air me LISON Ceramic Heater User Manual

: June 10, 2024
: air me

air me LISON Ceramic Heater

Product Information: LISON Connected Heater

Technical Data

Voltage: 220-240 V ~ 50-60 Hz
Dimensions: 285 x 170 x 175 mm (H x W x D)
Net weight: 1.8kg
Heating powers: 3
Maximal power consumption: 2000 W
Suitable for rooms up to: 30 m²
Maximum noise level: 50 dB
Built-in thermostat: Yes
Oscillation: Yes
Protection class: 2

Domestic Injury Prevention

The safety of this product conforms to the relevant norms and regulations in force in the European Union. For any further information, please visit our website: www.airandme.fr/en. Our customer service department is available at the following email address: info@airandme.fr

Important Safety Instructions

The product is only suitable for well insulated spaces or occasional use.
Read instructions carefully before using LISON.
Any use not recommended by the reseller may result in fire, power surges, or injury to persons.
Remove the packaging and make sure that LISON is not damaged. If in doubt, do not use the product and contact your reseller.
Do not allow children to play with any part of the packaging. Pay particular attention to use near a child. Do not leave a child under the age of 3 unsupervised in the same room as LISON.
Before using LISON, make sure that the voltage indicated on the product is in accordance with your electrical installation.
Make sure that the power plug of the unit is correctly plugged in, otherwise the plug may overheat.
Using an extension cord may cause overheating and a risk of fire.
Do not unplug the product by pulling on the cable. Always unplug LISON by holding and pulling the plug.
Do not connect or disconnect the unit with a wet hand.
Do not cover or insert any object that may obstruct the airflow into the unit, as this may result in electric shock or damage to the unit. Do not put your fingers into the air inlet or outlet of the unit as this may cause physical damage.
To avoid burns, do not let bare skin touch the hot surface.
During use, leave at least 50 cm space at the back, sides and front of the appliance. Keep combustible materials such as furniture, bedding, clothing, curtains, etc. at least 1 m away from the appliance.
To avoid electric shock or fire, do not use water, detergent or flammable products to clean the outside or inside of the appliance.
Do not use insecticide spray, perfume, or any other flammable spray around the unit while it is in operation. Do not use the unit in areas where gasoline, paint, or flammable liquids are stored, as there is a risk of fire or explosion.
Never use LISON if there is a risk of falling into a liquid.
Make sure the product is placed on a flat and horizontal surface.
This appliance is for domestic, non-commercial use. Use it inside buildings. Do not use LISON outdoors.
LISON is not for use in bathrooms, laundry rooms, and any other places where there is a risk of splashing water.
Do not use LISON to dry clothes or shoes, or to heat materials.
Always unplug LISON when not in use or when moving around.
Keep the product clean and in good condition.
Use the recommended spare parts (non official parts could be dangerous and in-validate the warranty).
Store LISON in a dry and safe place, away from children.
If the power cord is damaged, it can be changed by the reseller. Only qualified persons can make this repair.
This product cannot be used by children less than 8 years old. Please read carefully this user manual and use LISON with caution.

Product Usage Instructions

Read the instructions carefully before using LISON.
Make sure that the voltage indicated on the product is in accordance with your electrical installation.
Remove any packaging and make sure that LISON is not damaged.
If in doubt, do not use the product and contact your reseller.
Place LISON in a well-insulated space with at least 50 cm space at the back, sides and front of the appliance. Keep combustible materials such as furniture, bedding, clothing, curtains, etc. at least 1 m away from the appliance.
Plug in LISON and ensure that the power plug of the unit is correctly plugged in.
Select your desired mode using the [Mode] and [Timer] button.
Use the [ON-OFF] button to turn LISON on and off.
Use the [Oscillation] button to turn oscillation on or off.
Ensure that no object blocks the airflow into the unit.
Do not put your fingers into the air inlet or outlet of the unit as this may cause physical damage.
Unplug LISON by holding and pulling the plug when not in use, moving it, or cleaning it.

FAQ

The apparatus is not working.
Reason: Something is blocking the fan.
Solution: Ensure that no object blocks the airflow.
Performance of the apparatus has decreased.
Reason: N/A
Solution: N/A
Abnormal noise from the apparatus.
Reason: N/A
Solution: N/A
The apparatus is not producing hot air.
Reason: N/A
Solution: N/A

Problem	Reason	Solution
**** The appliance does not work	> The product is not correctly plug or
there is an electrical problem.	> Plug the socket correctly and check the

voltage and the good functioning of your electrical system.

There is a problem on the electrical system of your house.
Drop in the appliance performance| > The air inlet or outlet is obstructed by something.| > Leave at least 50cm behind, around and in front of the appliance.
Abnormal noise| > Something obstructs the fan.| > Make sure that no object obstructs the air flow.
The product has a functioning problem.| > Contact your reseller for service support.
The unit does not produce hot air| > The [ Fan Mode ] is on.| > Press the [ Mode ] button to select [ Warm Heat Mode ] or [ Hot Heat Mode ].
The unit continues to blow after being switched off.| > This is normal: the unit’s fan shuts off a few seconds after being switched off to cool down more quickly.|

Thank you for having purchased the LISON connected heater, an air&me product. We hope that it will bring you complete satisfaction and improve your indoor air quality.
As with all electrical appliances, it is important to maintain the appliance properly in order to avoid any damage or injury. Please read these instructions carefully before switching the appliance on and keep them for later reference. WAF-direct society accepts no liability for any damage that is caused by noncompliance with this instruction manual. The appliance is only to be used in the household for the intended purposes described in this user manual. Using the appliance for other purposes than the intended ones or performing technical changes to the appliance could be hazardous for health and life.

