SZ Intelligent WiFi Strobe Smoker Detector User Manual
- October 30, 2023
- SZ
Table of Contents
SZ Intelligent WiFi Strobe Smoker Detector
Product Information
The device complies with part 15 of the FCC Rules and meets FCC radiation exposure limits. The device must not cause harmful interference and should accept any interference received, including interference that may cause undesired operation. Changes or modifications not approved by the party responsible for compliance may void the user’s authority to operate the equipment.
Product Usage Instructions
When using this device, ensure that it is installed and operated with a minimum distance of 20cm between the radiator and your body. Failure to do so may result in exceeding the FCC radiation exposure limits and could potentially cause harm. If you need to make any changes or modifications to the device, ensure that these are approved by the party responsible for compliance to avoid voiding your authority to operate the equipment.
This WiFi strobe smoke detector is a device that can detect smoke occurred at the beginning of a fire disaster and generates live strobe &sound alarms, at the same time, push alarm information to the mobile app by WiFi.
Technical Parameter
- Power supply: DC9V alkaline battery (6LR61)
- Static current: < 85uA
- Alarm current: <130mA
- Working temperature: -10°C~ +50°C
- Humidity: =95%RH, no freezing
- Alarm sound: >80dB
- Low battery alert: =6.5V+0.5V
Working Status
Mute & Testing
- Mute: in alarm status, press the ‘TEST’ button to mute the buzzer, only the LED indicator flashes.
- Testing: in normal status, long press the ‘TEST’ button for 2s to trigger the sound & light alarm, an alarm message is pushed to the mobile APP.
WiFi Configuration & Networking
WiFi configuration:
- Install the ‘Tuya Smart APP on your smartphone the first time you use the detector.
- Make sure your smartphone is connected to the WiFi.
- Launch the APP, and click ‘Add device’—‘ Security Sensor’—‘Sensor (WiFi).
- Long press the ‘TEST’ button for 5s until LED flashes with a short beep of ‘Di’.
- Click ‘OK’ in the APP—input the password for the WiFi and click ‘OK’, and the detector enters configuration mode which lasts for 60s maximum.
- Along beep of ‘Di’ with LED indicator on for 10s means the WiFi configuration is completed. When WiFi configuration fails, the detector exits configuration mode with a short beep of ‘Di Di Di’.
- WiFi configuration is done based on the 3 steps above.
WiFi Networking Status:
when the LED indicator is on for 10s after the battery is loaded, it means the
detector is successfully connected to WiFi.
Installation
Installing method
- Make a hole on the ceiling by using the percussion drill
- Install the expansion tube on the ceiling
- Fix the installation board by using the screw
- Aiming the alarming device with the installing board and connecting them, rotating clockwise till heard the “kaca” sound, means installing correctly.
Installing attention
- Indoor stalling only
- Keep 50cm between the device with the illumination lamp
- Keep away from the bathroom and watery place
- Keep away from the place with nonfire smoke and steam.
- Keep away the place below 0 C or above 50 C
- While the cupboard is near the ceiling, keep the device 60cm away from the cupboard.
- Keep the device 150cm away from the ventilator, air conditioner, and air vent.
- If the battery missed, the device cannot connect to installing board
Maintain
- Trouble happened while testing, please check immediately or send it back to the manufacturer.
- Battery life can be used for 1 year in the normal environment, age will be reduced in the high temperature and high humid environment.
- Please ensure all the functions be normal before installing, please keep them in a safe place and avoid dust, humidity, and corrosion.
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>