makita DHP489 Cordless Hammer Driver Drill Instruction Manual
- October 30, 2023
- Makita
Table of Contents
makita DHP489 Cordless Hammer Driver Drill
Product Information
The DHP489 is a power tool that can be used for drilling and fastening. It has a high and low speed setting, and can be used with various materials such as masonry, steel, and wood. The tool has a maximum drilling capacity of 16mm (5/8 inches) for masonry, 13mm (1/2 inches) for steel, 38mm (1-1/2 inches) for auger bits, 51mm (2 inches) for self-feed bits and hole saws. The tool has a no-load speed of 0-1,800 /min and 0-550 /min for high and low speeds respectively. The blows per minute range from 0-27,000 /min for high speed and 0-8,250 /min for low speed. The overall length of the tool is 175mm (6-7/8 inches) and it weighs between 1.8-2.5 kg (4.0-5.5 lbs). The DHP489 operates on a DC 18V power supply and is compatible with several battery cartridges such as BL1815N, BL1820B, BL1830B, BL1840B, BL1850B, and BL1860B. It is also compatible with chargers such as DC18RC, DC18RD, DC18RE, DC18SD, DC18SE, DC18SF, DC18SH, and DC18WC.
Important Safety Information: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges and chargers may cause injury and/or fire. Always read the safety warnings, instructions, illustrations and specifications provided with this power tool before use.
Product Usage Instructions
- Ensure that the work area is clean, well-lit, and free of clutter to avoid accidents.
- Do not operate the power tool in explosive atmospheres or in the presence of flammable liquids, gases or dust.
- Keep children and bystanders away while operating the power tool to avoid distractions that may cause you to lose control.
- Ensure that the power tool plug matches the outlet and avoid modifying the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.
- Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators, to reduce the risk of electric shock.
- Do not expose the power tool to rain or wet conditions to avoid electric shock.
- Do not abuse the cord and keep it away from heat, oil, sharp edges or moving parts to avoid electric shock.
- Use an extension cord suitable for outdoor use if operating the power tool outdoors to reduce the risk of electric shock.
- Use a ground fault circuit interrupter (GFCI) protected supply if operating the power tool in a damp location is unavoidable to reduce the risk of electric shock.
- Contact the maker of your pacemaker or similar medical devices and/or doctor for advice before operating the power tool as it can produce electromagnetic fields (EMF) that are not harmful to most users but may interfere with certain medical devices.
SPECIFICATIONS
Model: | DHP489 |
---|---|
Drilling capacities | Masonry |
Steel | 13 mm (1/2″) |
Wood | Auger bit: 38 mm (1-1/2″) Self-feed bit: 51 mm (2”) Hole saw: 51 mm (2”) |
Fastening capacities | Wood screw |
Machine screw | M6 (1/4″) |
No load speed (RPM) | High (2) |
Low (1) | 0 – 550 /min |
Blows per minute | High (2) |
Low (1) | 0 – 8,250 /min |
Overall length | 175 mm (6-7/8″) |
Rated voltage | D.C. 18 V |
Net weight | 1.8 – 2.5 kg (4.0 – 5.5 lbs) |
- Due to our continuing program of research and development, the specifications herein are subject to change without notice.
- Specifications may differ from country to country.
- The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heaviest combinations, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge | BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B |
---|---|
Charger | DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF / DC18SH / DC18WC |
- Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
- WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges and chargers may cause injury and/or fire.
SAFETY WARNINGS
General power tool safety warnings
WARNING Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
- Work area safety
1. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
- Electrical safety
1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
2. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
5. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
6. If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.
7. Power tools can produce electromagnetic fields (EMF) that are not harmful to the user. However, users of pacemakers and other similar medical devices should contact the maker of their device and/or doctor for advice before operating this power tool.
- Personal safety
1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
2. Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
3. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
4. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
5. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
7. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
8. Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
9. Always wear protective goggles to protect your eyes from injury when using power tools. The goggles must comply with ANSI Z87.1 in the USA. It is an employer’s responsibility to enforce the use of appropriate safety protective equipment by the tool operators and by other persons in the immediate working area.
