SelectBlinds Casual Light Filtering Dual Shades Instruction Manual

SelectBlinds Casual Light Filtering Dual Shades

To Obtain Service: If you suspect this product has a manufacturing defect in materials or workmanship:

Locate the sales receipt

• Call place of purchase Any unauthorized returns will not be accepted.

Warranty Remedy: This shall be your sole remedy under this limited warranty. If this product is found to have a manufacturing defect in materials or workmanship, we will, at our discretion, do one of the following:

• Repair the product
• Replace the product
• Refund the cost of the product.

Colors may vary from lot to lot and may not exactly match sample swatches or previous purchases.
Discontinued items or color selections will be replaced with the closest equivalent current product.
Your rights under state law: This lifetime limited warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow limitations on how long a warranty lasts, so the above limitations may not apply to you. No agent, representative, dealer or unauthorized employee has the authority to increase or alter the obligation of this warranty. This lifetime limited warranty supersedes any previous versions.

WARNING

Window Blind Cord Can STRANGLE Your Child

• Children can climb furniture to reach cords.
• Move crib and furniture away.
• Keep all cords out of children’s reach.
• Attach tension device to wall or floor.
• Fasteners provided with tension device may not be appropriate for all amounting surfaces.
• Use appropriate anchors for the mounting surface conditions.

Continuous Loop Dual Shade

INSTALLATION INSTRUCTIONS
Step 1. Check Package Contents Missing part? Call 1-800-264-1190 Mounting hardware kit includes the following:

Step 2. Tools Required
Pencil, tape measure, level, screw driver, pliers, step stool, drill.

Step 3. Installation
Your blind may be installed either inside the window frame or outside the window frame.
Wallboard or Plaster: use wall anchors. Concrete, Stone, Brick: use a masonry drill bit and anchors or screws specifically designed for masonry (not included).

Inside Mounting:
One bracket should be positioned about 2” to 6” from each end of the head rail. For wider shades that require 3 or 4 brackets, these should be spaced evenly between the two outermost brackets.
Attach each bracket to the inner top of the window opening using the screws provided. Pre-drill the screw holes using a 5/64” drill bit. The extension brackets are not used for inside mounts.
For flush inside mounts, attach the brackets to the head rail first (see drawings and attachment instructions below), and then position the shade in the window opening as desired. Then make pencil marks at the back of each bracket. Remove the brackets by pressing on the plastic tab. Align the brackets with the pencil marks, and then screw them in place as described above.

Outside Mounting:
Attach the Extension Brackets to the wall or window framing. One bracket should be positioned about 2” to 6” from each end of the head rail. For wider shades that require 3 or 4 brackets, these should be spaced evenly between the two outermost brackets. Pre-drill the screw holes using a 5/64” drill bit.
The brackets must be level – use a Spirit Level if necessary to assure proper alignment.
Then attach a Mounting Bracket to each Extension Bracket using the nut and bolt pre-attached to each Extension Bracket.
To adjust head rail extension, remove the shade from the mounting brackets by pressing on the plastic tabs at the front of each bracket. Then loosen the nut and bolt, and move the mounting brackets forward or backward as preferred.

Step 4. Securing the Head Rail
Slide the inner rear of the head rail onto the metal tabs at the back of each bracket, and then push up so that the brackets snap onto the head rail.

IMPORTANT FINAL STEP TO PROPERLY SECURE BRACKETS: pull the plastic tab on the front of each bracket outward toward the front of the shade to lock the brackets in place. For inside-mounts use pliers to grasp the tabs. Check carefully to assure that each bracket is properly secured

Step 5. Install the Chain Tension Device The tension device must be installed to make sure the shade is fully operable. While holding the tension device in one hand, pull the plunger away from the bead chain with the other hand. Lift the bead chain out of the bead locking groove and slide the tension device to the bottom of the chain loop.

Pull the tension device down until the bead chain is fully tensioned (plunger will be at the top) and then move the tension device up approximately 1/8”. Mark the screw hole locations on the wall with a pencil.

Inside Mount: if mounting into wood, pre-drill screw holes and then install the tension device using the 1¼” Phillips head screws provided.
If not securing into wood, use appropriate anchors for the substrate and follow anchor manufacturer’s instructions.
Outside  Mount: Align the mounting bracket screw holes with the pencil marks. If mounting into wood, pre-drill screwholes and then install the mounting bracket using the 1¼” Phillips head screws provided.

If not securing into wood, use appropriate anchors for the substrate and follow manufacturer’s instructions.
Press the tension device onto the mounting bracket posts. Carefully attach the Tension Device to the bracket using the 3/8” Phillips head screws provided. DO NOT OVER-TIGHTEN.

Step 6. How to Operate
Pulling downward on the front or rear cord of the cord loop raises and lowers the shade. Always pull the cords slowly and evenly to maintain the optimal performance of your shade.

CLEANING
To clean the shade fabric, use a feather duster or vacuum lightly using the soft brush or upholstery attachment. For spot cleaning, use warm (not hot!) water with a mild soap to damp clean.

REPLACEMENT PARTS
In the event that replacement parts are ever needed, you may call: 1-800-264-1190

Please be sure to provide the following information, if possible:

• The complete model or catalog number of your product
• A description of the product
• A description of the part needed

LIMITED LIFETIME WARRANTY

The enclosed product is warranted to the original residential retail purchaser as long as the product remains in the original window.
Covered
Lifetime: Entire product against manufacturing defects (i.e. a flaw in the product design, materials, or workmanship that causes the product to no longer function.
3 Years: Cords, including internal cords such as those found in cordless blinds or shades.
5 Years: All fabric
Not Covered

1. Normal wear and Tear
2. Any product that fails due to:
   • Abuse
   • Exposure to salt air
   • Improper installation
   • Accident
   • Extraordinary use
   • Improper operation
   • Alterations
   • Improper cleaning
   • Misapplication
   • Damage from pests/insects/pets
   • Improper handling
   • Misuse
3. Natural Wood Products that have:
   • Loss of color intensity
   • Variations in color, grain or texture
   • Warping of wood slats in high humidity areas

Costs associated with:

• Product removal
• Brand label removal
• Product reinstallation
• Incidental or consequential damages
• Transportation to/from the retailer
• Product re-measure
• Shipping
  In the event there are multiple blinds/shades in the same room, only the defective blind/shade will be replaced.

To Report Shipping Damage: If damage occurred during shipping, call the place of purchase and report within 7 calendar days, or you may be denied credit for your damaged product.

Warranty Remedy: This shall be your sole remedy under this limited warranty. If this product is found to have a manufacturing defect in materials or workmanship, we will, at our discretion, do one of the following:

• Repair the product
• Replace the product
• Refund the cost of the product.

Colors may vary from lot to lot and may not exactly match sample swatches or previous purchases.
Discontinued items or color selections will be replaced with the closest equivalent current product.
Your rights under state law: This lifetime limited warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow limitations on how long a warranty lasts, so the above limitations may not apply to you. No agent, representative, dealer or unauthorized employee has the authority to increase or alter the obligation of this warranty. This lifetime limited warranty supersedes any previous versions.

INSTALLATION INSTRUCTIONS
Step 1. Check Package Contents Missing part? Call 1-800-264-1190 Mounting hardware kit includes the following:

Step 2. Tools Required
Pencil, tape measure, level, screw driver, pliers, step stool, drill.

Pencil, tape measure, level, screw driver, pliers, step stool, drill.

Step 3. Installation
Your blind may be installed either inside the window frame or outside the window frame.
Wallboard or Plaster: use wall anchors. Concrete, Stone, Brick: use a masonry drill bit and anchors or screws specifically designed for masonry (not included).

Inside Mounting:
One bracket should be positioned about 2” to 6” from each end of the head rail. For wider shades that require 3 or 4 brackets, these should be spaced evenly between the two outermost brackets.
Attach each bracket to the inner top of the window opening using the screws provided. Pre-drill the screw holes using a 5/64” drill bit. The extension brackets are not used for inside mounts.
For flush inside mounts, attach the brackets to the head rail first (see drawings and attachment instructions below), and then position the shade in the window opening as desired. Then make pencil marks at the back of each bracket. Remove the brackets by pressing on the plastic tab. Align the brackets with the pencil marks, and then screw them in place as described above.

