VESALA MPL9-33 MiniSonde User Manual
- June 10, 2024
- VESALA
Table of Contents
- MPL9-33 Mini Sonder
- GENERAL INFORMATION
- BATTERY INSTALLATION, TURNING ON AND OFF
- OPERATING THE DEVICE
- MAINTENANCE
- TROUBLESHOOTING
- TECHNICAL SPECIFICATIONS
- ACESSORIES & CONSUMABLES
- SAFETY INSTRUCTIONS
- SCOPE OF OPERATION
- MANUFACTURERS WARRANTY
- DECLARATION OF CONFORMITY
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
MPL9-33 Mini Sonder
User Manual
Mini Sonder MPL9-33
MPL9-33 Mini Sonder
This manual contains important operating and safety information. Please read
all instructions carefully before use. Failure to understand and follow
instructions and cautions may lead to damage to your equipment and working
environment.
The serial number of your device is indicated on your Minizone and on the
storage case. The serial number may wear off, enter the serial number below
and always refer to this information when you need to contact the
manufacturer.
VERSION NUMBER SERIAL NUMBER X30-A
IMPORTANT SAFETY INFORMATION
The following symbol is used throughout this manual mark important
instructions. Please take care when meeting this symbol:
GENERAL INFORMATION
The Minizone MPL9-33 is small battery-operated transmitter that emits a 33 kHz
signal, which can be located by a receiver operating on the same frequency.
The Minizone is intended to be used in non-conductive ducts, cavities and
structures.
The device is intended for professional use.
ITEMS SUPPLIED
1 | Minizone transmitter | MPL9-33 |
---|---|---|
2 | Lithium battery | BR535 |
1 | Battery compartment with female M6 thread | MPL9-M6 |
1 | Battery compartment with female M5 thread | MPL9-M5 |
1 | Case with quick reference guide | SB9 |
BATTERY INSTALLATION, TURNING ON AND OFF
Insert a BR535 battery. Observe polarity (Figure 1). To turn the MPL9-33 on,
tighten the battery compartment. The LED at the tip of the Minizone will start
flashing. Take care to fully tighten to avoid water getting into the device.
To turn the Minibond off, unscrew battery compartment. Always remove the
battery completely when you are not using the Minizone.
When the battery has insufficient capacity left for carrying out measurements,
the LED will turn off. Replace the battery. Low temperatures reduce the
operating time of the battery.
High mechanical stress, high ambient temperatures or immersion into liquids
can cause leakage, fire or explosions of the batteries.
Precautions: Protect the batteries from mechanical influences and high ambient
temperatures. Do not drop or immerse batteries into liquids.
OPERATING THE DEVICE
When the battery is inserted and the battery compartment attached, the
Minizone will start emitting a 33 kHz signal. The location can now be detected
with a receiver that operates at the same frequency, such as the Visalia CL43.
Before use, ensure the Minizone is fully functional by locating the signal
with a corresponding receiver. Refer to the user manual of the receiver on
pinpointing the location of the Minizone.
You can attach the Minizone to a duct rod, cable rudder, snake rod, push or
pull rod using the thread at the end of the battery compartment. An O-ring
provides added grip when tightening.
When using the device for blowing with compressed air, always blow with
battery compartment end first. Refer to the user manual of the blowing unit
and follow safe work practices.
Use of compressed air can lead to the Minizone exiting the duct at great
speed.
Precaution: Always use a catcher at the end of the duct. If changing the
direction of the blowing due to the device getting stuck, remember to move the
catcher to the other end of the duct. Do not blow the Minizone with pressure
exceeding 6 bars. Always use safety goggles, when using the MPL9-33 with
compressed air.
MAINTENANCE
CLEANING
Clean with clean, soft cloth. Do not use abrasive agents or solvents for
cleaning.
Take care to avoid dirt getting into the unit. Regularly inspect O-ring and
replace if damaged. If water gets into the battery compartment, allow it to
dry at room temperature.
STORAGE
Store inside storage box. Respect the temperature limits stated in the
technical data when storing the device. Always remove the batteries from the
product during storage to avoid leakage. After a long time of storage, check
the function of the device.
TROUBLESHOOTING
Problem | Possible cause | Remedy |
---|---|---|
Minizone does not turn on. | Battery is weak or wrongly placed. | |
Minizone is damaged | Replace battery, ensure polarity. |
There are no serviceable parts in the device.
Contact your distributor or manufacturer.
Minizone unintentionally turns off.| Battery is weak.| Battery is weak.
No signal is detected.| Battery is weak.
Device is used in conductive duct.| Battery is weak.
Device is used in conductive duct.