- Power tool use and care
1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
3. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
4. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
5. Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
7. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
8. Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
9. When using the tool, do not wear cloth work gloves which may be entangled. The entanglement of cloth work gloves in the moving parts may result in personal injury.
- Battery tool use and care
1. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
2. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
3. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
4. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
5. Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
6. Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130 °C may cause explosion.
7. Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
- Service
1. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
2. Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
3. Follow instruction for lubricating and changing accessories.
4. Do not modify or attempt to repair the appliance or the battery pack except as indicated in the instructions for use and care.
Cordless hammer driver drill safety warnings
-
Safety instructions for all operations
-
1. Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
2. Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory or fasteners may contact hidden wiring. Cutting accessory or fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
3. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations.
4. Hold the tool firmly.
5. Keep hands away from rotating parts. -
6. Do not leave the tool running. Operate the tool only when hand-held.
7. Do not touch the drill bit, the workpiece or chips immediately after operation; they may be extremely hot and could burn your skin.
8. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data.
9. If the drill bit cannot be loosened even youopen the jaws, use pliers to pull it out. In such a case, pulling out the drill bit by hand may result in injury by its sharp edge.
10. Make sure there are no electrical cables, water pipes, gas pipes etc. that could cause a hazard if damaged by use of the tool.
-
-
Safety instructions when using long drill bits
- 1. Never operate at higher speed than the maximum speed rating of the drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
2. Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
3. Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend causing breakage or loss of control, resulting in personal injury.
- 1. Never operate at higher speed than the maximum speed rating of the drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
WARNING: DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.
Symbols
The followings show the symbols which may be used for the equipment. Be
sure that you understand their meaning before use.
Important safety instructions for battery cartridge
- Before using battery cartridge, read all instruc-tions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
- Do not disassemble or tamper with the battery cartridge. It may result in a fire, excessive heat, or explosion.
- If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.
- If electrolyte gets into your eyes, rinse them out with clear water and seek medical atten-tion right away. It may result in loss of your eyesight.
- Do not short the battery cartridge:
- Do not touch the terminals with any con-ductive material.
- Avoid storing battery cartridge in a con-tainer with other metal objects such as nails, coins, etc.
- Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown.
- Do not store and use the tool and battery car-tridge in locations where the temperature may reach or exceed 50 °C (122 °F).
- Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.
- Do not nail, cut, crush, throw, drop the battery cartridge, or hit against a hard object to the battery cartridge. Such conduct may result in a fire, excessive heat, or explosion.
- Do not use a damaged battery.
- The contained lithium-ion batteries are subject to the Dangerous Goods Legislation require-ments. For commercial transports e.g. by third parties, forwarding agents, special requirement on pack-aging and labeling must be observed. For preparation of the item being shipped, consult-ing an expert for hazardous material is required. Please also observe possibly more detailed national regulations. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging.
- When disposing the battery cartridge, remove it from the tool and dispose of it in a safe place. Follow your local regulations relating to disposal of battery.
- Use the batteries only with the products specified by Makita. Installing the batteries to non-compliant products may result in a fire, exces-sive heat, explosion, or leak of electrolyte.
- If the tool is not used for a long period of time, the battery must be removed from the tool.
- During and after use, the battery cartridge may take on heat which can cause burns or low temperature burns. Pay attention to the han-dling of hot battery cartridges.
- Do not touch the terminal of the tool imme-diately after use as it may get hot enough to cause burns.
- Do not allow chips, dust, or soil stuck into the terminals, holes, and grooves of the battery cartridge. It may cause heating, catching fire, burst and malfunction of the tool or battery car-tridge, resulting in burns or personal injury.
- Unless the tool supports the use near high-voltage electrical power lines, do not use the battery cartridge near high-voltage electri-cal power lines. It may result in a malfunction or breakdown of the tool or battery cartridge.
- Keep the battery away from children.
CAUTION: Only use genuine Makita batteries. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger.
Tips for maintaining maximum battery life
- Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power.
- Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
- Charge the battery cartridge with room tempera-ture at 10 °C – 40 °C (50 °F – 104 °F). Let a hot battery cartridge cool down before charging it.
