WFLY X9 FHSS Radio Transmitter Instruction Manual

WFLY X9 FHSS Radio Transmitter

Thank you for purchasing WFLY surface radio X9! WFLY X9 is a great radio set with a lot of exciting functions. We are confident that you will find lots of joy and fun with this radio system. Before you Shenzhen WFL Y Technology Development Co., Ltd
Address: C3 Buliding,Xiangli Industry Park,Heping Haoye Road,Fuyong Town,Baoan
District,Shenzhen,Guangdong Province,China.
Email:[email protected]
Website:www.wflysz.com

Turn on and off your radio

Power on

• Transmitter: Firstly press and hold the power button for 3 seconds to turn on your transmitter.
• Receiver: After the transmitter is powered on, then switch on your receiver Power off
• Receiver: Please switch off the receiver
• Transmitter: Press and hold the power button for 3 seconds to shut down.

Power supply range

Your radio is compatible with 3.5V-6V (exceeding the power supply voltage may cause damage to your radio)
Note: You can charge the radio if it is powered by a single lithium battery. DO NOT charge your radio if 4 AA dry batteries are inside the battery compartment.

After-sales policy

Should you have any question or doubt when you are driving this radio, please contact our sales staff. We would be glad to be of any assistance and support.
Email: [email protected]
Wechat: WFLY _RC
Facebook: Wfly RC
Face book group: WFLY RC Groups

Product parameters

• Radio parameters:
• Model Name: X9
• Channel: 9 channels
• Working voltage: 3.SV-6.0V
• Working current: 220mA
• Application: RC cars, boats, tanks, etc.
• Resolution: 4096
• Frequency band: 2.4GHz (two-way)
• Storage: 40 models memory
• Language: Chinese.English
• Upgrade: use online upgrade
• Display: 3.5″ 4B0*320 capacitive touch screen
• Voice: support voice broadcast
• Receiver parameters:
• Model name: RG2065
• Frequency band: 2.4GHz
• Working voltage: 3.SV-9.0V
• Working current: 95mA
• Application: RC cars, boats, tanks, etc.
• Resolution: 4096
• PWM: 6 channels
• PPM: support
• W.BUS: support 5.BUS
• Two way transmission: Support
• Upgrade: use online upgrade
• Dimension : 33.622.312.3mm

Names of radio parts

Receiver

Model speed unit Settings

Click the interface peak compass

Description of the home screen

1. Model name
2. Receiver signal strength
3. Condition mode
4. Transmitter battery
5. Timer(Default:P51)
6. Telemetry data: Receiver voltage
7. Telemetry data: External voltage
8. Telemetry data: Model speed
9. Steering trim(Default control: DTl)
10. Throttle trim (Default)
11. Dual rate (default control: DL)
12. Channel view
13. Menu
14. Lock screen button: long press for 2 seconds to lock/unlock the screen
15. User menu (default control: Ps2)

Link

Warning: When linking, please be careful not to connect the power equipment, and be careful that the sudden output of the engine may cause a shock hazard.
To ensure safety, please do not perform code matching operations when the motor and engine are running.

Path: [Menu]-[Linkage menu]-[Link]

Linking method:
Transmitter: Click the start button to enter the link state
Receiver: Power on, press and hold the [SET] button for 3 seconds, the orange LED flashes.

Authentication method:
Successful linking: The receiver LED light becomes green and steady
Connect the servo: Operate the corresponding channel of the transmitter, linking successfully if the servo has synchronized action.

Note:
The distance between the transmitter and the receiver shall be within one meter. The transmitter cannot be linked in simulator and student mode, mode modification
Path: [Menu]-[System Menu)-[Trainer and simulator)
There is no other WFLY 2.4G system in the vicinity that the same protocol is undergoing binding operation.
During the binding: If you need to exit, Touch [Cancel].

Receiver RGB LED status:

Failsafe

Importance of F/5 protection setting:
If you do not set the F/5 protection data, when the model loses control due to some reason, unexpected and uncontrollable actions may occur, causing the boat/car/tank to collide/fall, or even hurt humans. If you set the protection according to the parameters of the smooth driving in advance, then the chance of colliding, losing, or even hurting others after losing control will be much less.

Path: [Base setting)-[Fail safe)

Setting mode:

1. Hold: Hold mode, the value when the receiver output is out of control (hold action)
2. F/5: Loss of control protection mode, the set value output by the receiver after loss of control (default action). For safety, it is recommended to set this out of control protection mode, the throttle channel is set to brake action.
3. Close: Close the current channel output.
   Note: Model fail safe is very important. Failure to set it correctly can cause damage of your RC model, so you must be very careful when setting this function.

Warning

Low battery warning
When the transmitter voltage, receiver battery voltage and power battery voltage are lower than the set value (path: [Menu]-[System menu)-[Batteryl), the radio will broadcast corresponding voice reminders, such as [transmitter voltage is low, 3.SV],and you can set whether to turn on the vibration reminder as required.

Shutdown alarm interface:
After the telemetry function is enabled, the transmitter will check whether the receiver is communicating when it is off, and then the warning interface will pop up to confirm before shutdown.

Touch [Shutdown] to forcibly shut down the transmitter.

Model menu

Path: [Menu)-[Model Menu]

Switch and channel Settings

Path: [Menu)-[Advanced Menu)-[Channel setting)

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>