SunTek HC-910A 36MP 2.7K Night Vision Waterproof Hunting Camera User Manual

SunTek HC-910A 36MP 2.7K Night Vision Waterproof Hunting Camera User Manual

Product Introduction

Some Tips Before Everything

• If you observe a red flash when you take photos, please turn the switch from “TEST” to “ON”.
• After you turn the switch from “TEST” to “ON”, you will observe a countdown from 15s to ls, then the screen will shut down. This is completely normal. You can walk in front of the camera to check if it takes photos and videos.
• Do not dip the camera in the water.
• The camera can work under 160°F but please keep the camera far enough from fire to protect batteries.
• Alkaline batteries are recommended because alkaline batteries are able to provide strong and stable power to the camera.
• Please do not mix old batteries and new batteries.
• If an DC 9 V power adapter is used to supply the camera, please make sure there are no batteries in the camera in order to prevent the overcharge.

Parameter

STRUCTURE

INSTALLING BATTERIES

IF USING AA -ALKALINE BATTERIES

1. Press EJECT , the battery box will pop out.
   

2. Insert the AA batteries accordingly as indicated by the positive and negative battery icons
   

3. Slide the battery compartment back into the camera housing until it is completely engaged in the slot in the bottom of the housing.
   NOTE: Installing any of the 8-AA batteries in the wrong direction may cause the batteries to leak acid and could possibly explode, causing camera failure and damage to the battery compartment.
   

IF USING 9V DC POWER SOURCE

1. Remove the rubber port cap at the bottom of the camera.
   

2. Using a universal 9V DC cord, plug in to the bottom port option.
   

3. When not in use, replace the rubber port cap at the bottom of the camera to protect the 9V DC universal plug-in port.
   

MEMORY CARD INSTALL

INSTALL MICRO-SD CARD

1. Insert the Micro SD card (Max 256GB) with the contacts facing away. The Micro SD card should slide in freely with little resistance Continue pressing the card inward until you hear a click This means the Micro SD card is locked in place and ready for use.
   

2. To remove Micro SD card, press the card inwards to release.
   Caution: we recommend class 6 & above high speed memory card,cheap memory card may damage the pictures and videos.
   
   

3.  Slide the mode switch form OFF to TEST to activate the camera and view the user setup screen.

4. And then slide the mode switch form TEST to ON.

5. The camera will start working after 10 seconds countdown, mean while the red indicator light will blink.

OPERATION BUTTON

• Menu Button — Menu Setting
• Shutter Button — Start/End Video Recording or Photo Taking
• Video Button — Video Recording Mode
• Camera Button — Photo Mode
• OK Button — OK / Replay Mode

Tips: In replay viewing page, slide the ” ” and ” ” for browsing. Press the ” ” button, to quit the replay view page.

SETUP MENU

Setup

| Sub Menu|

Description

---|---|---
Mode| Photo,Video, Photo &Video| Camera recording mode
Photo resolution| 36/24/20/16/12/8/5/3/1MP| Different photo resolution
Photo series| 1/2/3/10 photos in series| Set photo quantity
Video resolution| 2688x1520P,1920x1080P, 1280x720P,848x480P, 720x480P,640x480P| Different video resolution
Video length| 3 seconds – 10minutes| Choose the length of video
Audio recording| On I Off| Record video sound
Shot lag| 5 seconds – 60 minutes| Interval between each

trigger

Sensitivity motion sensors| Low, Middle, High| Adjust the sensitivity of the motion detection sensor
Time lapse| On / Off| Set up time lapse mode and the length of the lapse
Target recording time| On / Off| Set the camera to record
between a certain period
Language| EN/FR/DE/IT/ES/P0FUHR/ DAN/SVE/SUO/POUPYC| camera menu language
Endless capture| On / Off| Cycle Recording
Time & Date| Set time & date Time format Date format| To set time and date
Photo stamp| Time & Date Date Off| To choose if there will be time and date on the photo
Password
protection| On / Off| Set up password to secure your camera
Format memory card| Yes / No| Delete all data on the memory card
Format memory card| Yes / No| Delete all data on the memory card
Serial NO| On / Off| Camera ID
Reset setting| Yes / No| Reset all the settings to the original settings
Version|  | camera firmware version

Camera to ON Mode

When you complete all the setting, slide switch to “ON “mode, after Red flash for 5 seconds, then the camera will start to work.

• Cautions: camera display and control panel will be useless when camera at “ON” mode, you need to slide switch back to “TEST” mode to preview the pics.

TROUBLE SHOOTING

Camera Doesn’t Capture Subject of Interest

• Check the PIR sensitivity. For warm environmental conditions, set the Sensor Level to “Low” and for cold weather use, set the sensor for “High”.
• Try to set your camera up in an area where no heat resources are in the camera’s field of view.
• In some cases, set the camera near to water will make the camera take images with no subject in them.
• Try to aim the camera over ground.
• Try to set camera on stable and immovable objects, i.e.: large trees.
• At night, motion detector may detect beyond range of the IR illumination, reduce distance setting by adjusting sensor sensitivity.
• Rising sun or sunset can trigger sensor. Camera should be reoriented.
• If person/animal moves quickly, it may move out of the camera’s field of view before photo is taken. Move camera further back or redirect camera.

Camera Stop Taking Images

• Please make sure that the memory card has enough memory storage. If the card is full, camera will stop taking images.
• Check batteries to make sure that alkaline, NIMH or lithium AA batteries left power is enough for camera to work.
• Make sure that the camera power switch is at the “On” position and not at the “Off’ or “Test” modes.
• Please format the memory card when you first time to use it or change to use another memory card.

Night Vision Flash Range Doesn’t Meet Expectation

• 4pcs AA batteries is not able to support camera night vision ability, please install 8 pcs AA batteries for better battery life
• make sure that batteries are fully charged or left power is enough.
• High-quality 1.5V NIMH or Lithium rechargeable AA batteries can offer much better Infra flash range than alkaline batteries.
• To ensure accuracy and quality of night image, please try to mount camera on dark environment without obvious light sources.
• To ensure accuracy and quality of night time image, please mount camera to dark environment without any obvious light sources;
• Certain surroundings (like trees, walls, ground, etc.) within flash range can get you better night time images; please do not aim camera to total open field where there is nothing within IR flash range to reflect flash back, it’s like shinning a flashlight into sky in night, you just can’t see anything, same does camera.

WARRANTY

With great pride and full confidence in products, we always keep our words which are given to our customers as specified warranty terms and services below. Based on a strict QC system, we initially offer all our customers one- year long time limited warranty.

Our products are warranted against defects in materials and workmanship for a period of one year from the date of original purchase. If a defect exists, we will, at our option and to extent permitted by law will.

1. repair the product at no charge using new or refurbished parts;
2. exchange the product with a functionally equivalent product that is new or refurbished.

This warranty excludes damage from abuse, accident, modifications or others that are not defects in materials and workmanship. This warranty only covers failures due to defects in materials or workmanship under normal usage. To obtain warranty service, please contact us to determine the nature of problem before return the product under this warranty (with a written description of the problem and print samples) for repairing or exchanging.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>