- When not using the battery cartridge, remove it from the tool or the charger.
- Charge the battery cartridge if you do not use it for a long period (more than six months).
FUNCTIONAL DESCRIPTION
CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool.
Installing or removing battery cartridge
- CAUTION: Always switch off the tool before installing or removing of the battery cartridge.
- CAUTION: Hold the tool and the battery car-tridge firmly when installing or removing battery cartridge. Failure to hold the tool and the battery cartridge firmly may cause them to slip off your hands and result in damage to the tool and battery cartridge and a personal injury.
To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge. To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator as shown in the figure, it is not locked completely.
CAUTION: Always install the battery cartridge fully until the red
indicator cannot be seen. If not, it may accidentally fall out of the tool,
causing injury to you or someone around you.
CAUTION: Do not install the battery cartridge forcibly. If the cartridge
does not slide in easily, it is not being inserted correctly.
Indicating the remaining battery capacity
Only for battery cartridges with the indicator
Press the check button on the battery cartridge to indi-cate the remaining battery capacity. The indicator lamps light up for a few seconds.
- NOTE: Depending on the conditions of use and the ambient temperature, the indication may differ slightly from the actual capacity.
- NOTE: The first (far left) indicator lamp will blink when the battery protection system works.
Tool / battery protection system
The tool is equipped with a tool/battery protection system. This system
automatically cuts off the power to extend tool and bat-tery life. The tool
will automatically stop during operation if the tool or battery is placed
under one of the following conditions:
-
Overload protection
This protection works when the tool/battery is operated in a manner that causes it to draw an abnormally high current. In this situation, turn the tool off and stop the application that caused the tool to become overloaded. Then turn the tool on to restart. -
Overheat protection
This protection works when the tool or battery is overheated. In this situation, let the tool and battery cool before turning the tool on again. -
Overdischarge protection
This protection works when the remaining battery capacity gets low. In this situation, remove the battery from the tool and charge the battery. -
Protections against other causes
Protection system is also designed for other causes that could damage the tool and allows the tool to stop automatically. Take all the following steps to clear the causes, when the tool has been brought to a temporary halt or stop in operation.
1. Turn the tool off, and then turn it on again to restart.
2. Charge the battery(ies) or replace it/them with recharged battery(ies).
3. Let the tool and battery(ies) cool down.
If no improvement can be found by restoring protection system, then contact your local Makita Service Center.
Switch action
CAUTION: Before installing the battery car-tridge into the tool, always
check to see that the switch trigger actuates properly and returns to the
“OFF” position when released.
To start the tool, simply pull the switch trigger. Tool speed is increased by
increasing pressure on the switch trigger. Release the switch trigger to stop.
NOTE: The tool automatically stops if you keep pull-ing the switch
trigger for about 6 minutes.
Electric brake
This tool is equipped with an electric brake. If the tool consistently
fails to quickly stop after the switch trigger is released, have the tool
serviced at a Makita service center.
Lighting up the front lamp
CAUTION: Do not look in the light or see the source of light directly.
Pull the switch trigger to light up the lamp. The lamp keeps on lighting while the switch trigger is being pulled. The lamp goes out approximately 10 seconds after releasing the switch trigger.
NOTE: When the tool is overheated, the tool stops automatically and the
lamp starts flashing. In this case, release the switch trigger. The lamp turns
off in one minute.
NOTE: Use a dry cloth to wipe the dirt off the lens of the lamp. Be
careful not to scratch the lens of lamp, or it may lower the illumination.
Reversing switch lever action
- CAUTION: Always check the direction of rotation before operation.
- CAUTION: Use the reversing switch lever only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool.
- CAUTION: When not operating the tool, always set the reversing switch lever to the neutral position.
This tool has a reversing switch lever to change the direction of rotation.
Depress the reversing switch lever from the A side for clockwise rotation or
from the B side for counterclockwise rotation.
When the reversing switch lever is in the neutral posi-tion, the switch
trigger cannot be pulled.
Speed change
- CAUTION: Always set the speed change lever fully to the correct position. If you operate the tool with the speed change lever positioned halfway between the “1” side and “2” side, the tool may be damaged.