Outside Mounting:
Attach the Extension Brackets to the wall or window framing. One bracket should be positioned about 2” to 6” from each end of the head rail. For wider shades that require 3 or 4 brackets, these should be spaced evenly between the two outermost brackets. Pre-drill the screw holes using a 5/64” drill bit.
The brackets must be level – use a Spirit Level if necessary to assure proper alignment.
Then attach a Mounting Bracket to each Extension Bracket using the nut and bolt pre-attached to each Extension Bracket.
To adjust head rail extension, remove the shade from the mounting brackets by pressing on the plastic tabs at the front of each bracket. Then loosen the nut and bolt, and move the mounting brackets forward or backward as preferred.

To adjust head rail extension, remove the shade from the mounting brackets by pressing on the plastic tabs at the front of each bracket. Then loosen the nut and bolt, and move the mounting brackets forward or backward as preferred.

Step 4. Securing the Head Rail
Slide the inner rear of the head rail onto the metal tabs at the back of each bracket, and then push up so that the brackets snap onto the head rail.

IMPORTANT FINAL STEP TO PROPERLY SECURE BRACKETS: pull the plastic tab on the front of each bracket outward toward the front of the shade to lock the brackets in place. For inside-mounts use pliers to grasp the tabs. Check carefully to assure that each bracket is properly secured

Step 5. Attach Handle
Attach the clear plastic Handle to the center of the bottom rail as illustrated.

Wider shades have (2) Handles – to precisely determine the correct position for each handle, divide the total width of the shade by 4, and then attach one handle that distance from each outside edge of the bottom rail – always grasp both handles when lifting and lowering the shade.

Step 6. How to Operate
IMPORTANT
Operating & Care Instructions for Cordless Shades

READ CAREFULLY

• To maintain optimal performance of the springs that make your cordless shade function, lift and lower your shade through its full range of motion – all the way up and down – frequently.

GO SLOW!
Be sure the bottom rail handles are properly positioned as described above (step 5) – lift or lower the shade slowly and evenly, keeping the rail level, until the shade is positioned as desired. IMPROPER OPERATION CAN DAMAGE THE SHADE.

• If you have trouble lifting your cordless shade:
  If the shade is left in one position for a long period of time, it might be necessary to lift and lower the shade several times to restore normal function. If the shade has been fully raised for a long period of time, it might tend to spring-back (rebound) slightly from the desired length position. This can also be remedied by lifting and lowering the shade several times.

CLEANING
To clean the shade fabric, use a feather duster or vacuum lightly using the soft brush or upholstery attachment. For spot cleaning, use warm (not hot!) water with a mild soap to damp clean.

REPLACEMENT PARTS
In the event that replacement parts are ever needed, you may call: 1-800-264-1190
Please be sure to provide the following information, if possible:

• The complete model or catalog number of your product
• A description of the product
• A description of the part needed

LIMITED LIFETIME WARRANTY
The enclosed product is warranted to the original residential retail purchaser as long as the product remains in the original window.

Covered
Lifetime: Entire product against manufacturing defects (i.e. a flaw in the product design, materials, or workmanship that causes the product to no longer function.

• 3 Years: Cords, including internal cords such as those found in cordless blinds or shades.
• 5 Years: All fabric
• Not Covered

1. Normal wear and Tear
2. Any product that fails due to:
   • Abuse
   • Exposure to salt air
   • Improper installation
   • Accident
   • Extraordinary use
   • Improper operation
   • Alterations
   • Improper cleaning
   • Misapplication
   • Damage from pests/insects/pets
   • Improper handling
   • Misuse
3. Natural Wood Products that have:
   • Loss of color intensity
   • Variations in color, grain or texture
   • Warping of wood slats in high humidity areas

Costs associated with:

• Product removal
• Brand label removal
• Product reinstallation
• Incidental or consequential damages
• Transportation to/from the retailer
• Product re-measure
• Shipping

In the event there are multiple blinds/shades in the same room, only the defective blind/shade will be replaced.

