makita FS2200 Drywall Screwdriver Instruction Manual
- October 30, 2023
- Makita
Table of Contents
Drywall Screwdriver FS2200 FS2300 FS2300X
FS2200 Drywall Screwdriver
(Original instructions)
Explanation of general view
1-1. Lock ring
2-1. Locking sleeve
3-1. Locator
4-1. Locator
5-1. Switch trigger
5-2. Lock button
6-1. Lamp
7-1. Reversing switch lever| 8-1. Hook
9-1. Lock ring
9-2. Gear housing
10-1. Locator
10-2. Bit
10-3. Gear housing
11-1. Locator| 11-2. Locking sleeve
12-1. Locator
12-2. Bit
12-3. Magnetic bit holder
13-1. Swells
13-2. Trapezoidal holes
13-3. Locator holder
---|---|---
SPECIFICATIONS
Model | FS2200 | FS2300 | FS2300X |
---|---|---|---|
Capacities | Self drilling screw | 6 mm | 6 mm |
Drywall screw | 5 mm | 5 mm | 5 mm |
No load speed (min-1) | 0 – 2,500 | 0 – 2,500 | 0 – 2,500 |
Overall length | 287 mm | 290 mm | 305 mm |
Net weight | 1.6 kg | 1.6 kg | 1.6 kg |
Safety class | /II |
- Due to our continuing program of research and development, the specifications herein are subject to change without notice.
- Note: Specifications may differ from country to country.
- Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for screw driving in wood, metal and plastic.
ENF002-2
Power supply
The tool should be connected only to a power supply of the same voltage as
indicated on the nameplate, and can only be operated on single-phase AC
supply. They are double-insulated and can, therefore, also be used from
sockets without earth wire.
ENG905-1
Noise
The typical A-weighted noise level determined according to EN60745:
Model FS2300,FS2300X
Sound pressure level (LpA) : 83 dB (A)
Sound power level (LWA) : 94 dB (A)
Uncertainty (K) : 3 dB (A)
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) determined according to
EN60745:
Model FS2300,FS2300X Work mode: screwdriving without impact Vibration
emission (ah) : 2.5 m/s 2 or less Uncertainty (K) : 1.5 m/s
-
The declared vibration emission value has been measured in accordance with the standard test method and may be used for comparing one tool with another.
-
The declared vibration emission value may also be used in a preliminary assessment of exposure.
WARNING: -
The vibration emission during actual use of the power tool can differ from the declared emission value depending on the ways in which the tool is used.
-
Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible manufacturer declare that the
following Makita machine(s):
Designation of Machine:
Drywall Screwdriver
Model No./ Type: FS2300, FS2300X are of series production and
Conforms to the following European Directives: 2006/42/EC
And are manufactured in accordance with the following standards or
standardised documents:
EN60745
The technical documentation is kept by:
Makita International Europe Ltd.
Technical Department,
Michigan Drive, Tongwell,
Milton Keynes, Bucks MK15 8JD, England 19.6.2013
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502, JAPAN
General Power Tool Safety Warnings
WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
SCREWDRIVER SAFETY
WARNINGS
- Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring or its own cord. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
- Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations.
- Hold the tool firmly.
- Keep hands away from rotating parts.
- Do not touch the bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product (gained from repeated use)
replace strict adherence to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruction manual may cause
serious personal injury.
FUNCTIONAL DESCRIPTION
CAUTION:
- Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool.
Depth adjustment
For model FS2200, FS2300
Fig.1
The depth can be adjusted by turning the lock ring. Turn it in “B” direction
for less depth and in “A” direction for more depth. One full turn of the lock
ring equals 2.0 mm change in depth.
For model FS2300X
Fig.2
The depth can be adjusted by turning the locking sleeve.
Turn it in “A” direction for less depth and in “B” direction for more depth.
One full turn of the locking sleeve equals 1.5 mm change in depth.
For all Models
Adjust the lock ring so that the distance between the tip of the locator and
the screw head is approximately 1 mm as shown in the figures. Drive a trial
screw into your material or a piece of duplicate material. If the depth is
still not suitable for the screw, continue adjusting until you obtain the
proper depth setting.
Fig.3
Fig.4
Switch action
Fig.5
CAUTION:
- Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released.
To start the tool, simply pull the switch trigger. Tool speed is increased by
increasing pressure on the switch trigger. Release the switch trigger to stop.
For continuous operation, pull the switch trigger and then push in the lock
button.
To stop the tool from the locked position, pull the switch trigger fully, then
release it.
NOTE:
- Even with the switch on and motor running, the bit will not rotate until you fit the point of the bit in the screw head and apply forward pressure to engage the clutch.
Lighting up the lamps Fig.6
CAUTION:
- Do not look in the light or see the source of light directly. To turn on the lamp, pull the trigger. Release the trigger to turn it off.
NOTE:
- Use a dry cloth to wipe the dirt off the lens of lamp.
Be careful not to scratch the lens of lamp, or it may lower the illumination.
Reversing switch action
Fig.7
**CAUTION:**
- Always check the direction of rotation before operation.
- Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool.
This tool has a reversing switch to change the direction of rotation. Move the reversing switch lever to the position (A side) for clockwise rotation or the position (B side) for counterclockwise rotation. Hook Fig.8 The hook is convenient for temporarily hanging the tool.
ASSEMBLY
CAUTION:
- Always be sure that the tool is switched off and unplugged before carrying out any work on the tool.
Installing or removing the bit For model FS2200, FS2300
To remove the bit, first remove the locator by pulling the lock ring away from
the gear housing. Fig.9
Grasp the bit with a pair of pliers and pull the bit out of the magnetic bit
holder. Sometimes, it helps to wiggle the bit with the pliers as you pull.
To install the bit, push it firmly into the magnetic bit holder. Then install
the locator by pushing it firmly back onto the gear housing. Fig.10
For model FS2300X
To remove the bit, first pull the locator out of the locking sleeve. Then
grasp the bit with a pair of pliers and pull the bit out of the magnetic bit
holder. Sometimes, it helps to wiggle the bit with the pliers as you pull.
Fig.11
To install the bit, push it firmly into the magnetic bit holder. Then install
the locator by pushing it firmly back onto the locking sleeve.
Fig.12
Use of locator holder
Fig.13
The locator can be temporarily held on the locator holder during replacing bit
or using without locator. To hold the locator, position the trapezoidal holes
of the locator on the swells of the locator holder and push it in.
OPERATION
Fig.14
Fit the screw on the point of the bit and place the point of the screw on the
surface of the workpiece to be fastened. Apply pressure to the tool and start
it. Withdraw the tool as soon as the clutch cuts in. Then release the switch
trigger.
CAUTION:
- When fitting the screw onto the point of the bit, be careful not to push in on the screw. If the screw is pushed in, the clutch will engage and the screw will rotate suddenly. This could damage a workpiece or cause an injury.
- Make sure that the bit is inserted straight in the screw head, or the screw and/or bit may be damaged.
- Hold the tool only by the handle when performing an operation. Do not touch the metal part.
MAINTENANCE
CAUTION:
- Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance.
- Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
-
These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. -
Phillips Insert bits
-
Magnetic bit holder
-
Locator
NOTE:
- Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.
Makita Corporation
Anjo, Aichi, Japan
www.makita.com
Downloaded from www.Manualslib.com manuals
search engine
884912C988
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>