Royal Gourmet SG6002 Classic 6 Burner Propane Gas Grill with Side Burner Installation Guide

Royal Gourmet SG6002 Classic 6 Burner Propane Gas Grill with Side Burner

Installation Guide

FOR YOUR SAFETY!

Use outdoors only! Do not use it inside a building, garage, or any other enclosed space. Read the instructions before assembling and using the appliance.
DO NOT use the grill unless it is completely assembled, and all the parts are securely fastened.
This grill will become very hot, do not move it during use. Keep away from children and pets.

CONTACT US FIRST!

This grill has been made to high quality standards.
If you have any questions that are not addressed in this Owner’s Manual, or you need parts, please call our customer service hotline or send an email to [email protected] Please keep this Owner’s Manual for future reference

Parts Diagram

Parts and Hardware List

Preparation

Before beginning assembly, make sure all parts are present. Compare parts with packaged contents list and diagram above. If any parts are missing or damaged, do not attempt to assemble the products. Contact
customer service for replacement parts via telephone or email.

• Estimated assembly time: 40 minutes
• Tools required for assembly:, Phillips Screwdriver (not included) and Wrench (not included)
• Note: The right and left sides of the grill are designed as if you are facing the front of the grill.

CALIFORNIA PROPOSITION 65 WARNING

1.  Fuels used in gas burning appliances and the combustion byproducts of such fuels, can expose you to chemicals including carbon monoxide, which is known to the State of California to cause birth defects or\ other reproductive harm.
2. This product can expose you to chemicals including nickel, which is known to the State of California to cause cancer. Handling the brass material on this product can expose you to lead, a chemical known to the State of California to cause cancer, birth defects, or other reproductive harm.
   For more information visit: www.P65Warnings.ca.gov

Assembly Instructions

Assemble the casters (1) to the side panels (2), (3) by twisting clockwise until tightened.

Step 2

Assemble the side panels to the bottom shelf (4) with 8 bolts (A) as shown.

Assemble the rear panel (6) by attaching it to the side panels and the bottom shelf, then secure it with 5 bolts (8).

Fasten one end of the LP tank barrier bar (5) to the right panel (2) as shown, and secure the other end to the bottom shelf (4) with 2 bolts (8).

Assembly Instructions

Assemble the cart front beam (7) to the side panels with 4 bolts (A).
Fasten the magnet (E) to the bottom shelf with 2 bolts (C) as shown.

Insert the sleeves (D) into holes at the bottom shelf as shown.

Assemble the door handles (10) and door sleeves (11) to the doors (8), (9) with 4 bolts (F).

Install the doors to the cart by inserting one end of the door axles (12) into the holes on the cart\ front beam, and the other end into the sleeves on the bottom shelf.

Assemble the thermal baffle (13) to the left side panel with 2 bolts (G).

Please note: Do not detach three straps here.

Remove the packaging film from the hose and the regulator under the control panel (cut by scissors). Place the main body (14) on the cart, and secure with 4 bolts (8).

Assemble the lid handle (15) to the lid with 2 bolts (F).

Assemble the side table decoration board (17) to the side table (16) with 3 bolts (B).

Assemble the side burner decoration board (19) to the side burner shelf (18) with 2 bolts (B).

Fasten the thermal baffle (13) to the cart front beam with 1 bolt (B).

Attach the parts assembled in step 13 to the four holes on the left side of the grill, and secure from inside of the main body with 4 washers (H) and 4 bolts (B).

Secure the parts from outside of the main body with another 5 bolts (B) under the shelf.

Attach the parts assembled in step 14 to the four holes on the right side of the grill, and secure it from the inside of the main body with 4 washers (H) and 4 bolts (B).

And secure the parts from outside of the main body with another 5 bolts (B) under the shelf.

Assemble the knob base (20) to the side burner decoration board with 2 bolts (C), then insert the knob (21 ).

1. Unscrew the igniter cap and the nut from the igniter by twisting anticloskwise.

2.  Insert the igniter into the hole from the back of the side burner decoration board. Fasten the igniter by twisting the nut clockwise from the front.

3. Insert the battery into the igniter and cover it by twisting the igniter cap clockwise.

4. Unscrew the side burner valve below the side burner shelf.

5. .lnsert the side burner (22) through the side burner shelf, and tighten it with 2 bolts (C) beneath the shelf.

6. Connect the side burner orifice with the valve.

7. .Place the side burner grate (23) above the burner.

Insert the ignition match into the electrode port as shown.

Slide in the grease tray (25) underneath the main body. Slide in the grease cup (24) underneath the grease tray as shown.

Place the flame tamer (26) into the firebox. Place the flame tamers (27) into the firebox by attaching the slots of them to the buckles in the firebox as shown.

Place the cooking grates (28), (29) into the grill body.

Attach the warming rack to the relative holes on the main body as shown.

Place the LP tank into the nesting hole located in the bottom shelf. Pass the regulator through the hole on the left panel and connect it to the LP tank valve by twisting anticlockwise.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>