To Report Shipping Damage: If damage occurred during shipping, call the place of purchase and report within 7 calendar days, or you may be denied credit for your damaged product.

To Obtain Service: If you suspect this product has a manufacturing defect in materials or workmanship:

• Locate the sales receipt
• Call place of purchase

Any unauthorized returns will not be accepted.

INSTALLATION INSTRUCTIONS
INSTALL THE SHADE BEFORE ATTEMPTING TO OPERATE THE MOTOR.

Tools Required:
Tape measure, pencil, drill, drill bits, screw driver, step stool or ladder .

Note: use a 5/64” drill bit to pre-drill the screw holes (for attachment to a wall stud or header board). Use Wall Anchors (not included) for hollow dry wall or plaster mounting.

Step 1. Mount the Brackets
[Note: If your shade has a Cassette Valance (the shade is pre-mounted in a decorative aluminum cover) locate the special instructions for installing the Cassette]

Attach the brackets to the window frame, molding or ceiling as shown .

Note that the bracket for the motor end of the shade has a tab that fits into the motor housing. The Pin-End Bracket has a slot that the pin end slides into.

Mark the screw locations with a pencil – pre-drill the screw holes using a 5/64” drill bit.

Step 2A. Cassette Installation (for shades with optional Cassette Valance)
The shade is pre-mounted in the cassette. It can be removed to adjust tension, if necessary.
To attach the cassette outside the window frame, use the rear bracket holes as illustrated.
To attach the Cassette inside the window frame (or to the ceiling), use the top bracket holes as illustrated. Attach the Cassette by placing the back- bottom of the head rail into the bottom of each mounting bracket. Push forward and up, snapping the rail into the top of the mounting bracket.

Operating the Shade

IMPORTANT
See the dedicated programming and operating instructions that came with the shade. If you cannot locate these instructions, please call Customer Service.
CUSTOMER SERVICE: 1-800-264-1190

Cleaning
Dusting: Vacuum using the soft brush attachment.
Washing (applies to vinyl or vinyl coated shade material): Use a cloth, sponge or soft brush and a mild detergent. Use warm or cold water, not hot water. Place toweling on the floor or window sill and wash the blind in sections.
REPLACEMENT PARTS
In the event that replacement parts are ever needed, you may call: 1-800-264-1190
Please be sure to provide the following information, if possible:

• • The complete model or catalog number of your product
  • A description of the product
  • A description of the part needed

LIMITED LIFETIME WARRANTY
The enclosed product is warranted to the original residential retail purchaser as long as the product remains in the original window.

Covered
Lifetime: Entire product against manufacturing defects (i.e. a flaw in the product design, materials, or workmanship that causes the product to no longer function.

• 3 Years: Cords, including internal cords such as those found in cordless blinds or shades.
• 5 Years: All fabric
• 3 Years: Battery Operated Motors

Not Covered

1. Normal wear and Tear
2. Any product that fails due to:
   • Abuse
   • Alterations
   • Exposure to salt air
   • Improper cleaning
   • Improper installation
   • Misapplication
   • Accident
   • Damage from pests/insects/pets
   • Extraordinary use
   • Improper handling
   • Improper operation
   • Misuse
3. Natural Wood Products that have:
   • Loss of color intensity
   • Variations in color, grain or texture
   • Warping of wood slats in high humidity areas
4. Costs associated with:
   • Product removal
   • Transportation to and from the retailer
   • Brand label removal
   • Product re-measure
   • Product reinstallation
   • Shipping
   • Incidental or consequential damages

In the event there are multiple blinds/shades in the same room, only the defective blind/shade will be replaced

To Report Shipping Damage:
If damage occurred during shipping, call the place of purchase and report within 7 calendar days, or you may be denied credit for your damaged product.

To Obtain Service:
If you suspect this product has a manufacturing defect in materials or workmanship:

• Locate the sales receipt
• Call place of purchase
  Any unauthorized returns will not be accepted.