DISPOSAL
This product is an electric device and must be collected separately for
disposal according to the European Directive on waste electrical and
electronic equipment.
For business users in the European Union:
If you wish to discard electrical and electronic equipment, please contact
your supplier or manufacturer for further information.
Information on Disposal in other Countries outside the European Union:
This symbol is only valid in the European Union. If you wish to discard this
product, please contact your local authorities or dealer and ask for the
correct method of disposal.
TECHNICAL SPECIFICATIONS
Dimensions; length x diameter | 138 mm x 9 mm |
---|---|
Weight including BR535 battery | 35 g |
Typical range in air* | 5.7 m |
Operating frequency | 32.768 kHz |
Frequency tolerance | ± 3 Hz |
Transmitting power | <10 maw |
Signal type | Continuous |
Battery type | 1 x BR535 |
Typical operating time | 6 h at 20°C |
Typical power consumption | 8 mA at 3.0 V |
Operating temperature | -10°C to +50°C |
Storage temperature | -20°C to +60°C |
Protection | IP67, IK07 |
Max. ambient pressure, air** | 6 bar |
Max. ambient pressure, water | 4 bar |
Mounting threads | M6F, M5F |
Max. speed | 10 m/s |
Max. speed with shock absorber | 20 m/s |
- will vary with choice of receiver, battery voltage, ambient noise and interference.
** Ambient pressure, not jetting pressure. Depending on route, jetting pressure can be higher.
ACESSORIES & CONSUMABLES
Spare battery kit BR535-kit10, 10 pcs BR535 in a storage box | V14047 |
---|---|
O-Ring, Ø 5.82 x 1.2 NBR70 | N01227 |
Shock absorber v2, IV696-96, Ø 9.6 mm | V14701 |
Shock absorber v2, IV696-112, Ø 11.2 mm | V14706 |
Shock absorber v2, IV696-128, Ø 12.8 mm | V14711 |
SAFETY INSTRUCTIONS
Use the following safety guidelines to help ensure your own personal safety
and to help protect your equipment and working environment from potential
damage.
The absence of instruction can lead to incorrect or adverse use, and can give
rise to accidents with far-reaching human, material and financial
consequences. Precaution: All users must follow the safety instructions given
by the manufacturer in this manual.
Watch out for faulty operation if the product has been dropped or has been
misused, modified, stored for long periods or transported. Precautions:
Periodically carry out test measurements with a 33 kHz receiver.
SCOPE OF OPERATION
Permitted use:
The Visalia Minizone MPL9-33 is a short range inductive 32768Hz transmitter
intended to be used in non-conductive ducts, cavities and structures for
locating obstructions and duct calibration.
Adverse use;
- Use of the product without this user manual
- Use of the device against the instructions given in this user manual
- Use outside of the intended limits
- Opening or modifying the device
H. Visalia Oy disclaims any responsibility for damages to persons or property caused by the operation of the device in violation of the instructions contained in this manual.
Adverse use can lead to malfunction and damage.
Precautions: The device is not to be operated until the user has familiarized
himself with this user manual.
EMC
Electromagnetic compatibility is taken to mean the capability of the product to function smoothly in an environment where electromagnetic radiation and electrostatic discharges are present, and without causing electromagnetic disturbances to other equipment. The device meets the strict regulations and standards which are in force in this respect, still the possibility that other equipment may be disturbed or that humans or animals may be affected cannot be excluded.
MANUFACTURERS WARRANTY
H. Visalia Oy provides a warranty for the Minizone MPL9-33 one year from the date of purchase. The warranty covers material or manufacturing defects occurring during this time. During the warranty period H. Visalia Oy shall, at his sole discretion, either repair or replace the defective device or any component thereof. The following are excluded from the warranty: Damage due to improper use, normal wear and tear and defects which only insignificantly impair the value or suitability of use. Any tampering by unauthorized persons shall render the warranty void. Users are advised to contact the manufacturer in case of faults or queries relating to the use of the device.
DECLARATION OF CONFORMITY
Hereby, H. Visalia Oy, declares that the radio equipment type Minizone
MPL9-33
is in compliance with the essential requirements and other relevant provisions
of Directive 2014/53/EU
The full text of the EU declaration of conformity is available at the
following internet address:
http://www.vesala.fi/MPL9-33/doc
H. Visalia Oy
Peräsimentie 1
FI-03100 NUMMELA FINLAND
www.vesala.fi
info@vesala.fi
Tel. +358 44 200 2005
© 2021 H. Visalia Oy All Rights Reserved
References
- Haku- ja testauslaitteita ammattilaiselta ammattilaisille, jo vuodesta 1968 lähtien » Vesala
- Docsis 3.1 testeri » Vesala
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>