Mazhaoli F110 Ride on Floor Scrubber User Manual

F110 Ride on Floor Scrubber

Product Information: F110 Ride-On Floor Scrubber

The F110 Ride-On Floor Scrubber is a machine designed to clean large areas of floors efficiently. It has a control panel, clean water tank, sewage tank, brush plate part, and water absorption pickling system. The machine is equipped with a seat switch and an electronic brake for safety and convenience. It has a theoretical efficiency and maximum working duration. The battery type, brush motor, suction motor, and net weight are also specified in the technical parameters.

Product Usage Instructions

1. Read the user manual carefully before operating the machine to ensure safe and convenient use. The manual provides detailed illustrations and instructions on how to use the machine.
2. Check the packing list to ensure that you have received all the necessary items, including the user manual, warranty card, and warranty hangtag.
3. Take note of the general remarks, warnings, and important notes in the manual to avoid injury or damage to the machine and the surrounding area.
4. Familiarize yourself with the control panel and its key functions, including the automatic/stop seat, gas pedal/electronic brake, dirty water outlet/flexible hose, vacuum hose, squeegee, and adjustable soap pump.
5. Check the clean water tank and add water as needed. Mix it with detergent before use.
6. Adjust the brush plate part to distribute clean water to the ground and remove dirt from the floor.
7. Use the water absorption pickling system to recover sewage from the ground.
8. Make sure to follow the wiring mode specified for the battery box.
9. After use, clean the machine thoroughly and store it in a safe place.

General Remarks

Please read this instruction carefully before performing any operation on the machine

Contents of the Manual
The manual is drafted by the manufacturer and written as a part of the machine as a whole. It contains all the specific requirements of the machine being produced.This manual contains the basic information that the user must have.Other documents are also described, which contain specific technical information on maintenance.Follow the manual to ensure the safety of operators and machines.At the same time, the machine running consumption is low, the cleaning effect is good and the working time is long.Failure to follow the manual can harm workers and machinery, damage the working ground, and even the environment.
Look at the table of contents in the front section of the manual for the fastest way to find specific topics. The following sections are not to be ignored, so be sure to note the bold text and graphic instructions below .

Danger
It means you must be careful and understand the instructions carefully, or you may get injured or even die.

Important Note
Must pay attention to careful operation, to understand the instructions, otherwise it will cause a series of adverse consequences. Such as: damage the machine, damage the place where the machine is used, thus causing economic losses.

Information
Operations requiring Special Attention Since the manufacturer will make necessary updates and improvements to the product, the manufacturer has the right to update the machine without any prior notice. The machine may be slightly different from the icon in the manual, but the information and safety displayed in the manual can be guaranteed.

Technical parameters

Packing list

1. User manual
2. Warranty card
3. Warranty hangtag

F110

Technical information

Overview
This machine is a fully automatic floor scrubber machine, which can be cleaned in residential or industrial environments, and can be self-activated to wash and dry the floor. The floor scrubber can automatically distribute detergent and clean water to the floor to clean and remove dirt. Choose the right cleaner and scrub brush. The machine has built-in water cleaning tank and sewage tank, which can complete the function of water absorption while washing the ground. The working principle of water absorption function is to use the water absorption motor installed in the sewage tank to form a vacuum water absorption device, and absorb the sewage on the ground and recycle it into the sewage tank through water absorption.

The main parts of machine
As shown in FIG. B:

1. Clean water tank (FIG.2, add water cover) : carry clean water and mix it with detergent;
2. Sewage tank (FIG. 3) : recovery of sewage and sewage outlet on the ground;
3. Control panel (FIG. 1);Introduce the meeting board in detail;
4. Brush plate part (FIG. 10) : the main component is the brush, which distributes clean water to the ground and then remove dirt from the ground;
5. Water absorption pickling system (FIG. 3) : It is used to recover sewage from the ground.
6. Battery box (FIG. 11) : Mainly introduces the wiring mode.

