TILTA DJI RS 3-RS 2 Advanced Ring Grip User Guide

June 10, 2024
TILTA

TILTA DJI RS 3-RS 2 Advanced Ring Grip

DISCLAIMERS AND WARNINGS

Thank you for purchasing a TILTA product. What is mentioned in this article is related to your safety, legal rights and liabilities. Before using this product, please read this article carefully to ensure a proper configuration. Failure to follow the instructions or any disregard for the warnings may cause harm to you and other people, and may cause damage to this product and surrounding objects. TILTA owns the right to final interpretation of this document and all other collateral documents. Updates on information are subject to change without prior notice.

For up-to-date product information, please visit the official website, www.tilta.com.
By using this product, you hereby signify that you have read this disclaimer and warning carefully and that you understand, agree to, and
accept the terms and conditions herein. You agree that you are solely responsible for your own conduct while using this product and for any consequence thereof. You agree to use this product only for proper purposes and abide by all the terms, policies and guidelines TILTA has made and may make.

TILTA accepts no liability for damage, injury or any legal responsibility incurred directly or indirectly from the use of this product. The user shall observe sate practices including, but not limited to, those set forth in this document.

Despite the terms mentioned above, consumers’ rights and interests are still protected by local laws and regulations, and are not affected by
this disclaimer.

TILTA is a trademark of Shenzhen TILTA Technology Co., Ltd. and its affiliated companies. Product names and brands in this document are trademarks or registered trademarks of its affiliates.

LAYOUT

BASIC RING GRIP

  1. Power Supply Handle Attachment
  2. Power Port – Top
  3. Ring Grip – Top Arm
  4. Tie Down Ring
  5. Handle
  6. Tie Down Ring
  7. Power Port – Bottom
  8. Foot Release
  9. Foot
  10. Tie Down
  11. Cold Shoe
  12. Tie Down Ring
  13. Handle
  14. Tie Down Ring
  15. Ring Grip – Bottom

ASSEMBLY

  1. Press down the foot release buttons and turn the feet outwards.

  2. Align the contact points and screw on the two bottom arms of the ring grip. To tighen, rotate counter-clockwise.TILTA-DJI-RS-3-RS-2-Advanced-Ring-Grip-FIG-2

  3. Align the power supply handle attachment with the locating point.
    Install to the center of the top arm and tighten with screws.

    • Insert DJI R$ 2 battery grip into the power supply handle attachment and tighten the tie down.
  4. Attach the top arm to the two handles. To tighten, rotate clockwiseTILTA-DJI-RS-3-RS-2-Advanced-Ring-Grip-FIG-3

  5. Attach DJIRS 2 to the ring grip.

  6. The basic ring grip setup is complete.TILTA-DJI-RS-3-RS-2-Advanced-Ring-Grip-FIG-4

  7. Attach the power supply module to the power port on the top arm. Tighten with the screws.
    The built-in cold shoe, 1/4™ 20, and 3/8″ 16 screw points are compatible with monitor mount, phone mount, etc. The 14.8v P-tap port and USB port can power on-board monitor and phone. (Optional)
    Note: Please install the accessories according to your shooting needs.

  8. V-mount or gold mount battery plate can be installed to power port on the bottom arm. Tighten with the screws. Used to supply uninterrupted electric power. (Optional)TILTA-DJI-RS-3-RS-2-Advanced-Ring-Grip-FIG-5 Note: This is compatible with both power ports on the top and bottom arms.

  9. To control the lens wirelessly, replace the basic ring grip handles with remote control handle and dual channel wireless lens control handle. (Optional)

  10. The advanced ring grip setup is complete.TILTA-DJI-RS-3-RS-2-Advanced-Ring-Grip-FIG-6

QR SCAN

CONTACT

All copyrights belong to Tilta Technology Co. Ltd. Written permission is needed for any reproductions. Tilta has the right to adjust product specifications without notice. All measurements are for reference only. Please see the actual products for more details.
TILT is a registered trademark owned by Tilta Technology Co., Ltd.

  • Website: www.tilta.com
  • US Address: 2801 W Magnolia Blvd, Burbank, CA 91505
  • US Contact Number: +1 818)651-4991

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals