Kylii Kids CKF01 Floor Box User Manual

October 30, 2023
Kylii Kids

Kylii Kids CKF01 Floor Box

Kylii-Kids-CKF01-Floor-Box-PRODUCT

Product Information

The Kylii Floor Box is an interactive indoor game that comes with a lacquered aluminum box, a video projector, and a PC with a sensor to project compatible interactive games on your floor. The video projector has 6000 lumens and uses a laser projection. The box weighs 35kg and can be fixed to a ceiling of up to 4m in height using 8mm threaded rods installed by the customer. The floor where the image is projected must be clear (white or gray), mat, and pattern- free. The projection area varies depending on the height of the box and can accommodate up to 14 players.

Product Usage Instructions

  1. Ensure the Kylii Floor Box is installed on a ceiling of a maximum height of 4m using 8mm threaded rods previously installed by the customer. Do not install it on a false ceiling. Keep a 1m opening around the box if there is a false ceiling.
  2. Connect the Kylii Floor Box to a 230 volts power supply and a female RJ45 cable with an internet connection.
  3. Ensure that the floor where the image is projected is clear (white or gray), mat, and pattern-free. The floor surface must be flat.
  4. Place the Kylii Floor Box in an environment with minimal light to avoid interference with the projection.
  5. Align the projection with the axis of the sensor located inside the floor box.

Note : The assembly time for the product is approximately 4 hours, and it requires two persons. Necessary materials for assembly include screwdrivers, electric drills/screwdrivers, drills for drilling, screws (dowels, screws), electrical tools (screwdriver, tester), USB keyboard, USB extension cable (5.00 m), and an electric scissor lift (for fixation > 2m50).

If you have any questions or concerns about the Kylii Floor Box, please contact Kylii Kids at https://www.kylii-kids.com/en/contact.

Plans & technical features

Kylii-Kids-CKF01-Floor-Box-FIG-1

Description
The Kylii Floor Box is composed of a lacquered aluminium box, a video projector and a PC with sensor to project compatible interactive games on your floor. Number of players estimated /Fixing height (top of the box)

  • 250 cm : ~ 5 players
  • 300 cm : ~ 7 players
  • 350 cm : ~ 10 players
  • 400 cm : ~ 14 players

Not suitable for children under 3 years old.

Package content

  • 1 Kylii Floor box
  • 1 Videoprojector 6000 Lumens
  • 1 3D sensor
  • 1 PC
Technical specification
  • Box : Aluminium Powdered lacquered paint.
  • Technical access : 2 screwed side hatches
  • Fixation : In 4 points at the top of the box
  • Power supply (Watts) : 500 Watts
  • Video projector : Laser 6000 Lumens
  • Weight : 35kg

Installation requirements

Kylii-Kids-CKF01-Floor-Box-FIG-2

Prerequisite recap

  1. A 230 volts power supply and a female RJ45 cable with Internet connection.
  2. The box must be fixed on a ceiling of a height of 4m MAXIMUM (center distance 10 cm x 10 cm). The threaded rods (8 mm diameter) previously installed by the customer must be 1m maximum (no fixing on false ceiling)
  3. If there’s a false ceiling under the ceiling, make sure to keep a 1 m opening in the false ceiling all around the box. This opening ensures access to the equipment in order to do maintenance.
  4. The floor where the image is projected must be clear (white or gray) mat and pattern-free. The floor surface must be flat.
  5. The box shouldn’t be placed in an environment with too much light (glass roof, bay window or spotlight above the projection area).

Warning !
The projection is straight and must be always aligned with the axis of the sensor located inside the floor box.

Kylii-Kids-CKF01-Floor-Box-FIG-3

Height Fixation (top of the box)

|

Bottom of the box

|

Projection area

|

Number of players

---|---|---|---

Length

|

Width

|

m2

2,5 m| 1,9 m| 2,4 m| 1,8 m| 4,3| 5
3m| 2,3 m| 3m| 2,2 m| 6,7| 7
3,5 m| 2,9 m| 3,7 m| 2,7 m| 10,2| 10
4m| 3,4 m| 4,3 m| 3,2 m| 14| 14

The mounting height refers to the top of the box, not the ceiling height. The size of your support (threaded rods) must be considered. The projection area is an approximation. It may vary during installation. This projection area can be reduced to fit your room.

Assembly instructions

Indication of assembly

  • Indicative assembly time : 4 hours
  • Number of persons 2

Necessary material:

  • Screwdriver and electric drill/screwdriver
  • Drill with percussion (Drill) & drills for drilling
  • Screws (dowels, screws ..) and electrical tools (Screwdriver; tester …)
  • USB keyboard
  • USB extension cable 5.00 m
  • Electric scissor lift (for fixation> 2m50)

Installation step to follow

  1. Open the side doors of the box
  2. Pass your power and network cables in the box (opening on the sode of the box) and fix the box on your ceiling or your mount.
  3. Connect your network input to the router (yellow port) and your power supply to the breaker.
  4. Put the video projector in the box (Be careful to the positioning direction)
  5. Connect the power supply, the network cable (to the router) and the HDMI cable from the Video Projector to the P.C.
  6. Position the lens of the Video Projector being careful not to drop it or damage or dirty it. (see the video projector manual provided)
  7. Close the side doors of the box and turn the system back on.

Important information
Check that your power supply and network cable are working properly before installation. Always work off when installing the equipment. Secure your work area if you are working on a place open to the public. For your safety, we recommend the use of a secure nacelle as a workstation for mounting this equipment and to secure your environment if you operate in a place open to the public. Whether you attach the box to your ceiling directly or through a bracket, make sure that it can support a weight of 35 kg and make sure to adapt your hardware according to the type of mounting bracket.