Hazardous area

1. Water tank system: When using a certified detergent, avoid spills of detergent to the eyes, skin, etc.;
   Hazards arising from the collection of dirt from the environment (bacteria and chemicals);Removing the waste tank from the clean tank may cause a hazard

2. Control panel: Danger of short circuit.

3. Bottom of brush plate: Brush rotation can be dangerous.

4. Rear wheels: Rear wheels and underframe pose a risk of crushing.

5. Battery box: The electrode will cause a short circuit hazard, and gas will be generated when charging.
   Pay attention to the installation wiring mode.

Safety

Safety regulations
Please read the “User manual” carefully before starting and using the machine, or before performing maintenance and operation.

Important Note

• Please strictly follow all instructions in this operation manual (especially the danger and warning section) and all safety warning labels on the airframe. The manufacturer shall not be liable for damage to persons or property resulting from violation of operating instructions.
• The machine must be operated and used by trained personnel who must be familiar with the operation and trained. Minors are strictly prohibited from using the machine.
• The machine cannot be used for other purposes beyond the design scope. All safety standards and regulations must be strictly adhered to when used in special circumstances such as pharmaceuticals, hospitals, chemical industries, etc.
• The machine should not be used in dark and dark places, places prone to explosions, places where there are harmful substances to human body and inappropriate environments.
• The appropriate temperature of the machine is +4°C to +35°C. When the machine is at rest, the temperature is +0°C to +50°C.
• The machine cannot be used to absorb inflammable and explosive liquids (such as gasoline, fuel oil, etc.) when the atmospheric humidity of the machine is 30% to 95%.
• Flammable gases, dry dust, acid and soluble substances (e.g. soluble paint, propylene copper, etc.).Objects that do not absorb the heat of combustion.
• Do not operate on sloping surfaces or slopes with a gradient greater than 16%.If the machine is working on a small slope, do not use it crosswise. Be very careful and do not retreat. When driving along the slope, pay special attention to prevent the machine from toppling over, do not accelerate suddenly. When driving on the slope, the brush plate and suction grill must be raised. It is forbidden to park the machine on the slope at any time. When the motor of the machine does not stop running, the operator is forbidden to leave the machine. Before leaving the machine, switch the motor on and off Turn off and disconnect the power to make sure it doesn’t move suddenly. No matter where you are doing your work, please pay attention to the people and children present at your work site. Do not use the machine for transport or drag other objects.
• Do not drag the machine. Do not store anything above the machine.
• Do not block the ventilation and cooling areas.
• Do not move, modify or cover safety devices.
• Experience has shown that sorting out personal belongings during work can lead to serious accidents. Before you start work, take off your jewelry, watch, tie, etc. Staff must wear and wear protective clothing and protective gear -protective aprons/covers, non-slip waterproof shoes, rubber gloves, eye protectors Hoods and hats, earplugs, masks, etc.
• Do not place hands in moving parts. Do not use cleaning agents that do not comply with regulations. Use only in accordance with safety guidelines.
• We advise against exposing children to cleaners. In case of contact with eyes, rinse immediately with clean water. If inhalation occurs, contact your doctor immediately. Please make sure that the socket connecting to the battery charger power supply is properly connected and the protective switch is used.
• Make sure the plug is in line with the current/voltage supplied by the machine. The battery must be used in accordance with the guidelines of the battery manufacturer and local laws. The surface must be kept clean and dry to prevent surface leakage. Batteries must be kept away from metal dust.
• Do not leave any tools above the battery, it will easily cause battery short circuit and explosion. Strict safety guidelines must be followed when using acid batteries. Machines operating in high magnetic fields can easily cause electronic control systems to fail. It is strictly prohibited to spray and wash the machine directly with water gun.
• Waste water, detergent and so on recycled while the machine is working should be treated according to local laws.
• If the machine is out of control due to any malfunction during operation, please shut down the machine immediately (unplug the main power supply), and then immediately contact the factory technician as soon as possible. All machine maintenance operations must be performed in an adequately lit area and the battery connection must be disconnected.
• All circuit parts and all maintenance operations must be performed by certified technicians. This machine can only use the accessories and spare parts provided by the original factory to ensure the safety and operation of the machine.
• Do not use spare parts that have been removed from other machines.
• The designed service life of the machine is 10 years. After the service life, no matter whether the machine continues to be used or not, the machine must be scrapped according to the local laws and regulations: the machine must be disconnected from all the power supply and drained out all the liquid and detergent; This product is a special waste of WEEE type and is applicable to the new environmental protection regulations. It must be separated from daily waste and sorted according to local laws..