- CAUTION: Do not use the speed change lever while the tool is running. The tool may be damaged.
Displayed Number| Speed| Torque| Applicable operation
---|---|---|---
1| Low| High| Heavy load- ing operation
2| High| Low| Light loading operation
To change the speed, switch off the tool first. Push the speed change lever to
display “2” for high speed or “1” for low speed. Be sure that the speed change
lever is set to the correct position before operation.
If the tool speed is coming down extremely during the operation with display
“2”, push the lever to display “1” and restart the operation.
Adjusting ring
You can select the action mode and adjust the fastening torque with the
adjusting ring.
- Selecting the action mode
- Adjusting the fastening torque
This tool has three action modes. Select the mode suitable for your work. Turn the adjust-ing ring and align the mark that you select with the arrow on the tool body.
- NOTICE: Always set the ring correctly to your desired mode mark. If you operate the tool with the ring positioned halfway between the mode marks, the tool may be damaged.
- NOTICE: Do not change the action mode while tool is rotating.
- NOTICE: If it is difficult to slide the adjusting ring, switch on and run the tool for a second, then stop the tool and slide the adjusting ring to your desired position again.
The fastening torque can be adjusted in 21 levels by turning the adjusting ring. Align the graduations with the arrow on the tool body. You can get the minimum fastening torque at 1 and maximum torque at 21. Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which torque level is required for a particular application.
Graduation| 1| 2| 3| 4| 5| 6| 7|
8| 9| 10| 11| 12| 13| 14| 15| 16|
17| 18| 19| 20| 21
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
Machine screw| M4| M5| M6
Wood screw| Soft wood (e.g. pine)| –| ø 3.5 x 22| ø4.1x 38| –
Hard wood (e.g.lauan)| –| ø 3.5 x 22| ø4.1x 38| –
NOTE: The adjusting ring does not lock when the arrow is positioned only halfway between the graduations.
ASSEMBLY
CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool.
Installing or removing driver bit/drill bit
Turn the sleeve counterclockwise to open the chuck jaws. Place the driver
bit/drill bit in the chuck as far as it will go. Turn the sleeve clockwise to
close the chuck. To remove the driver bit/drill bit, turn the sleeve
counterclockwise.
Installing side grip (auxiliary handle)
When operating in the heavier load, using the side grip enables to hold the
tool more stably. Install the side grip so that the protrusions on the arm fit
in the grooves on the tool barrel. Turn the grip clockwise to secure it.
Depending the operations, you can install the side grip either right or left
side of the tool.
Adjustable depth rod
The adjustable depth rod is used to drill holes of uniform depth. Loosen
the clamp screw, set the depth rod to desired position, then tighten the clamp
screw.
Installing hook
- WARNING: Use the hanging/mounting parts for their intended purposes only, e.g., hanging the tool on a tool belt between jobs or work intervals.
- WARNING: Be careful not to overload the hook as too much force or irregular overburden may cause damages to the tool resulting in per-sonal injury.
- CAUTION: When installing the hook, always secure it with the screw firmly. If not, the hook may come off from the tool and result in the personal injury.
- CAUTION: Make sure to hang the tool securely before releasing your hold. Insufficient or unbalanced hooking may cause falling off and you may be injured.
The hook is convenient for temporarily hanging the tool. This can be installed on either side of the tool. To install the hook, insert it into a groove in the tool housing on either side and then secure it with a screw. To remove, loosen the screw and then take it out.
Using hole
WARNING: Never use the hanging hole for unintended purpose, for
instance, tethering the tool at high location. Bearing stress in a heavily
loaded hole may cause damages to the hole, result-ing in injuries to you or
people around or below you.
- Use the hanging hole at the bottom rear of the tool to hang the tool on a wall using a hanging cord or similar strings.
Installing driver bit holder
Fit the driver bit holder into the protrusion at the tool foot on either
right or left side and secure it with a screw. When not using the driver bit,
keep it in the driver bit holders. Driver bits 45 mm-long (1-3/4″) can be kept
there.