To prevent from any danger or electrical shock, always unplug the product when you are not using it, moving it or cleaning it. In case of repairs, approach the qualified persons.

COMPONENTS

air me LISON Ceramic Heater 02

Control Panel
Digital display
Hot air outlet grille
Carrying handle
Cold air inlet grille
Main switch of the appliance
Power supply cord

CONTROL PANEL

A & B [ Temperature ] and [ Timer ] buttons
C Button [ ON-OFF ]
D [ Mode ] et [ Timer ] button
E Button [ Oscillation ]
F Luminous ring

DIGITAL DISPLAY

a Ambient temperature
b [ Fan Mode ] Indicator
c [ Warm Heat Mode ] indicator
d [ Hot Heat Mode ] indicator
e [ Wifi ] connection indicator

USE PRECAUTIONS

This unit is only suitable for well insulated rooms or occasional use.
Make sure that the product is placed on a dry and plane surface.
Leave at least 50 cm of space at the back, sides and front of the unit.
Parts of this product may become very hot and cause burns. Pay particular attention when using near children and/or vulnerable persons.

OPERATING INSTRUCTIONS

Plug the unit in.
Press the main switch on the back of the unit ( 6 ) to turn on the power.
Press the [ ON-OFF ] button ( C ) to turn on the unit. The heater starts working. After one minute without any operation, the digital display goes into standby. To turn the screen back on, press any of the buttons.
To turn off the unit, press the [ ON-OFF ] button ( C ) again. The heater will continue to operate and blow air for a few seconds after being turned off.

MAIN FUNCTIONS

D [ MODE ] BUTTON
The [ Mode ] button allows you to choose among 3 heating powers:

Fan : The device blows cold air. A dot appears on the digital display ( b ). The luminous ring is blue.
Warm heat : The unit blows hot air and operates at 1000W. Two dots appear on the digital display ( c ). The luminous ring is orange.
Hot heat : The unit blows hot air and operates at 2000W. Three dots appear on the digital display ( d ). The luminous ring is red.

D [ TIMER ] BUTTON
Pressing the [ Mode ] button for 5 seconds will start the unit’s timer. With the [ Timer setting ] buttons ( A and ( B ), you can set the unit’s operating time between 1 and 9 hours. The display flashes 3 times to confirm the setting. Once the programmed time has passed, the unit will turn off automatically.

E [ OSCILLATION ] BUTTON
The [ Oscillation ] button allows you to activate the oscillation of the heater. The heater will rotate on itself at an angle of about 70°.

ADDITIONNAL FUNCTIONS

THERMOSTAT
The heater has a built-in thermostat that allows you to program a desired temperature between 16 and 37°C. To do so, simply set the desired temperature using the [ Temperature setting ] buttons ( A ) and ( B ). The screen flashes 3 times to confirm the setting.
In [ Warm Heat Mode ] and [ Hot Heat Mode ] (orange or blue illuminated ring), the heater will continue to blow air for 30 seconds as soon as the target temperature is reached, then will stop automatically.

WIFI
To turn on the [ Wifi ] function, press the [ Raise ] ( A ) and [ Oscillation ] ( E ) buttons simultaneously. A dot appears and flashes in the lower right of the digital display ( e ). This activates the wifi pairing between the device and your smartphone. Once this pairing is complete, you will be able to control the heater remotely, as long as you have an internet connection.

SECURITY

THERMAL SAFETY – OVERHEATING PROTECTION
In the event of overheating, the safety device is automatically activated and the unit switches off. Unplug the unit and allow it to cool for several minutes. Then restart the unit as normal.

ANTI-TIP SAFETY DEVICE
The unit is equipped with an anti-tip safety system, which automatically switches off the unit if it tips over.

MAINTENANCE

Let the unit cool completely before handling or cleaning.
Make sure that the appliance is off and unplug before performing any work.
Do not immerse the appliance in water or in any other liquid.
Do not use corrosive, abrasive or flammable products to clean the appliance.

CLEANING THE APPLIANCE: USE A SOFT CLOTH TO REMOVE DUST AT THE AIR INLETS AND OUTLETS.
STORAGE: When not in use, store the product in a dust-free, clean, dry and ventilated place, away from metal objects if possible. Do not place heavy objects on the unit during storage as this may damage it.

Warranty

The appliances are under warranty for a 2-year period from the purchase date. The warranty covers all failures resulting from hidden manufacturing or raw material defects. This warranty does not cover failures or damages resulting from an inadequate setup or usage, or from the normal wear and tear of the product. Spare parts are also available for a period of 2 years after the date of purchase.
Air&me cannot be held liable in case of an inadequate or dangerous use of the products.

DEEE

Disposal of Electric and Electronic Equipment (Applicable in the countries of the European Union and other European countries with separate collection systems appropriate). This symbol on the product indicates that this product shall not be treated as household waste. It should be handed over to the applicable collection point for the recycling of EEE (Electrical and Electromagnetic Equipment). By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health. The recycling of materials will help to conserve natural resources. For additional information about recycling of this product, please contact the municipality, the waste or the retailer.
183 av. Georges Clémenceau
92000 NANTERRE – FRANCE
info@airandme.fr
+33 9 72 232 232