Special waste. It must be treated separately from regular rubbish.
The machine may be returned to the manufacturer for refurbishment. If the machine is no longer in use, it is recommended that used batteries be sent to a certified disposal center for disposal.
You must ensure that all harmful parts are handled safely and out of the reach of children.

Operation and installation

Transportation and lifting of machines (including packaging)

Important Note
During the lifting operation, the machine must be fixed safely to avoid the accident of turning over or falling. When using forklifts to transport machinery, it must be carried out in a well-lit environment.

The machine is fixed to the wooden floor by the manufacturer when leaving the factory. It must be loaded onto the transport vehicle with appropriate equipment (see EC Directive 89/392 and additional documents).Upon arrival at the destination, the equipment must be loaded and unloaded using the same machine. The absorbent pick of the machine is packed with plastic protective film. When using a forklift to move the machine, it must be operated together with the packing. During operation, care should be taken to avoid machine collision and overturning.

Inspection of transportation process
When receiving the machine, please check whether the machine and packing are damaged during transit. If any damage is found to the machine or packaging, please inform the shipper and fill out a claim for compensation.

Remove the packing
Important Note
When unpacking the machine, the operator must be equipped with the necessary tools (gloves, goggles, etc.) to minimize the occurrence of accidents.

Please follow these steps to remove the machine:

• • Use scissors and pliers to cut open the plastic tape
• • Remove the carton
• • Remove the metal supports for fixing the machine from the wood floor according to the machine model
• • Push the machine backward from the wooden floor using a ramp plate
• • Remove packaging for brushes and water-absorbent pickles
• • Clean the surface of the machine according to safety rules
• • After removing the machine, the battery can be installed. If possible, please take care of the removed packaging materials so that the machine can be protected when it needs to be transported again or sent to the maintenance center for repair. Otherwise, please dispose of the packaging according to local laws.

Danger
The above guidelines must be strictly observed, otherwise it may cause accidental injury and danger , and may result in the loss of warranty rights of the machine

The machine may be equipped with two types of batteries
AGM/Colloidal battery: this type of battery is main enation-free. The parameters of the battery must be within the range specified in the technical specification of the machine. If the battery is too heavy, it will cause the machine to turn dangerously and the motor to overheat. If the battery capacity is too small, the machine will be charged more frequently. The battery must be kept charged regularly, the surface must be kept dry and clean, and the cable must be connected Make sure the connection is intact.

Information
Please follow the following guidelines to set the machine according to the type of battery used.
Battery model: The jumper switch for battery type setting is located behind the control panel (FIG. N), please move the jumper to make the appropriate setting (ACID wet battery /GEL maint-free battery) according to the battery type selected.

Battery: Preparation
Danger
During the installation or maintenance of any battery, the operator must prepare the necessary equipment (e.g., gloves, goggles, protective clothing…Etc.);To prevent the risk of accidents, keep away from the flame, prevent the electrodes of the short-connected battery, prevent sparks and do not smoke. Under normal circumstances, randomly provided batteries are acid, ready to use;If the supplied battery is a battery without water (without acid), the following steps must be followed before installing the battery to the machine:

• • Open the battery cap and add an acidic electrolyte (density between 1.27 and 1.29 kg 25° C) to each battery unit, making sure that the metal plates are fully immersed in the solution;
• • Leave it idle for 4-5 hours to make the acidic electrolyte fully react with the electrode plate;
• • Check that the solution level is still above the metal plate; If not, fill the solution to the level;
• • Put the cap on the electric bottle;
• • Install the battery to the machine (according to the instructions below). Before using the machine for the first time, please charge the battery according to the following steps.