Position of the video projector
Position the location for the lens down and orient the feet of video projector on the outside of the box

Equipment Configuration

Internet Connection

  1. Connect a USB keyboard to the USB connector of the Box
  2. Press “ALT + C” to open the configurator
  3. For a wired connection, choose “LAN”
  4. Choose your connection type “AUTO” or “MANUAL”
  5. If you chose “MANUAL”, complete the required fields
  6. Then select “EXIT” to close the configurator
Setting up the equipment

Games selection
If you have chosen a game pack, they are already installed on your equipment when you receive it. If you wish to add more games, please contact our customer service. If you have chosen a subscription, your equipment comes with a selection of games from our catalog. To change / add games, please follow the steps below:

  1. Log on to www.kylii.eu with your login information
  2. Choose your equipment from the drop-down list on the right
  3. Add / Remove games in your program list
  4. Save by choosing an immediate synchronization or the next start synchronization of the equipment

Settings of the play area

  • Connect a keyboard to one of the computer’s USB ports

  • When the system has fully started and the games appear on the ground, press the key combo “Alt + C” and wait until the configurator appears (see screenshot below)

  • Using the arrow keys, highlight the “Setup” button and press “Enter”Kylii-Kids-CKF01-Floor-Box-FIG-5

  • Make sure the area visible by the sensor is empty (no object or person located under the sensor).

  • Use the arrow keys to highlight the “Start” button.

  • Then the sensor starts its calibration for about one minute.
    During calibration, no object / person should pass under the sensorKylii-
Kids-CKF01-Floor-Box-FIG-6

  • Once the calibration minute has elapsed, the camera screen must be completely black. If not, restart the calibration by highlighting the “Reset” button and pressing the “Enter” button.

  • If the camera’s screen is completely black, highlight the “Next” button and press the “Enter” buttonKylii-Kids-CKF01-Floor-Box-FIG-7

  • Back on the main menu, highlight the “Playground” button and press the “Enter” button on the keyboard.Kylii-Kids-CKF01-Floor-Box-FIG-8

  • This new screen allows you to adjust all the settings of the game area (size, position, detection setting depending on the height of the sensor …) The final gaming area will be the black part of the screenKylii-Kids-CKF01-Floor-Box-FIG-9

  • First, using the projector’s remote control, move the projection using the “Lens Shift” button and the “up” and “down” arrows on the remote control : the yellow cross has to be located right under the 3D sensor (cf the following diagram)Kylii-Kids-CKF01-Floor-Box-FIG-10

  • Warning! Do not change anymore the projection location / the lens shift using the remote control once this step has been done.

  • To change the location of the gaming area : use the arrow keys on the keyboard and the round + and – buttons to change the position of the floor projection (right / left, up / down). To do this, highlight the selected button and press the “Enter” key on the keypad as often as necessary.

  • To change the size of the gaming area : highlight the “Resize” button using the arrows of the keyboard and press “Enter”. Using the directional keys on the keyboard and the round + and – buttons, change the position of the projection on the floor (height, width). To do this, highlight the selected button and press the “Enter” key on the keypad as often as necessary.

  • To improve the quality of the detection depending on the height of the bottom of the box : highlight the “Detection” button using the arrows of the keyboard and press “Enter”.

  • It is then possible to set two detection parameters: erosion and expansion.

  • Depending on the height at which the bottom of the box is located, adjust these parameters by referring to the table below.

**Height *** Erosion Dilatation
2m 7 6
2,5m 6 7
3m 5 9
3,5m 4 9
4m 4 10

The indicated height corresponds to the height of the lens of the video projector and therefore at the bottom of the kylii floor box.

Make sure to observe the following assembly instructions and operating instructions before using and commissioning the equipment.

Equipment positioning
This equipment is intended for indoor use only for ceiling mounting. Do not place near any heat sources such as radiators, heat registers, stoves, or amplifiers. Its operating temperature is from 5ºC to 35ºC. Do not place the furniture in a confined space unless the space is sufficiently ventilated. Using the game in an environment where the temperature varies greatly can damage the equipment. Prevent the equipment from getting wet. To reduce the risk of fire or shock, do not expose the equipment to rain or other types of moisture. No obstacle or injurious element should be present near the equipment. The floor of the installation area must be non-offensive and of a light, neutral colour (Example: grey or beige PVC floor). The box must be fixed at a height between 2m50 and 4m50 (top of the box)

Power supply
Check that your power outlet provides the type of power indicated on the technical data. Do not use non-standard power sources, such as generators or inverters, even if the voltage and frequency appear acceptable. Only use AC power supplied by 2P + T connectors. Check that your outlet can handle the current (in amperes) needed to power the equipment and any other device powered on the same circuit. Put all the cables so that no one (or any animal) can kick or pull on them.

Internet Connection
An internet access must be configured via an RJ45 cable to access the various Kylii services (update, change of games …). It must be a permanent Internet connection (no public wifi, wifi per session or LDAP connection, no proxy). If you have a secure connection, make sure all the rights are open and take the necessary steps to access, send and receive information and data from Kylii Kids’ servers.

Equipment Maintenance
Regular inspection and cleaning are the basic principles; To clean the equipment, use a soft, damp cloth: • Do not use abrasive pads, detergents, scouring powders, solvents or other liquid, or aerosol cleaners. Clean the inside and outside regularly and take care to remove the dust present. To avoid scratches, gently rub the lens of the Video Projector with a soft, lint- free cloth. You can moisten the cloth with water or eyeglass cleaner, but do not spray liquid on your lens. Do not use glass cleaner or other chemical detergents.

Revision date: 02/10/2022 © Copyright Kylii Kids

Interactive indoor game

  • Reference : CKF01
  • Model : 42

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals