TOKMC W1.0 x 610 BOX and Panbrake

Product Information

The Box & Pan Brake is a tool used to bend mild steel and other sheet metals of equal yield strength. This pan and box brake is designed to fold sheet metal into boxes, pans, or trays. It can bend 16 gauge and 20 gauge mild steel. The product comes in two models: W1.0 x 610 and W1.5 x 1220A, with maximum working lengths of 610mm and 1220mm respectively.

Technical Specifications

Model Max. Working Length Weight

• 610mm 20 Gauge
• 1220mm 16 Gauge

Installation and Caution

Installation

• Please check whether all parts of this machine are fully equipped and not damaged according to the parts list or part figure.
• This machine should be mounted on a workbench or specific stand (not supplied).
• Please leave plenty of room around the machine for easy operation to avoid injury.
• Please remove the anti-rust grease on processing surfaces and some parts including kerosene.

Caution

• Please read the manual before operating and make yourself understand its structure and principle completely.
• Please do not operate the material width and thickness than table list max. Range.
• Always wear industrial standard-approved eye protection, using safety equipment such as dust mask, non-skid safety shoes, hard hat, etc.

Product Usage Instructions

Work Area

• Operate in a safe work environment, Keep your work area clean, well-lit, and free of distractions. Place lights so you are not working in a shadow.
• Keep anyone not wearing the appropriate safety equipment away from the work area.
• Store unused tools properly in a safe and dry location to prevent rust or damage. Lock tools away and keep out of the reach of children.

Operation

To use the Box & Pan Brake:

1. Make sure the machine is properly installed and all parts are in good condition.
2. Select the appropriate working length and material thickness for your project.
3. Insert the sheet metal into the brake dies and align it with the desired bend line.
4. Lower the upper die onto the sheet metal and apply pressure to bend the metal into the desired shape.
5. Repeat steps 3-4 as necessary to achieve the desired shape.

Maintenance
Lubricate the rotating parts of the machine with #32 lubricating oil regularly to ensure proper function and longevity.

SAFETY INSTRUCTION

WARNING
Read and understand all instructions before using this tool. The operator must follow basic precautions to reduce the risk of personal injury and/or damage to the equipment.

HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A notice is an alert that there is a possibility of property damage, injury or loss of life if certain instructions are not followed.

• DANGER! This notice indicates an immediate and specific hazard that will result in severe personal injury or loss of life if the proper precautions are not taken.
• WARNING! This notice indicates a specific hazard or unsafe practice that could result in severe personal injury or loss of life if the proper precautions are not taken.
• CAUTION! This notice indicates a potentially hazardous situation that may result in minor or moderate injury if proper practices are not taken.
• NOTICE! This notice indicates that a specific hazard or unsafe practice will result in equipment or property damage, but not personal injury.

WORK AREA

1. Operate in a safe work environment, Keep your work area clean, well-lit and free of distractions. Place lights so you are not working in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away from the work area.
3. Store unused tools properly in a safe and dry location to prevent rust or damage. Lock tools away and keep out of the reach of children.

Usage

This machine can be used to bend mild steel and other sheet metals of equal yield strength. This pan and box brake is designed to fold sheet metal into boxes, pans, or trays. It can bend 16 gauge and 20 gauge mild steel.

Main technical specification

26-3/4″
860 × 350 × 500mm| 1610 × 480 × 680mm
Weight| 138.9 lbs.| 474.1 lbs.
63 kg| 215 kg

 Installation and caution

Installation

1. Please check whether the part of this machine are fully equipped and not damaged according to the parts list or part figure.
2. This machine should be mounted on a workbench or specific stand (not supplied)
3. Please leave plenty room around the machine for your easy operation, in order to avoid injury.
4. Please remove the anti-rust grease on processing surfaces and some parts including kerosene.

Caution

1. Please read the manual before operating and make yourself understand its structure and principle completely.
2. Please don’t operate the material width and thickness than the table list max. Range.
3. Always wear industrial standard-approved eye protection, using safety equipment such as a dust mask, non-skid safety shoes, a helmet, and hearing protection will reduce the chances of serious injuries.
4. Do not expose the device to the rain or wet conditions.
5. Dress appropriately do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from the moving parts to avoid getting caught in the moving parts. Failure to pay attention could cause serious injury or even death.
6. It is forbidden to use the extending case to cover the handle for the purpose of lever function.

Operation

By turning the pin (#15) at the back of the frame, the eccentric case (#17) is driven to backwards. Meanwhile, the right and left eccentric handles (#07,

11) should be loosened. Therefore, the desired bending clearance can be

decided. If the thickness of blank to be bent is in the range of the rated value 16(20) gauge for mild steel, the upper die frame (#01) should be moved backward, to ensure that the clearance is twice of the thickness of the blank (from the out edge of the frame Pattern plate). The clearance may be decreased appropriately according to the bending angle, in the bending operation of non- ferrous metals.

1. The magnitude of pressure, which clamps down on the blank can be changed by adjusting appropriately the nuts (#13) on the right and left connecting rods (#9, #12).
2. If the bank is blocked when it is bent in the allowance magnitude it is may be loosened turning the eccentric handles (#07, #11) on the blocked end. The clearance can be changed by running the eccentric case (#17), which is located at the back of the frame and then, the upper die frame(#01) can be moved appropriately. After that. Clamping down again the eccentric handle on the blocked end. Therefore, the bending operation can be performed right now.
3. After the utilization of the machine to a long time, the mobile pattern plate (#03) may be deflected to a convex or a concave. This deflection can be overcome by adjusting the nut (M12) on the mobile pattern plate (#03). Therefore, the mobile pattern plate (03#) can be drawn. The adjustment does not stop unless the edge of the mobile pattern is in the same plane of the bending center.
4. Please check up the edge of upper die frame (#01) before bending operation, in order to find there is any convex or winding. If the winding edge is found, please adjust as the followings; clamps the right and the left eccentric handles (#07,#11) tight, turn the mobile pattern plate(#03) to 90 degrees, then place with another straight convex plate after that, tighten the nuts (#13) on the right and left connection rods (#09, #12).

Maintenance

Lubricate the rotating parts of the machine. (#32 lubricating-oil)

ACCESSORIES

• The inner-hexagon spanner M41 piece
• The two-head spanner 17X19 1 piece

Parts list

Assembly Diagram

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>