Battery: Installation and connection
Danger
Check that all switches on the control panel are in the “0” (off) position. Make sure that the battery wire connection is marked with a “+” terminal connected to the positive pole of the battery. It is strictly prohibited to check the battery in the presence of sparks. Please follow these steps carefully. A short circuit in the battery can cause an explosion.

1. Please ensure that the water in both tanks is drained (if necessary, please drain according to the relevant section).

2. Turn the sewage tank backward and rotate to 90°. Expose the battery tank.

3. Place the battery in the battery box.
   Important Note
   Please make sure that the weight of the installed battery is suitable for your machine.

4. Connect the battery wire according to the wiring diagram (FIG. 11).

5. Place the sewage tank in its normal working position

6. Please use the machine according to the following guidelines.

Battery charger
Important Note: Do not discharge batteries excessively, as this can cause permanent damage.

Battery charger Selection
Please ensure that the battery charger matches the installed battery:

• *Read-acid battery with water: it is recommended to use automatic charger
• • according to charger manufacturers and manual to choose.
• • AGM/gel battery: it is recommended to use a dedicated charger.

Preparation of charger
If you are using a charger that is not supplied at random, you must use the supplied connector to install it on the charger. Please follow these steps to install the connector:

1. from battery charger cables (red and black) to remove the protective layer about 13 mm respectively;
2. insert the wire into the connector terminal, and then use pliers clamp;
3. will terminal according to the polarity (red + black line -) installed to the connector.

• Connect the charger connector to the charging connector of the machine

Transportation and lifting of machinery
Important Note
All operations must be performed in a well-lit environment and must follow all safety guidelines. Operators must wear safety protective clothing.

To pack and ship the machine, follow these steps:

1. Drain the two water tanks;
2. Remove absorbent gripper and brush (or baijie mat);
3. Remove the battery;
4. Place the machine on the wooden floor and fix it with metal bracket and packing belt;
5. Use the forklift to load the wooden floor (including the machine) onto the transport vehicle;
6. Fasten the machine and the wooden floor to the vehicle using the seat belt.

User Instructions

Controls-describes the controls and panels of the machine

1. Water output indicator: The current water output indicator automatically adjusts the water output position by default, with 3 grids as the first gear, 5 grids as the second gear, and the full grid as the third gear (the maximum). The indicator light goes out completely and shows no water.
2. Water flow mode switch: press the button to manually adjust the water flow mode, press the button for 3 seconds to automatically adjust the water flow mode, and power on automatically adjust the water flow mode by default;
3. Water absorption function button: The water absorption motor and water absorption rake can be started and stopped separately;
4. Emergency stop switch;
5. Horn switch;
6. Front light switch;
7. Working state indicator of walking motor: When the indicator is on, the walking motor functions normally. When the indicator goes off or flashes, the walking motor fails;(Make sure someone sits in the chair)
8. ECO button: Simply press on or off ECO Energy-saving mute mode;
9. Battery indicator: The full grid is 100% full, charging should be carried out when the remaining 3 grids are left;
10. Main brush pressure button: the default pressure is 1, and the main brush pressure can be adjusted according to cleaning requirements, L:45Kg,M:60Kg,H:75Kg;
11. The knob for detergent gear: 0 for no detergent, mixing ratio 1:12 for gear 1, 1:64 for gear 2, 1:32 for gear 3;
12. One-click start button: press it once, and enable the function of floor washing and water absorption;
13. Forward and Backward switch key;
14. Speed limit knob: turn counterclockwise to reduce the driving maximum speed; turn clockwise to increase the driving maximum speed;
15. Brush loading/unloading button: press once to execute the brush loading action; Press for 3 seconds to discharge the brush.
16. timing display: display time, unit: hours;
17. Indicator light of water quantity in the water tank: when the water in the water tank is short, the indicator will always turn on. The indicator will prompt error code.
18. Sewage tank water quantity indicator light: when the sewage tank is full of water, the indicator will always go on with error code, the water absorption function will stop, and the indicator light will go out after sewage discharge;

Installation and adjustment of squeegee
Squeegee (FIG. 3) is used to drain sewage from the ground. Please follow the steps below to install water absorption gripper:

1. Please make sure the squeegee (FIG. 3) is in a reduced state. Put the water absorption gripper down.
2. Install the squeegee on the bracket (FIG.3)
3. Tighten the two fixed knobs (FIG.3)
4. Insert the suction pipe (As shown in FIG. 3) completely into the squeegee; Suction hose strips can scrape water and detergent off the floor. In order to make water absorption effect more perfect, after a period of time, long-term friction with the ground will make the edge of the rubber strip become blunt and become split, affect the effect of water absorption, so it is necessary to replace the water absorption strip. Water suction strip must be checked frequently.

Installation and replacement of brushes/discs
Important Note It is strictly prohibited for the machine to work without a brush or needle tray.

Automatically install brush (or pin tray)

1. Push the floor brush or pin tray toward the center of the brush until the floor brush or pin tray is placed in the center of the brush (FIG.10);
2. Press the brush installation and unloading button (control panel, Figure 15), and the floor brush will be installed automatically. Press only once to execute the brush loading action; Or use the brush mounting plate to position the brush for installation, as shown in the figure below

Refer to the fixed point for a total of 4 points (left and right direction) on the brush
Remove the brush (or pin tray)

1. Stop all service functions of the machine
2. Press the brush installation and unloading button (control panel, Figure 15) and hold for 3 seconds to perform brush removal; The floor brush falls off automatically. Remove the floor brush.

Detergent-How to use it
Important Note

Dilute the detergent according to the manufacturer’s instructions, do not use bleach and oxidants (especially the high-concentration type), do not use fluxes and hydrocarbons,
do not use the detergent at a temperature beyond the specified range, do not contain sand and impurities.

This machine can only use low-foam cleaners specially designed for floor cleaners. Please contact the manufacturer for the latest and full detergent information. Please select the appropriate cleaner according to the condition of the floor and dirt. Please use the cleaner according to the relevant safe hand.

Preparation before work
Important Note
Before the machine starts to work, please wear protective clothing, hats, boots and so on according to the working environment, and wear mask to protect the respiratory system according to the advice of the detergent supplier

Please check the machine according to the following steps before work:

1. Check the battery power. If the battery is low, please charge it first;
2. Check whether the sewage tank (FIG. 3) is empty. If there is sewage, please drain it.
3. Add clean water and low-foam cleaner in proportion to the inlet on the left of the clean water tank (FIG. 2).Do not over fill the water, and keep the water above 5 cm from the water inlet;
4. Select and install suitable brushes and clean pads according to the ground environment.
5. Please ensure that the suction hose is properly connected to the suction hose (FIG. 3) and the suction hose is in good condition.

Information
If it is the first time for the operator to use the machine, please train in a wide space to use the machine. Please drain the water from the sewage tank before adding water to it.

In order to achieve the best cleaning effect and the longest service life of the machine, please use the machine according to the following simple rules:

1. Please tidy up your work area first and remove as many obstructions as possible.
2. Please try to work in less time so that the ground will not be contaminated again.
3. When cleaning, the machine should run as straight as possible
4. The large area to be cleaned is divided into several rectangular areas and cleaned separately. If necessary, use a mop or cloth to clean corners.

Machine working
Machine startup Prepare the machine as described below.

1. Turn the key switch (FIG. 1) to the “ON” position without stepping ON the accelerator pedal (FIG. 1), and check the battery power through the display (control panel).If the battery is low, turn the key switch back to the “OFF” position to charge the battery (see Chapter 8).
2. Use the shift switch (control panel) to select the walking direction of the machine.
3. Turn the steering wheel by hand and press down the accelerator pedal (FIG. 1), and the machine starts to move.

