sensear SP1R In Ear Solution Powered From Radio User Guide

sensear SP1R In Ear Solution Powered From Radio

Product Information

SP1R Hearing Protection Communication Headset

The SP1R is a state-of-the-art hearing protection communication headset that uses patented processing technology to provide situational awareness while being in full contact with all your communication devices. It also has an intrinsically safe variant that meets international standards for use in explosive gas environments. The headset draws power from the two-way radio and must be connected by the appropriate SRCK7xxx radio cable to utilize both the situational awareness and two-way radio communications. The SRCK7xxx part numbers vary depending on the radio connector and are sold separately.

Product Earplug Fitting Instructions

1. Place disposable foam tip between thumb and forefinger.
2. Roll foam tip to a compressed, crease-free cylinder.
3. Push the foam tip all the way onto the earbud spout.
4. Roll the foam tip again between the thumb and forefinger.
5. Ensure the foam tip remains a compressed, crease-free cylinder on the earbud.
6. Using your opposite hand, pull your ear upward and outward. Insert the earbud deeply into the ear.
7. Hold the earbud in place for 30 seconds while the foam tip expands.
8. Check to ensure the earbuds are correctly inserted. A poor fit will be visible by the earbuds being far away from the ear. No part of the foam tip should be visible. Repeat the process until a good fit is achieved.

Power On/Off Instructions

• To power on, connect the SRCK7xxx radio cable to the Hirose connector on the bottom of the main unit. Connect the SRCK7xxx cable to the two-way radio. Turn the two-way radio on, and the headset will power up.
• To power off, turn the two-way radio off. Disconnect the headset cable from the SRCK7xxx cable (audio reverts to the two-way radio automatically).

Communicating Instructions

• Two-Way Radio VOX: VOX can be used on VOX-enabled two-way radios when using the SP1R Boom Mic headset option. Refer to the two-way radio documentation for the setup and use of the VOX feature. To enable VOX on the SP1R, press the SP1R’s PTT before putting the two-way radio into VOX mode. To disable VOX, you can either turn VOX off on two-way radio or press the SP1R’s PTT once, depending on which two-way radio model you use.

Product Environmental Modes

Your SP1R features situational awareness technology (Speech Enhancement, Noise Suppression) that allows you to be in audible contact with your surroundings while wearing your headset. The mode can be turned on and off by turning the volume knob to the on/off position with a click, which will toggle the unit into Quiet mode or Environmental mode, while also controlling the volume level.

Overview

POWER ON HEADSET

• Power On: Connect the SRCK7xxx radio cable to the Hirose connector on the bottom of the main unit. Connect the SRCK7xxx cable to the two-way radio. Turn the two-way radio on, and the headset will power up.
• Power Off: Turn the two-way radio off. Disconnect the headset cable from the SRCK7xxx cable (audio reverts to the two-way radio automatically).

COMMUNICATING

To Transmit Over Two-Way Radio:

• Press and hold the built-in PTT button located on the SP1R
• Release the inline PTT button to cease transmission

Two-Way Radio VOX: VOX can be used on VOX-enabled two-way radios when using the SP1R Boom Mic headset option. Refer to the two-way radio documentation for the setup and use of the VOX feature. To enable VOX on the SP1R, press the SP1R’s PTT before putting the two-way radio into VOX mode. To disable VOX, you can either turn VOX off on two-way radio or press the SP1R’s PTT once, depending on which two-way radio model you use.

ENVIRONMENTAL MODES

• Your SP1R features situational awareness technology. (Speech Enhancement, Noise Suppression)
• allows you to be in audible contact with your surroundings while wearing your headset.
• mode can be turned on and off by turning the volume knob to the on/off position with a click, which will toggle the unit into mode or quiet mode, while also controlling the volume level.

WEARING THE HEADSET

The SP1R is a state-of-the-art hearing protection communication system that allows you to retain 360° situational awareness with our patented processing technology while being in full contact with all your communication devices. There is an intrinsically safe variant of the product that meets international standards for use in explosive gas environments. The headset draws power from the two-way radio. It must be connected by the appropriate SRCK7xxx radio cable to utilize both the situational awareness and two-way radio communications. SRCK7xxx part numbers vary depending on the radio connector and are sold separately. For language translated manuals and further information, please refer to the website.

FITTING THE EARPLUGS

1. Place disposable foam tip between thumb and forefinger.
2. Roll foam tip to a compressed, crease free cylinder.
3. Push the foam tip all the way onto the ear bud spout.
4. Roll the foam tip again between the thumb and forefinger.
5. Ensure the foam tip remains a compressed, crease free cylinder on the ear bud.
6. Using your opposite hand, pull your ear upward and outward. Insert the ear bud deeply into the ear.
7. Hold the ear bud in place for 30 seconds while the foam tip expands.
8. Check to ensure the ear buds are correctly inserted.
9. A poor fit will be visible by the ear buds being far away from the ear. No part of the foam tip should be visible. Repeat the process until a good fit is achieved.

FOR COMPLETE MANUAL GO TO WEB: www.sensear.com/support/product- manuals

References

• Product Manuals | Sensear

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>