions, then please contact your dealer/place of
purchase or use our contact section on our website. For service issues, please
contact your dealer/place of purchase and ensure only genuine Laserworld spare
parts are used in any service repairs.
Errors and Omissions are excepted and products are subject to change.
tarm laser technologies tlt GmbH & Co.KG
Lindenallee 27
44625 Herne
Germany
Registered office: Herne / Germany
Company number: HRA 4462
CEO: Richard Krumhus UID: DE 22 87 70 68 6
WEEE-Reg.-No. (Germany): DE85045116
www.tarm.com
info@tarm.com
Find information on how to operate your laser here:
https://www.laserworld.com/en/online-manual
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>