Information
The seat (FIG. 1) is equipped with two safety induction switches that enable the machine to walk only when the operator is seated.

Information
Start to work, control the steering wheel by hand, use the shift switch of the walking direction of the machine (FIG. 1) to select the walking direction, and then press the accelerator pedal (FIG. 1) to walk.

Important Note
To prevent ground wear, avoid using brushes in situ.

Stop of machine

1. Release the foot pedal (FIG. 1). The machine is equipped with the electromagnetic brake system. When the foot pedal is fully released (FIG. 1), the electromagnetic brake braking will automatically take effect. Close the one-click start button to raise the brush lever and stop the main brush.
2. Turn the key switch (FIG. 1) to the “OFF” position.

Important Note
Every time you need to add water to the water tank, please drain the water tank first.

Danger
Operators should wear appropriate protective clothing.

When the sewage tank is full, the indicator light goes on (control panel).1) After a few seconds, the suction machine will automatically cut off the power. You must stop working and drain the sewage tank.

Sewage tank drainage:

1. Drive the machine to a position where drainage can be performed

2. Release the foot pedal (FIG. 1) and stop the machine

3. Use a drain pipe (FIG. 3) to discharge sewage.
   Clear water tank drainage:

4. First, execute according to point 1-3.

5. Unscrew the drain cap (FIG.7) and drain out all the clean water after finishing the work every day.

Important Note
When cleaning the sewage tank, do not take out the filter (FIG. 7) and do not shoot directly at the filter with water. Now you can get back to work.

To push or drag a machine:
When the machine fails or runs out of power and cannot walk, in order to push or drag the machine, the electronic brake control lever on the walking wheel must be tightened (Figure 6), and the control lever must be relaxed after the drag line is completed.

Important Note
If the brake switch (FIG. 6) is not relaxed, the electronic brake system will fail.
When the electronic brake system fails, it is strictly prohibited to
operate the machine. When the machine needs to be pushed or dragged, the brake switch needs to be operated (FIG.6).

The machine stopped running for a long time
If the machine is not in use within a long period of time, remove the squeegee and brush (pin tray), clean the machine and accessories, and store them in a dry place (preferably in a sealed plastic container).In addition, please ensure that the sewage and water tank inside clean. Battery model: Before the machine stops using for a long time, please fully charge the battery and then store it. During storage, the battery should be charged at least once every two months to prevent damage to the battery.

Important Note
Batteries may be permanently damaged if they are not periodically charged.

Battery maintenance and charging

Danger
During the installation or maintenance of any type of battery, the operator must prepare the necessary equipment (e.g., gloves, goggles, protective clothing…Etc.);To prevent the risk of accidents, keep away from the flame, do not short connect the battery electrode, do not generate sparks and do not smoke, and do not charge in a ventilated environment.

Use a charger for charging
(FIG.12, position. 8) Connect the charging cable to the connecting base (FIG.12). Turn on the charger

Important Note
If using colloidal battery, charge according to the charger manual;

Machine maintenance instruction

Danger
Be sure to disconnect the machine’s main power supply before performing any maintenance.Maintenance of all electrical parts must be carried out by certified and trained professionals and must comply with safety rules and instructions.

Maintenance – Overview
(FIG.12, position. 8) Connect the charging cable to the connecting base (FIG.12). Turn on the charger
According to the manufacturer’s guidelines for routine maintenance to help the machine to obtain the best performance and prolong the life of the machine each cleaning machine please follow the following steps:

1. Use water spraying device carefully. Water spraying device may easily allow water to enter circuit board and motor, resulting in short circuit or machine damage.
2. Do not use fluxes and hydrocarbons, which may cause damage to rubber parts.

Routine maintenance
Filter screen and float ball sensor of water absorption motor: clean

1. Open the upper cover of the water tank on the sewage tank (FIG. 7);
2. Drain the sewage from the sewage tank;
3. Take out the filter;
4. Clean the filter screen with clean water or detergent;
5. Reinstall the filter.
6. Close the lid of the sewage tank.

