Sz Dji Technology RMYTBA01 RoboMaster Youth Tournament Base 01 User Guide
- June 5, 2024
- Sz Dji Technology
Table of Contents
Sz Dji Technology RMYTBA01 RoboMaster Youth Tournament Base 01
Disclaimer
Thank you for purchasing ROBOMASTERTM Youth Tournament Base 01 (hereinafter
referred to as “Base”). Please read this entire document and all safe and
lawful practices DJITM provided carefully before use. Failure to read and
follow instructions and warnings may result in serious injury to yourself or
others, damage to your DJI product, or damage to other objects in the
vicinity. By using this product, you hereby signify that you have read this
disclaimer and warning carefully and that you understand and agree to abide by
all terms and conditions of this document and all relevant documents of this
product. You agree to use this product only for purposes that are proper. You
agree that you are solely responsible for your own conduct while using this
product, and for any consequences thereof. DJI accepts no liability for
damage, injury or any legal responsibility incurred directly or indirectly
from the use of this product.
DJI is a trademark of SZ DJI TECHNOLOGY CO., LTD. (abbreviated as “DJI”) and
its affiliated companies. Names of products, brands, etc., appearing in this
document are trademarks or registered trademarks of their respective owner
companies. This product and document are copyrighted by DJI with all rights
reserved. No part of this product or document shall be reproduced in any form
without the prior written consent or authorization of DJI.
This document and all other collateral documents are subject to change at the
sole discretion of DJI. For up to date product information, visit
www.robomaster.com and click on the product page for this product.
Warning
- The use of any power adapter not provided officially by DJI may affect the lifespan of or cause permanent damage to the product, or result in current leakage causing personal injury. It is imperative to use an official power adapter provided by DJI.
- Make sure the Base is correctly connected to the power adapter before use.
- Avoid hitting or impacting the Base with force. Otherwise, the structure may be damaged and the circuit connections may be loosened.
- If you detect any flames, smoke, burning smells, or other abnormalities after the Base is powered up, disconnect the power supply immediately.
- Clean off any gel beads scattered on the Base’s structure regularly.
Introduction
The RoboMaster Youth Tournament Base 01 consists of an intelligent controller, camera, light indicator, and Electronic Visual Marker. Its structural surface has been treated with anodizing sandblasting. The Base carries functions such as hit detection, image display, lighting effects, and voice prompts. It can communicate various status information directly through a speaker, light indicator, or Electronic Visual Marker. The Base is suitable for use in areas such as robotic competition, interactive gaming, scientific research, and education.
In the Box
- Varies by region.
Overview
- Intelligent Controller
- Electronic Visual Marker
- Light Indicator
- Power Port
- Camera
Usage
Team Identity
After the Base is powered on, the light indicator of the Base and Electronic Visual Marker will display the default light color. The user can determine the Base’s default team identity by the light color. Users may change the default team identity of the Base by connecting to the competition’s engine. For specific ways to do so, please refer to the RoboMaster Champion User Guide. Users may access the document on the RoboMaster official website: https://www.robomaster.com/zh-CN/products/components/detail/3214.
Modules
Intelligent Controller
The intelligent controller can operate at a frequency of 2.4 GHz, 5.1 GHz or
5.8 GHz*. It can be used for tasks such as updating Base firmware, connecting
to supporting RoboMaster Champions and real-time transmission of data, and is
stable with low latency.
- 5.1 GHz only applies to indoor uses. Usage at 5.1GHz must comply with local regulations. Some regions do not allow outdoor uses at such a frequency.
CMIIT ID:2019AP12753
Electronic Visual Marker
The Electronic Visual Marker consists of an armor and LED dot-matrix displays.
A Hit Detector is installed inside each armor, which can detect attacks by any
gel bead on the Base. Each LED dot-matrix display is a 7 × 7 dot matrix,
formed by 49 LEDs. The default background color of the dot-matrix displays is
either red or blue, which indicates the team identity of the Base. The default
display characters are 1, 2, and 3, shown on three dot-matrix displays,
respectively.
Light Indicator
The light indicator indicates the team identity of the Base, the current
remaining HP, and the connection status between the intelligent controller and
the light indicator control panel. If the intelligent controller and light
indicator control panel are disconnected, the light indicator will flash
yellow.
Power Port
The power port is used to connect the power adapter to supply power to the
Base.
Camera
The camera uses a 1/4-inch sensor which is capable of recognizing objects with
specific characteristics and scanning the QR code of the competition client to
connect to the Base and the RoboMaster Champion.
Specifications
Model ：RMYTBA01
Rated Operating Voltage| 12 V
Rated Working Current| 2 A
Weight| 6.6 kg
Dimensions (Length × Width × Height)| 620×580×500 mm
Operating Temperature Range| -10° to 40℃
WIFI ：802.11 b/g/n
Frequency：| 2.412-2.472GHz，5.180~5.240GHz，5.745~5.825GHz
FCC Compliance Notice
Supplier’s Declaration of Conformity
Product name: RoboMaster Youth Tournament Base 01
Model Number: RMYTBA01
Responsible Party: DJI Technology, Inc.
Responsible Party Address: 201 S. Victory Blvd., Burbank, CA 91502
Website: www.dji.com
We, DJI Technology, Inc., being the responsible party, declares that the above
mentioned model was tested to demonstrate complying with all applicable FCC
rules and regulations.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
ISED Compliance Notice
CAN ICES-003 (B) / NMB-003(B)
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions: (1)This device
may not cause interference.(2)This device must accept any interference,
including interference that may cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.
KCC Compliance Notice
EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that
this device (RMYTBA01) is in compliance with the essential requirements and
other relevant provisions of the Directive 2014/53/EU.
A copy of the EU Declaration of Conformity is available online at
www.dji.com/eurocompliance EU contact
address: DJI GmbH, Industriestrasse 12, 97618,
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>