BIG CLINKER Q EP Tile Cutter Owner’s Manual

BIG CLINKER Q EP Tile Cutter

Instructions for Cutting Tile

1. Adjust the protractor gauge for the proper tile size and place the tile to the most forward position of the cutter against the stop.
2. Place the cutting wheel on the rear edge of the tile and slide the wheel forward by pushing the handle down, scoring the tile as the handle is pushed forward. It is important to make this scoring cut in one continuous motion, scoring only once per tile.
3. After scoring, and without moving the tile, position the handle so that the breaker foot is directly above the tile’s front edge at the stop. Apply increasing pressure on the handle until the tile snaps along the score line.

Notes:

1. The 10500, 10600, and 10800 Big Clinker Tile Cutters have an adjustable height (three scoring positions and one retracted position) wheel which permits easier cutting of up to 3/4″ thick tiles, and makes cutting of mosaic possible as the wheel can be moved up to permit the breaker foot to operate at any position along the rails.
2. Oil should not be used on the 10500, 10600, and 10800 Tile Cutters. Use of oil will cause eventual gumming and sticking of the movable parts as the oil combines with dirt and ceramic tile dust.
3. Wear is normal in the chrome plated rails and can be evenly distributed by occasional rotation of each of the two rails. For cutters with hex bolts holding the rails, loosen each hex bolt and slightly rotate the rails. Retighten the hex bolts when finished.
4. The only part routinely needing replacement is the carbide scoring wheel. All other parts are also available, if needed.

MODEL

Height of Cutting Wheel Adjustable to Four Levels
The height of the cutting wheel can be adjusted to four levels according to the thickness of the tile by one-touch motion. Therefore, tiles of any thickness can easily be cut.

Easy Cutting of Mosaic Tile
When cutting mosaic tile, after scoring is completed, the first tile can be cut as long as the Breaker Bar hits the tile lightly. If the cutting edge is stuck at the second tile, raise the wheel a little by turning the knob so that subsequent tiles can easily be cut.

PARTS LIST

STK# 10500 20 In. Big Clinker Tile Cutter
PART NO. DESCRIPTION

• 10502: Box
• 10502-2/3: Replacement Pads (2)
• 10503-4: Rail Bars (2)
• 10503-5: End Bracket
• 10502-15C: Guide (Complete with Clamp Lever)
• 10504-20: Slide Assembly
• 10500-21: Bearing Assembly Only
• 10501-28 : Handle with Grip
• 10501-29: Grip
• 10501-32: Breaker Bar
• 10502-34 : Holder for Ball Bearing Wheel
• 10504-36 : Holder for Ball Bearing Wheel
• 10504-37M: Holder for Ball Bearing Wheel Handle (Complete with Holder for Ball Bearing Wheel, Breaker Bar & Slide Assembly with Bearings – 20, 21, 28, 32, 34)
• 21123: 12 Aluminium Arm with Magnet (2) 7/8 Titanium Coated Tungsten Carbide Ball Bearing Cutting Wheel

STK# 10600 24 In. Big Clinker Tile Cutter

PART NO. DESCRIPTION

• 10602: Box
• 10602-2/3: Replacement Pads (2)
• 10603-4: Rail Bars (2)
• 1 0603-5: End Brackets
• 10601-15C: Guide (Complete with Clamp Lever)
• 10604-20: Slide Assembly
• 10600-21: Slide AssemblyBearing Assembly Only
• 10601-28: Handle with Grip
• 10601-29: Grip
• 10601-32: Breaker Bar
• 10601-34: Holder for Ball Bearing Wheel
• 10604-36: Handle (Complete with Holder for Ball Bearing Wheel, Breaker Bar & Slide Assembly with Bearings – 20, 21, 28, 32, 34)
• 10604-37M: 12″ Aluminium Arm with Magnet (2)
• 21119: 7/8″ Tungsten Carbide Ball Bearing Cutting Wheel

STK# 10800 27 In. Big Clinker Tile Cutter
PART NO. DESCRIPTION

• 10801: Box
• 10801-2/3: Replacement Pads (2)
• 10803-4: Rail Bars (2)
• 10803-5: End Brackets
• 10800-15C : Guide (Complete with New Clamp Lever)
• 10804-20: Slide Assembly
• 10800-21: Bearing Assembly Only
• 10800-28: Handle with Grip
• 10800-29: Grip
• 10800-32: Breaker Bar
• 10800-34: Holder for Titanium Coated Ball Bearing Wheel
• 10804-36: Handle (Complete with Wheel Holder)
• 10804-37M: 12ª Aluminum Arm with Magnet (2)
• 21123: 7/8* Titanium Coated Tungsten Carbide Ball Bearing Cutting Wheel

LIMITED WARRANTY

Refer to warranty card.

Boca Raton, FL 33487
www.gep.com
E2112-6820

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>