Clean water tank filter: Clean

1. Close the outlet valve before cleaning the filter (FIG. 9).
2. Screw out the outer cover of the filter (FIG. 8);
3. Pull down the filter;
4. Clean the filter screen with clean water or detergent;
5. Reinstall the filter on the bracket
6. Reinstall the filter cover

Water absorption scraping tape:
Water absorbent tape is installed on the water absorbent pick, used to stick to the ground to recover sewage and detergent. After using for a period of time, the rubber strip will wear because of friction, thus affecting the water absorption effect, so please check the condition of the rubber strip frequently.

Flip or replace the adhesive tape:

1. Unscrew the two fixed knobs (FIG. 3 Position of water absorption gripper) and remove the water absorption gripper from the bracket
2. Remove the vacuum tube from the suction scraper (FIG. 3, vacuum tube);
3. Remove left and right retaining nuts
4. Remove the adhesive tape retaining clip
5. Remove the tape
6. Turn over the rubber strip until the four sides of the rubber strip are worn away, or replace the new rubber strip;
7. Reinstall the adhesive tape retaining clip and retaining nut

Periodic maintenance

Daily maintenance
After each day’s working, please follow the following guidelines for maintenance:

1. Drain the sewage from the sewage tank;
2. Clean and check the condition of the water-absorbing strip, and replace it if necessary.
3. Check whether the suction outlet of the suction grill is blocked. If necessary, please clear the blockage;
4. Charge the battery according to the instructions.

Weekly maintenance
Clean the sewage tank and switch the ball float to ensure the normal operation;

1. Clean the filter of water absorption motor and check whether there is damage; Please replace it if necessary.
2. Clean the filter screen on the left side of the clean water tank and check whether it is damaged (FIG.8);Please replace it if necessary.
3. Clean the suction pipe.
4. Clean the water tank and sewage tank.
5. Check the battery capa

Semi-annual maintenance
Ask professional technical personnel to test the circuit system of the machine.

Fault quick check and error code

Trouble Shooting Form

the machine
The battery is run oute| Charge the battery
The emergency button was pressed| Release the emergency button (figure Panel)
The floor doesn’t turn| Didn’t press the brush switch| Press the brush switch
The sewage tank is full| Empty the sewage tank
Brush motor fuse burns out| Check and replace the fuse
Run out of battery| Charge the battery
Motor fault| Replace the motor
Poor cleaning effect| Brush or pads are worn| Replacement
no water coming out| The outlet valve (FIG. 8) is closed| Open the outlet valve
The water in the water tank is insufficient| Fill the tank with water
Outlet pipe blocked| Remove the plug
The water cannot stop| Solenoid valve blocked| Check solenoid valve
Damage of solenoid valve| Replace solenoid valve
Solenoid valve circuit fault| Check solenoid valve circuit
No water during operation| Solenoid valve blocked| Check solenoid valve
Damage of solenoid valve| Replace solenoid valve
Solenoid valve circuit fault| Check solenoid valve circuit
The suction motor cannot be started| No power supply or motor failure of the suction moto| Please check whether the power cable is properly

connected, if in the latter case, please replace the motor

The sewage tank is fully| Empty the sewage tank
Poor water absorption effect| The absorbent strip has worn away| Replacement
The suction pipe or suction outlet is blocked or damaged| Remove the plug or replace the suction pipe
The ball float should be switched off or filled| Empty the tank or replace the float switch
Suction pipe plug| Remove the plug
The suction pipe is not connected or damaged| Connect or replace the suction pipe
No power supply or motor failure of the suction motor| Please check whether the power cable is properly