Warranty Remedy:
This shall be your sole remedy under this limited warranty.
If this product is found to have a manufacturing defect in materials or workmanship, we will, at our discretion, do one of the following:

• Repair the product
• Replace the product
• Refund the cost of the product

Colors may vary from lot to lot and may not exactly match sample swatches or previous purchases. Discontinued items or color selections will be replaced with the closest equivalent current product.

Your rights under state law: This lifetime limited warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow limitations on how long a warranty lasts, so the above limitations may not apply to you. No agent, representative, dealer
or unauthorized employee has the authority to increase or alter the obligation of this warranty. This lifetime limited warranty supersedes any previous versions

Smart WiFi Hub Instructions

1. Download & Install “P2 POWERMATE” APP on your cellphone

2. Search for “P2 POWERMATE” on the App Store or Google play

3. Download “P2 POWERMATE” and install the APP on your phone

4. Register and login to the P2 POWERMATE APP

5. When installation is complete open P2 POWERMATE

6. Create an account using your e-mail address – enter a password that should include letters and numbers only, no signs or special characters

7. Login in to your account (after the account is established you will login to the APP directly)

8. Link the P2 POWERMATE hub to the POWERMATE APP

9. Choose ”Add device” on desktop

10. Choose P2 POWERMATE Smart Hub

11. Choose “Allone Pro”

12. Power on the P2 POWERMATE hub

13. Press and hold the central button on the hub until the circular light turns RED and Flashes

14. Choose “Next” on the P2 POWERMATE APP

15. Choose “Join” to enable the hub to access your Wi-Fi network
    Tip: Make sure your network is available, not restricted to assure access

16. Select your Wi-Fi network and input your Wi-Fi password

17. The P2 POWERMATE hub will connect to your Wi-Fi network automatically. When you see
    “Added successfully” on the P2 POWERMATE APP, choose “Done”

18. The APP is linked to the P2 POWERMATE hub when Allone Pro appears on the desktop

19. Add your shades to the P2 POWERMATE APP

20. Choose “Allone Pro” on the APP desktop

21. Choose “+ Add” at the menus bottom right corner

22. Choose “Motor” device

23. Now press the “programming button” on motor head for 1 second – the shade will oscillate one time. Then tap “pairing” on P2 POWERMATE APP. If the shade is successfully added to the APP, the shade will oscillate one more time.
    If not, repeat the step 4 operation.

24. Choose “Response has been stored” when the shade is successfully added to APP.

25. The shade has been added to the P2 POWERMATE APP. Confirm that you can now control the shade using the APP, and then proceed to add additional shades if applicable.

26. Family “Member Permission” management
    Note that the set-up account is the one and only administrator – only the administrator’s login can make changes to the APP. However, the administration account can add family members with their own ID, and they can then control the shades from their phones or tablets.

27. Choose ”Me” on the P2 POWERMATE desktop, and then Select “family Management” menu

28. Choose “Member Permission”

29. Tap “+” family members at the top right corner of the screen

30. Input your family “Account e-mail address” then go to to bottom, send an invitation to your family member

31. When your family member receives and accepts the invitation, the Administration account shows the family QR Code that the family member will scan The family member taps “+” at the top right corner, and chooses “Add to an existing family”. Choose “scan the family’s QR code to join it”, and then scan the code on the administrators screen.

32. Siri Shortcut” Voice Command Management

33. Choose ”Scenes” on the P2 POWERMATE desktop. Create a scene.

34. Slide the “scene” icon to left, and then choose “Edit” scene

35. Add Execution Task

36. Choose “Device” and then select the shade you want to add to this scene

37. Choose an “Action” for the shade you selected. Then Add to Siri.

38. In the Add to Siri menu, you can edit the “Siri shortcut command”. For example: “open shade in bedroom”. After all tasks are set up, save the scene. Now you can let Siri control your shades.

39. Link to “Amazon Alexa” & “Google home” voice control device

40. Login in your “Amazon Alexa” or “Google home” APP

41. Amazon Alexa” add “Skills & Games” “Google Home” add “Home control”

42. Search “p2 powermate”

43. Choose “ENABLE TO USE”

44. Input your “p2 powermate” account and password, then sign in. Now P2 Powermate had been linked to your “Alexa” or “Google Home” voice control device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>