OPERATION
CAUTION: When the speed comes down extremely, reduce the load or stop the
tool to avoid the tool damage.
Hold the tool firmly with one hand on the grip and the other hand on the
bottom of the battery cartridge to control the twisting action.
NOTICE: Do not cover vents, or it may cause over-heating and damage to
the tool.
Screwdriving operation
- CAUTION: Adjust the adjusting ring to the proper torque level for your work.
- CAUTION: Make sure that the driver bit is inserted straight in the screw head, or the screw and/or driver bit may be damaged.
First, turn the adjusting ring so that the arrow on the tool body points to the proper fastening torque level (1 – 21). Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed gradually. Release the switch trigger as soon as the clutch cuts in.
NOTE: When driving wood screw, pre-drill a pilot hole 2/3 the diameter of the screw. It makes driving easier and prevents splitting of the workpiece.
Hammer drilling operation
CAUTION: There is a tremendous and sudden twisting force exerted on the
tool/drill bit at the time of hole breakthrough when the hole becomes clogged
with chips and particles, or when striking reinforcing rods embedded in the
concrete.
First, turn the adjusting ring so that the arrow on the tool body points to the marking. Be sure to use a tungsten-carbide-tipped drill bit. Position the drill bit at the desired location for the hole, then pull the switch trigger. Do not force the tool. Light pressure gives best results. Keep the tool in position and prevent it from slipping away from the hole. Do not apply more pressure when the hole becomes clogged with chips or particles. Instead, run the tool at an idle, then remove the drill bit partially from the hole. By repeating this several times, the hole will be cleaned out and normal drilling may be resumed.
Blow-out bulb
After drilling the hole, use the blow-out bulb to clean the dust out of the
hole.
Drilling operation
- CAUTION: Pressing excessively on the tool will not speed up the drilling. In fact, this excessive pressure will only serve to damage the tip of your drill bit, decrease the tool performance and shorten the service life of the tool.
- CAUTION: Hold the tool firmly and exert care when the drill bit begins to break through the workpiece. There is a tremendous force exerted on the tool/drill bit at the time of hole break through.
- CAUTION: A stuck drill bit can be removed simply by setting the reversing switch to reverse rotation in order to back out. However, the tool may back out abruptly if you do not hold it firmly.
- CAUTION: Always secure workpieces in a vise or similar hold-down device.
- CAUTION: If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery.
First, turn the adjusting ring so that the arrow points to the marking. Then proceed as follows.
Drilling in wood
When drilling in wood, the best results are obtained with wood drills equipped
with a guide screw. The guide screw makes drilling easier by pulling the drill
bit into the workpiece.
Drilling in metal
To prevent the drill bit from slipping when starting a hole, make an
indentation with a center punch and hammer at the point to be drilled. Place
the point of the drill bit in the indentation and start drilling. Use a
cutting lubricant when drilling metals. The excep-tions are iron and brass
which should be drilled dry.
MAINTENANCE
- CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance.
- NOTICE: Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.
- To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION: These accessories or attachments are recommended for use with
your Makita tool specified in this manual. The use of any other accessories or
attachments might present a risk of injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
- Drill bits
- Driver bits
- Driver bit holder
- Blow-out bulb
- Hook
- Side grip
- Depth rod
- Rubber pad assembly
- Wool bonnet
- Foam polishing pad
- Makita genuine battery and charger
NOTE: Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.
MAKITA LIMITED WARRANTY
Please refer to the annexed warranty sheet for the most current warranty terms
applicable to this product. If annexed warranty sheet is not available, refer
to the warranty details set forth at below website for your respective
country.
United States of America:
www.makitatools.com
Canada: www.makita.ca
Other countries: www.makita.com
WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
- lead from lead-based paints,
- crystalline silica from bricks and cement and other masonry products, and
- arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi 446-8502 Japan
www.makita.com
References
- Makita Canada | The Leader In Power tool Technology
- MAKITA Industrial Power Tools - The Leader In Cordless with 18V LXT Lithium-Ion
- Makita U.S.A | Cordless and Corded Power Tools, Power Equipment, Pneumatics, Accessories
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>