connected, if in the latter case, please replace the motor

Machines can’t walk| Run out of battery| Charge the battery
There may be a problem with the walk control| Please refer
The emergency button was pressed| Release the emergency button
Machine can’t brake| The control lever of the electronic brake system is locked (FIG.6)| Loosen the control nut (FIG. 6)
Electronic braking system failure| replacement
Battery life is shorter than normal| Electrodes and wiring terminals are oxidized or dirty| Clean and apply vaseline to electrodes and terminals on
The battery charger is not working properly| Check the charger instructions
The battery is normally fully charged, but only for a short period of time| The battery is new, but does not provide 100% performance| New batteries usually require 20-30 recharges to get the best results
The machine needs constant use and the battery capacity is insufficient| Replace a large capacity battery or use another set of charged batteries
The battery charger is not working| Recharge

Alarm code

clear
E01| The mainboard overtemperature| downtime| recoverable
E02| A hardware failure| downtime| The controller needs to be returned to the factory for repair
E03| Clean water tank is empty| Delay shutdown of main brush motor| It will be restored with clean water
E04| Sewage tank is full| Water absorption motor delay stop| Recovery after drainage of sewage
E05| Accelerator pedal failure| downtime| There is a short circuit in the hall sensor of the gas pedal, and the gas pedal needs to be repaired

E06

|

Do not turn off the power when charging

| downtime|

Close the electric door lock to stop alarm, should be  charged according to the normal charging steps:    that is, turn off the power and then connect the charger to charge

E10| Main brush lift motor malfunction| downtime| The main brush lifting motor has a fault or the main board main brush lifting motor driver has a fault
E11| Main brush motor overload| downtime| Unrecoverable, need to shut down to clear
E12| Short circuit of main brush motor| downtime| Unrecoverable, need to shut down to clear
E13| Brush over temperature| downtime| recoverable
E14| Limit switch of main brush push rod is out of order| downtime| Recoverable, two limit switches are all connected when the fault, disconnect any recovery
E20| Water suction lift motor fault| downtime| There is a fault with the water-absorbing gripper motor or a driver fault with the water-absorbing gripper motor on the main board
E21| Water absorption motor overload| downtime| Unrecoverable, need to shut down to clear
E22| Short circuit of suction motor| downtime| Unrecoverable, need to shut down to clear
E23| Suction overtemperature| downtime| recoverable
E24| Failure of limit switch of suction scraper| downtime| Recoverable, two limit switches are all connected when the fault, disconnect any recovery
E30| Discharge solenoid valve malfunctioning| downtime| Unrecoverable, need to shut down to clear
E31| Buzzer failure| downtime| Unrecoverable, need to shut down to clear
E32| Pump failure| downtime| Unrecoverable, need to shut down to clear
E33| Detergent pump failure| downtime| Unrecoverable, need to shut down to clear
E34| Lack of detergent| Detergent pump shutdown| Restore the detergent after filling
Clib| Climbing a prompt|

Lift the main brush and suction rake push rod, main brush and suction motor stop working

| After the machine arrives at the flat ground, press the start button or the suction button to start the corresponding function
SEAt| Seat switch off| Shut down, no beeping sound| recoverable

The product quality commitment
All products are carefully tested and inspected by factory quality inspectors to ensure that the products are free of defects in parts and assembly when they leave the factory.
We provide a one-year warranty for the product (except for vulnerable parts or man-made damage), regular return visits during the warranty period, all repair costs and accessories costs caused by product quality problems are borne by the seller. Or after-sales service by local dealers Contact us.
Note: This warranty does not apply to any accidents caused by maintenance, negligence, abuse, product damage caused by fire, or operation of the machine not in accordance with the operating requirements.
In addition, wearing parts (wheels, rubber strips, absorbent strips, brush trays, needle holders) are not covered by the warranty. The storage battery is a special commodity, which is related to the standard use of the operators. The warranty period is 6 months. If the product is used for other purposes than the product function, the warranty is invalid. Please read the product manual and maintenance manual carefully. All communication and transportation costs, including insurance costs, are paid by the user. Does not include other claims of any nature.

References

• ekat.com - Dichtungen, Schläuche, Gummi und Kunststoff

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>